
Jetson AI Cam CopperPilot
CopperPilot/Jetson-AI-Cam-CopperPilot
A carrier for Jetson Nano, Xavier NX and TX2 NX with two IMX219 cameras on a 39 mm stereo baseline, dual 4K outputs and CAN.

canbus volvo reverse engineering
Controller is an open-source printed circuit board by najnesnaj, from the najnesnaj/moosesnif repository on GitHub. It is a 2-layer board of 53 × 36 mm with 35 parts on 59 nets, routed with 134 tracks and 29 vias.
It is built around the MAX3051EKA. Its parts include 10 resistors, 7 capacitors, 5 connectors, 3 ICs and 2 diodes. It belongs with the interfaces and adapters boards and the STM32 boards of this library.
canbus volvo reverse engineering
In this repository you can find a manual in pdf format, it is work in progress but could offer some insight in howto deal with Volvo CANBUS traffic.
I try to reverse engineer canbus traffic on a Volvo P1, but my effort is usable for all pre-2015 vehicles.
The ultimate goal is an EV conversion.
I modified the OpenMoose program, to send messages over the canbus using the Volvo DICE cable. (this already works!) Unfortunately I'm a lousy programmer and not really at ease in the Microsoft world, so if anybody can help out, send me a mail. I'm working on sniffing canbustraffic using the J2534 DLL. Should work, I guess, and it would be really useful since no extra hardware would be needed.
You can find a modified stm32 openlib3 program, which ultimate goal is to simulate an ECU. But this is of course work in progress. The program responds on diagnostic code (B9F0), which delivers the part number, and software number.
(as a workaround for the openmoose mod) In the manual I put a download link for the DHA (diagnostic host application) software. This software works with the DICE cable, and allows to send diagnostic messages and (!) receive the response. It can open a database in DDB format, which is text that can be edited. I modified/simplified the existing database so it works with my Volvo (file volvoV50.DDB). Upon (Read Data Block By Offset/ECU identification) it interacts with my stm32 microcontroller, which fools the diagnostic software into dealing with a Volvo. (Volvos have never been cheaper ;)) ~
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 10uF / 6.3V | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C2, C3, C4, C7 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R2, R3, R4 |
| 4 | 59R / 1% | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R5, R6, R7, R8 |
| 4 | Jumper_3_Open | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1, JP2, JP3, JP4 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 2 | 330R | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R9, R10 |
| 2 | 4700pF / 50V | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C5, C6 |
| 2 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4, J5 |
| 2 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2 |
| 1 | AZ1117-3.3 | Package_TO_SOT_SMD:SOT-223 | U3 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Conn_ARM_JTAG_SWD_10 | Connector_TagConnect:Tag-Connect_TC2050-IDC-NL_2x05_P1.27mm_Vertical | J1 |
| 1 | MAX3051 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | STM32F091CBTx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |

CopperPilot/Jetson-AI-Cam-CopperPilot
A carrier for Jetson Nano, Xavier NX and TX2 NX with two IMX219 cameras on a 39 mm stereo baseline, dual 4K outputs and CAN.

myaki-moe/usb2can
A compact and low cost open source USB to CAN bus adaptor. 紧凑且低成本的开源USB到CAN总线适配器





alex31/smartprobe
firmware and hardware for an autonomous five holes 3D pitot tube

ay2718/RadomeMotorController
The Radome CAN protocol is very simple. Send azimuth commands to address 0x1 and elevation commands to address 0x2. Azimuth and elevation reply back from addresses 0x101 and 0x102 respectively.
It measures 53 × 36 mm and has 2 copper layers, 1.6 mm thick.
35 parts, built around the MAX3051EKA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the najnesnaj/moosesnif repository on GitHub, at the commit this page was made from: the board is stm32f103c6-canbus/hardware/controller.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask najnesnaj before reusing the design.