
Flying byte v1
PanBabinicz/ghost-feather
Here: - -n myenv specifies the environment name - python=3.10 installs a specific Python version

This project is a PCB built around an STM32WB for RF Bluetooth connection.
STM32WB PCB2 is an open-source printed circuit board by NasserTaqi, from the NasserTaqi/STM32WB_Bluetooth_PCB repository on GitHub. It is a 4-layer board of 53.5 × 28.8 mm with 52 parts on 56 nets, routed with 261 tracks and 205 vias.
It is built around the STM32WB55CEU6, DLF162500LT-5028A1 and MIC5365-3.3YD5-TR, with the USBLC6-2SC6, RT0402BRD07220RL and 0402ZD475KAT2A among its other parts. Its parts include 20 capacitors, 8 resistors, 4 connectors, 3 ICs and 3 inductors. It belongs with the radio and wireless boards and the STM32 boards of this library.
This project is a PCB built around an STM32WB for RF Bluetooth connection.
The board is 4 layers with the following stack-up:
Layer: 1 SIGNAL
Layer: 2 GND
Layer: 3 GND
Layer: 4 SIGNAL



| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100n | Capacitor_SMD:C_0402_1005Metric | C2, C4, C5, C6, C7, C8, C9, C10, C12, C13, C20 |
| 5 | 220R | Resistor_SMD:R_0402_1005Metric | R3, R4, R6, R7, R8 |
| 5 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C1, C3, C11, C16, C17 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_2.2mm_M2_Pad_Via | H1, H2, H3, H4 |
| 3 | 5.1k | Resistor_SMD:R_0402_1005Metric | R1, R2, R5 |
| 3 | Fiducial | Fiducial:Fiducial_1mm_Mask2mm | FID1, FID2, FID3 |
| 2 | 10p | Capacitor_SMD:C_0402_1005Metric | C14, C15 |
| 2 | LED | LED_SMD:LED_0402_1005Metric | D1, D2 |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW1, SW2 |
| 1 | 0.3p | Capacitor_SMD:C_0402_1005Metric | C19 |
| 1 | 0.8p | Capacitor_SMD:C_0402_1005Metric | C18 |
| 1 | 10n | Inductor_SMD:L_0402_1005Metric | L1 |
| 1 | 10u | Inductor_SMD:L_0805_2012Metric | L2 |
| 1 | 2.7n | Inductor_SMD:L_0402_1005Metric | L3 |
| 1 | 32.768KHz | Crystal:Crystal_SMD_2012-2Pin_2.0x1.2mm | X1 |
| 1 | 32MHz | Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm | X2 |
| 1 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Conn_ARM_SWD_TagConnect_TC2030 | Connector:Tag-Connect_TC2030-IDC-FP_2x03_P1.27mm_Vertical | J2 |
| 1 | Conn_Coaxial | Connector_Coaxial:U.FL_Hirose_U.FL-R-SMT-1_Vertical | J4 |
| 1 | DLF162500LT-5028A1 | Samacsys:DLF162500LT5028A1 | FLT1 |
| 1 | MIC5365-3.3YD5 | Package_TO_SOT_SMD:TSOT-23-5 | U2 |
| 1 | STM32WB55CEU6 | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U3 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |

PanBabinicz/ghost-feather
Here: - -n myenv specifies the environment name - python=3.10 installs a specific Python version

arsovskiteodor/A.ProdDeck
Open-hardware macro pad (WIP): custom KiCad PCB with keys, encoders and a fader, plus firmware and a desktop configurator

justinfederico/STM32testPCB
Custom STM32WB microcontroller to practice my PCB schematic and layout skills. Looking to get it printed soon! Bear in mind that this is an ameuter project, so there will probably be errors aplenty.

dibreyjonatan/SAFE-ROOM
SAFE ROOM est une dispositif électronique qui permet de connaitre en temps réel, les conditions d'une pièce. A savoir la qualité d'air, la temperature, l'humidité, et la pression.

davispe1/wearable-imu
Node PCB — revision 1.0. 4-layer board (F.Cu, In1.Cu, In2.Cu, B.Cu).



It measures 53.5 × 28.8 mm and has 4 copper layers, 1.61 mm thick.
52 parts, built around the STM32WB55CEU6, DLF162500LT-5028A1, MIC5365-3.3YD5-TR and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the NasserTaqi/STM32WB_Bluetooth_PCB repository on GitHub, at the commit this page was made from: the board is STM32WB_PCB2/STM32WB_PCB2.kicad_pcb and its schematic STM32WB_PCB2/STM32WB_PCB2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask NasserTaqi before reusing the design.