Skip to the content
2 layers87 × 52 mmModulo3-mcu, the printed circuit board in 3D

Modulo3-mcu

nodep/myAmp4

Battery powered, solid state, guitar amplifier schematic and PCB

Size
87 × 52 mm
Copper layers
2
Thickness
1.6 mm
Parts
67
Nets
77
Pads
236
Tracks, vias
521, 17
Pours
1
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
17 Feb 2020
Updated
1 Dec 2024

Overview

Modulo3-mcu is an open-source printed circuit board by nodep, from the nodep/myAmp repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 87 × 52 mm with 67 parts on 77 nets, routed with 521 tracks and 17 vias.

It is built around the AVR64DA64-E/MR, SN74LVC1G17DBV and 74LVC2G32DC, with the BAT54SW, BS170 and BS250 among its other parts. Its parts include 17 capacitors, 17 resistors, 13 ICs, 2 transistors and 1 diode. It belongs with the audio and music boards of this library.

Main components

6

README

README.md

modulo2

What started as an idea to upgrade the guts of a practice guitar amplifier (Marshall Valvestate 8010), has evolved into a stereo guitar amplifier with effects. The current prototype is housed in a guitar pedal box (119 x 93.5 x 56.5mm). It has a modular design with the preamp, the effects board, and a stereo power amp. These modules are split into their own PCBs.

The preamp

It is based on ESP's project 27 (https://sound-au.com/project27.htm). I have only used the preamp from this project and I have made a few changes:

  • The overdrive section is changed to work as protection and limit the output to 3.3V. This is needed for the inputs of the DSP chip in the effects section (max input of FV-1 is 3.3V).
  • The zener diode rail splitter is changed to a TL2426. Reasons being a smaller footprint and much lower power consumption.
  • The total gain has been reduced on every stage.
  • The tone control values have changed to a more Fender-like sound.

The effects

The effects sections is based on a Spin semiconductor's FV-1 DSP chip. The chip has 8 built-in effects and the ability to read 8 more effects from an external EEPROM. This was extended using a microcontroller (ATmega328p) to up to 50 external effects which are read from the microcontroller's flash memory. The board also has a dry/wet mixer, a master volume. The microcontroller has a driverless USB bootloader which allows easier firmware updates and DSP program modification. A rotary encoder allows for FV-1 program selection and changing the input clock frequency of the FV-1. Some of the FV-1 programs work as a mono input and produce a stereo output with one channel outputing a slightly different signal to the other creating a stereo effect from a mono preamp input. The microcontroller oversees the power section to avoid audible pops during the power-up and power-down.

The power amp

The power section is based on a TPA3220 in a stereo configuration. I have not tested it fully yet, but it should be able to output up to 60W into 4Ω per channel. It is a Class-D amp bringing high efficiency (around 90%) and very low distortion and noise. The TPA3220 chip has an integrated preamp with a selectable gain (4 distinct levels) making the full range of the master volume useful for quiter practice and louder performance levels.

The PCBs for the final prototype have been send to the fab.

Stay tuned for results!

Parts

67
QtyValueFootprintReferences
610kmyAmp:R_10MMR1, R6, R7, R8, R11, R15
610nmyAmp:C_1206C1, C3, C5, C7, C9, C10
4100myAmp:R_10MMR9, R12, R13, R14
4100nmyAmp:C_1206C2, C4, C6, C8
33u3myAmp:CPOL_D4_P1.5C13, C14, C15
34k7myAmp:R_10MMR4, R16, R17
212pmyAmp:C_1206C11, C12
222myAmp:R_10MMR2, R3
1100µFmyAmp:CPOL_D6.3_P2.5C17
110µFmyAmp:CPOL_D4_P1.5C16
11kmyAmp:R_10MMR10
132768HzmyAmp:QUARTZ_85SMXY1
174LVC2G32DCmyAmp:VSSOP-8_2.4x2.1mm_P0.5mmU1
18k2myAmp:R_10MMR5
1AMPCTRLmyAmp:AMPCTRLU8
1AVR64DA64myAmp:TQFP-64_10x10mm_P0.5mmU2
1BAT54SWmyAmp:SOT-23D1
1BS170myAmp:TO-92_Inline_WideQ2
1BS250myAmp:TO-92_Inline_WideQ1
1DBG_UARTmyAmp:DBG_UARTU7
1FOOTSWITCHmyAmp:EXT_JACKU11
1FV1_CONNmyAmp:FV1_CONNU6
1LM1117 3V3myAmp:SOT-223U13
1PA3myAmp:TestPadT1
1PA5myAmp:TestPadT9
1PA6myAmp:TestPadT3
1PC0myAmp:TestPadT4
1PC1myAmp:TestPadT5
1PC4myAmp:TestPadT14
1PC5myAmp:TestPadT15
1PC6myAmp:TestPadT16
1PC7myAmp:TestPadT12
1PD0myAmp:TestPadT11
1PD1myAmp:TestPadT10
1PD2myAmp:TestPadT2
1PF6myAmp:TestPadT8
1PG4myAmp:TestPadT7
1PG5myAmp:TestPadT6
1PG6myAmp:TestPadT13
1PWR_CONNmyAmp:PWR_CONNU10
1SN74LVC1G17myAmp:SOT-23-5U3
1TOUCHSCREEN_240x320myAmp:TOUCHSCREEN_2.8U5
1UPDImyAmp:UDPIU4
1~myAmp:PREAMP_CONNU9
1~myAmp:KNOBSU12

