
Nucleo
nailed-barnacle/Cisc-8-ttl-processor
A cut-down version of the 8080 processor using HCTTL and including a discrete ALU and instruction decoder

A cut-down version of the 8080 processor using HCTTL and including a discrete ALU and instruction decoder
Cisc-8 is an open-source printed circuit board by nailed-barnacle, from the nailed-barnacle/Cisc-8-ttl-processor repository on GitHub, published under the MIT licence. It is a 2-layer board of 299.7 × 198.1 mm with 319 parts on 480 nets, routed with 17,052 tracks and 2,274 vias.
It is built around the 74HC541D, 74HC08D and 74HC574D, with the 74HC32D, 74HC4075D and 74HC238D among its other parts. Its parts include 159 ICs, 155 capacitors and 1 connector.
A cut-down version of the 8080 processor using HCTTL and including a discrete ALU and instruction decoder
This is an attempt to replicate most of the functionality of the 1970s Intel 8080 processor using contemporary HCTTL surface mount components.
By implementing most - though by no means all - of the instructions of the 8080 it allows the use of existing toolchains to generate code for the device both for the hardware implementation and the associated simulation.
The programmer's model is the same as the original 8080 - the following instructions are implemented (refer to an 8080 manual for details):
mov add adc sub sbb ana xra ora adi aci sui sbi ani xri ori sphl lxi dad lda sta mvi push pop jmp jnz jz jnc jc call ret
All other instructions are unimplemented. There are minor changes regarding push/pull, in that push writes to the stack pointer address and then decrements it (and pull increments it and then reads) while the 8080 decrements before pushing. Additionally, it is not possible to mvi to m (hl).
A single non-maskable interrupt is provided, with a hard call to 0x0008 at the end of the current instruction (reset starts at 0x0000)
A two-internal bus model is used, which approximately doubles the speed (in clock cycles) of the original 8080. The longest instruction is the call, which requires 7 cycles.
Provided here are Kicad files for the schematics, Bill of Materials, and the final 200x300mm PCB. The normal processor interface - data and address bus, power, clock etc are provided through a 40-pin header which would attach to an adjacent board providing memory, serial port etc.
Recommended for assembling 8080 code in the browser: https://svofski.github.io/pretty-8080-assembler/
| Qty | Value | Footprint | References |
|---|---|---|---|
| 155 | 100n | Capacitor_SMD:C_0603_1608Metric | C1001, C1002, C1003, C1004, C1101, C1102, C1103, C1201, C1202, C1203, C1204, C1205, C1206, C1207, C1301, C1401 +139 |
| 29 | 74HC08 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U1103, U1403, U1405, U1406, U1407, U1408, U1412, U1502, U1505, U1506, U1507, U1510, U1511, U1519, U1520, U1521 +13 |
| 21 | 74HC541 | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U304, U312, U315, U316, U321, U322, U323, U403, U502, U504, U601, U602, U603, U1002, U1003, U1004 +5 |
| 21 | 74HC574 | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U201, U202, U203, U204, U205, U206, U207, U208, U209, U210, U211, U212, U213, U214, U305, U505 +5 |
| 16 | 74HC32 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U307, U308, U310, U1404, U1411, U1413, U1501, U1509, U1516, U1518, U1602, U1702, U1804, U1901, U1904, U2102 |
| 12 | 74HC4075 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U313, U1416, U1503, U1504, U1508, U1517, U1703, U1801, U1802, U1903, U2103, U2108 |
| 11 | 74HC238 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U309, U1204, U1205, U1206, U1301, U1417, U1418, U1419, U1513, U1514, U1515 |
| 8 | 74HC00-74xx | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U2001, U2002, U2003, U2004, U2005, U2006, U2007, U2008 |
| 6 | 74HC283 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U319, U320, U607, U608, U609, U610 |
| 5 | 74HC163 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U501, U503, U506, U508, U901 |
| 5 | 74HC27 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U1102, U1414, U1707, U1806, U2107 |
| 4 | 74HC04 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U311, U1001, U1409, U1603 |
| 4 | 74HC11 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U1201, U1202, U1203, U1207 |
| 4 | 74HC157 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U402, U802, U1604, U1605 |
| 4 | Conn_01x01 | Mounting_Holes:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 74HC02 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U1402, U1523, U1705 |
| 3 | 74HC86 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U314, U317, U801 |
| 2 | 74HC00 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U1401, U1706 |
| 2 | 74HC74 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U401, U1101 |
| 1 | 74HC10 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U1708 |
| 1 | 74HC138 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U301 |
| 1 | 74HC4002 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U318 |
| 1 | Conn_02x20_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_Vertical_SMD | J2001 |

nailed-barnacle/Cisc-8-ttl-processor
A cut-down version of the 8080 processor using HCTTL and including a discrete ALU and instruction decoder


arhefner/1802-Mini-SPI-DMA
SPI Expansion Board for the 1802/Mini Computer

slu4coder/Minimal-64x4-Home-Computer
My DIY TTL home computer with VGA and PS/2 and 4x the processing power of a Commodore C64 or Apple II.



c0pperdragon/BreadBin
A CPU made of 7400 logic on breadboards - inside a bread bin ;-)


It measures 299.7 × 198.1 mm and has 2 copper layers, 1.6 mm thick.
319 parts, built around the 74HC541D, 74HC08D, 74HC574D and 74HC32D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the nailed-barnacle/Cisc-8-ttl-processor repository on GitHub, at the commit this page was made from: the board is cisc-8.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).