
Relatively Universal ROM Programmer
AndersBNielsen/Relatively-Universal-ROM-Programmer
Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.

Arduino IDE を使って、同リポジトリ内の2023kyurobo.cをArduinoに書き込みます ※プログラムは、Arduino UNO R3 での動作を想定して書かれています
2023Kyurobo Meishi is an open-source printed circuit board by nalinally, from the nalinally/2023kyurobo repository on GitHub. It is a 2-layer board of 82.7 × 50 mm with 24 parts on 40 nets, routed with 57 tracks and 0 vias.
It is built around the ARDUINO UNO R3. Its parts include 7 resistors, 7 diodes and 2 switches. It belongs with the AVR (ATmega, ATtiny) boards of this library.
本基板名刺は、Arduinoにプログラムを書き込んで挿すことで、連打綱引きゲームができるようになります。
※動作確認はしておりません。あしからず。
・タクトスイッチ 2個
・led 7個
・1kくらいの抵抗 7本
基板に書いてある通りに実装していきます
Arduino IDE を使って、同リポジトリ内の2023kyurobo.cをArduinoに書き込みます
※プログラムは、Arduino UNO R3 での動作を想定して書かれています
両者がスイッチを押すとカウントが始まり、その状態で3秒間押し続けて、真ん中のLEDが光るとゲームスタートです
ひたすらスイッチを連打します。最初は真ん中のLEDが光っていますが、より連打数が多いほうに徐々に引き寄せられていきます。
自分に一番近いLEDを先に光らせたほうの勝利です。
| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | LED | LED_THT:LED_D3.0mm | D1, D2, D3, D4, D5, D6, D7 |
| 7 | R | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R2, R3, R4, R5, R6, R7 |
| 2 | SW_DIP_x01 | Button_Switch_THT:SW_PUSH_6mm_H7.3mm | SW1, SW2 |
| 1 | Arduino_UNO_R3 | Module:Arduino_UNO_R3 | A1 |
| 1 | LOGO | Meishi:NITOC | G*** |
| 1 | LOGO | Meishi:nally_robocon_30mm | G*** |
| 1 | LOGO | Meishi:obamanarito | G*** |
| 1 | LOGO | Meishi:2023kyurobo_repository | G*** |
| 1 | LOGO | Meishi:shi-sa-kun_50mm | G*** |
| 1 | LOGO | musojin:30mm | G*** |
| 1 | LOGO | Meishi:Robocon_NITOkC_25mm | G*** |

AndersBNielsen/Relatively-Universal-ROM-Programmer
Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.

AlanFord/self-balancing-stick
Dual Axis Reaction Wheel Inverted Pendulum

Edging-Machines/Edging-Machines
This repository is intended to contain as much information as possible about building, designing, prototyping, and using automated edging machines.

PedroCNeves/AC_ChargingStation
A learning project to create an EV AC Charging station based on an Arduino Uno

jonsag/arduTester
An arduino component tester based on https://create.arduino.cc/projecthub/plouc68000/ardutester-v1-13-the-arduino-uno-transistor-tester-dbafb4


ICRS/101
The all-new open source Robotics 101 course from ICRS. It's specifically designed to be run in hackspaces, after school clubs and university societies.

It measures 82.7 × 50 mm and has 2 copper layers, 1.6 mm thick.
24 parts, built around the ARDUINO UNO R3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the nalinally/2023kyurobo repository on GitHub, at the commit this page was made from: the board is 2023Kyurobo_Meishi/2023Kyurobo_Meishi.kicad_pcb and its schematic 2023Kyurobo_Meishi/2023Kyurobo_Meishi.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask nalinally before reusing the design.