More from nodep/myAmp

11
  • 2 layers302 × 135 mmModulo, the printed circuit board in 3D

    Modulo

    nodep/myAmp

    Battery powered, solid state, guitar amplifier schematic and PCB

    201 parts4GPL-3.0
  • 2 layers94 × 89 mmMyAmp, the printed circuit board in 3D

    MyAmp

    nodep/myAmp

    Battery powered, solid state, guitar amplifier schematic and PCB

    90 parts4GPL-3.0
  • 2 layers105 × 47 mmModulo2-fv1, the printed circuit board in 3D

    Modulo2-fv1

    nodep/myAmp

    Battery powered, solid state, guitar amplifier schematic and PCB

    83 parts4GPL-3.0
  • 2 layers105 × 47 mmModulo2-powamp, the printed circuit board in 3D

    Modulo2-powamp

    nodep/myAmp

    Battery powered, solid state, guitar amplifier schematic and PCB

    76 parts4GPL-3.0
  • 2 layers105 × 47 mmModulo2-eq, the printed circuit board in 3D

    Modulo2-eq

    nodep/myAmp

    Battery powered, solid state, guitar amplifier schematic and PCB

    62 parts4GPL-3.0
  • 2 layers84 × 52 mmModulo3-fv1, the printed circuit board in 3D

    Modulo3-fv1

    nodep/myAmp

    Battery powered, solid state, guitar amplifier schematic and PCB

    57 parts4GPL-3.0
  • 2 layers105 × 47 mmModulo2-pa27, the printed circuit board in 3D

    Modulo2-pa27

    nodep/myAmp

    Battery powered, solid state, guitar amplifier schematic and PCB

    48 parts4GPL-3.0
  • 2 layers84 × 52 mmModulo3-powamp, the printed circuit board in 3D

    Modulo3-powamp

    nodep/myAmp

    Battery powered, solid state, guitar amplifier schematic and PCB

    45 parts4GPL-3.0
  • 2 layers104 × 40 mmModulo3-pa27, the printed circuit board in 3D

    Modulo3-pa27

    nodep/myAmp

    Battery powered, solid state, guitar amplifier schematic and PCB

    44 parts4GPL-3.0
  • 2 layers84 × 52 mmModulo3-power, the printed circuit board in 3D

    Modulo3-power

    nodep/myAmp

    Battery powered, solid state, guitar amplifier schematic and PCB

    31 parts4GPL-3.0
  • 2 layers85 × 23 mmModulo3-fv1-knobs, the printed circuit board in 3D

    Modulo3-fv1-knobs

    nodep/myAmp

    Battery powered, solid state, guitar amplifier schematic and PCB

    10 parts4GPL-3.0

Similar boards

  • 2 layersRaposfly UPS, the printed circuit board in 3D

    Raposfly UPS

    LenaicElsig/ups-RaspberryPi

    Uninterrupted power supply for Raspberry Pi

    45 parts4
  • 2 layers100 × 60 mmVecCRTtap, the printed circuit board in 3D

    VecCRTtap

    raigl/WWI-vecIF

    Vector display interface for Whirlwind simulator

    34 parts2
  • 2 layers100 × 80 mmAddressing nand, the printed circuit board in 3D

    Addressing nand

    drtrigon/eagle

    Results of eagle and kicad CI from travis are stored in https://github.com/drtrigon/eagle/tree/result/pcb branch and linked/shown in https://github.com/drtrigon/sketchbook repo.

    35 parts1MIT
  • 2 layers40.6 × 65.7 mmTransistorDiodes, the printed circuit board in 3D

    TransistorDiodes

    mimeiners/elk

    HSB B.Eng. ET M 5.3

    27 partsApache-2.0
  • 2 layers29.5 × 39 mmH híd, the printed circuit board in 3D

    H híd

    simonyiszk/sem-ultrahang

    SEM-es irányított hangszórós projekt

    12 parts
  • 4 layers100 × 100 mmPintry X2, the printed circuit board in 3D

    Pintry X2

    icamaster/Pintry

    Two bay NAS based on the Raspberry Pi Compute Module 4

    193 parts26MIT
  • 2 layers20.3 × 104.3 mmExpander just back, the printed circuit board in 3D

    Expander just back

    plinkysynth/plinky-expander

    hardware design of a small expander for the plinky synth

    62 parts19
  • 4 layers101.6 × 111.5 mmDaisyplusdac, the printed circuit board in 3D

    Daisyplusdac

    lichen-community-systems/signaletic

    A music signal processing library designed for embedded environments and Web Assembly, in C

    117 parts9MIT

Questions

How big is the Modulo3-mcu PCB?

It measures 87 × 52 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Modulo3-mcu use?

67 parts, built around the AVR64DA64-E/MR, SN74LVC1G17DBV, 74LVC2G32DC and BAT54SW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Modulo3-mcu KiCad files?

From the nodep/myAmp repository on GitHub, at the commit this page was made from: the board is circuit/modulo3-mcu.kicad_pcb and its schematic circuit/modulo-fv.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Modulo3-mcu design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).