

Usbc i2c
USB-C → 3.3V → I²C breakout board — circuit_toolkit PCBA-2 test project
- Size
- 50 × 30 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 14
- Nets
- 8
- Pads
- 50
- Tracks, vias
- 44, 4
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 28 Apr 2026
- Updated
- 29 Apr 2026
Overview
Usbc i2c is an open-source printed circuit board by nickleassdimebutt, from the nickleassdimebutt/usbc-i2c repository on GitHub. It is a 2-layer board of 50 × 30 mm with 14 parts on 8 nets, routed with 44 tracks and 4 vias.
It is built around the AMS1117-3.3. Its parts include 5 resistors, 3 capacitors, 2 connectors, 1 IC and 1 diode. It belongs with the interfaces and adapters boards of this library.
Main components
1README
README.mdusbc-i2c
USB-C powered I²C breakout — 5 V in, 3.3 V out, 10 kΩ SDA/SCL pullups, 4-pin header to chain sensors. Power-good LED (green) on +3V3.
PCBA-2 test project for the kicad-claude-toolkit v3 toolchain. Tighter layout than usbc-charger (14 components vs 23) so hand-routed tracks could go DRC-clean for the routing that does exist.
Layout status
The validated routes from usbc-3v3 (J1 escape, VBUS bus, CC pulldowns, GND bridges) are reused verbatim. The new fan-out (+3V3 to LDO output caps, the I²C pullups, the LED, the 4-pin user header) is left for KiCad GUI hand-routing — same reason as usbc-charger: code-only routing without a visual feedback loop accumulates pad-coordinate errors very quickly.
DRC reports:
- 10 unconnected items — every +3V3 / SDA / SCL / N_D1 stub (expected, routing TODO)
- 1 dangling track — leftover endpoint from a stub I trimmed
- 4 cosmetic silk warnings (overlap, edge clearance, copper clip) — all non-fatal, would be silenced via project rule overrides
The board is topologically correct (circuit.py builds, BOM is
clean, schematic SVG renders) and the full datasheet pipeline runs
end-to-end on it.
Build
& "C:\Program Files\KiCad\10.0\bin\python.exe" build.py --datasheet --simTopology summary
| Block | Components | Function |
|---|---|---|
usbc_power | J1 + R1, R2 | USB-C 5 V input + CC pulldowns |
ldo | U1 + C1, C2, C3 | AMS1117-3.3 LDO with bypass caps |
i2c_pullups | R10, R11 | 10 kΩ SDA / SCL pullups to +3V3 |
led | D1 + R3 | Green +3V3 power-good indicator |
header | J2 | 4-pin I²C user header (3V3/GND/SDA/SCL) |
mounting | H1, H2 | Two M2 corner holes |
14 components, 8 nets, 50 × 30 mm.
Parts
14| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10k | R_0402_1005Metric | R10, R11 |
| 2 | 10uF | C_0805_2012Metric | C1, C2 |
| 2 | 5.1k | R_0402_1005Metric | R1, R2 |
| 2 | MountingHole_M2 | MountingHole_2.2mm_M2 | H1, H2 |
| 1 | 100nF | C_0402_1005Metric | C3 |
| 1 | 820.0 | R_0402_1005Metric | R3 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U1 |
| 1 | GREEN | LED_0805_2012Metric | D1 |
| 1 | HRO TYPE-C-31-M-12 | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | I2C | PinHeader_1x04_P2.54mm_Vertical | J2 |
Similar boards
- 2 layers290.1 × 130 mm

- 2 layers26.2 × 45.5 mm

PL18 multiprotocol
pascallanger/DIY-Multiprotocol-TX-Module
Multiprotocol TX Module (or MULTI-Module) is a 2.4GHz transmitter module which controls many different receivers and models.
24 parts1.9kGPL-3.0 - 4 layers99 × 53.3 mm

PSLab
fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io
199 parts1.7kApache-2.0 - 4 layers85 × 56 mm

- 4 layers100 × 54 mm

32Bit shift register
MaltWhiskey/Mega-Cube
16x16x16 PL9823 Cube with Teensy 4.0 and FlexIO driver
64 parts766 - 2 layers44.2 × 29.3 mm

- 2 layers78 × 60 mm

- 2 layers59.1 × 99.9 mm

Cheap FOCer 2 60mm
shamansystems/Cheap-FOCer-2
Low-Cost Motor Controller based on the VESC 6
193 parts407
Questions
How big is the Usbc i2c PCB?
It measures 50 × 30 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Usbc i2c use?
14 parts, built around the AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Usbc i2c KiCad files?
From the nickleassdimebutt/usbc-i2c repository on GitHub, at the commit this page was made from: the board is usbc-i2c.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Usbc i2c design in my own project?
Its repository states no licence, so its author keeps all rights: ask nickleassdimebutt before reusing the design.