
DecodingBoard
N-Pulse/BMI-EMG-HW
Find the schematics and PCB layout for the hardware of the EMG Bracelet

Find the schematics and PCB layout for the hardware of the EMG Bracelet
Processing board is an open-source printed circuit board by N-Pulse, from the N-Pulse/BMI-EMG-HW repository on GitHub. It is a 2-layer board of 33.1 × 54 mm with 59 parts on 80 nets, routed with 309 tracks and 30 vias.
It is built around the STM32WBA65CIU6, DLF162500LT-5028A1 and TPS7A7200RGW, with the PMEG4030AEXE-QX, TL3305BF100QG and CONMHF1-SMD-G-T among its other parts. Its parts include 21 capacitors, 14 resistors, 6 diodes, 5 connectors and 2 ICs. It belongs with the STM32 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100nF | Capacitor_SMD:C_0402_1005Metric | C1, C2, C15, C16, C17, C18, C20, C21, C22, C26 |
| 6 | 100R | Resistor_SMD:R_0402_1005Metric | R1, R2, R5, R6, R8, R14 |
| 4 | PMEG4030AEXE-QX | PMEG4030AEXE-QX:PMEG4030AEXEQX | D2, D3, D4, D5 |
| 3 | 10k | Resistor_SMD:R_0402_1005Metric | R7, R11, R13 |
| 2 | 10pF | Capacitor_SMD:C_0603_1608Metric | C3, C4 |
| 2 | 10uF | Capacitor_SMD:C_0402_1005Metric | C25, C27 |
| 2 | 4.7k | Resistor_SMD:R_0603_1608Metric | R3, R4 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R9, R10 |
| 2 | DMP3056LSS-13 | DMP3056LSS-13:SOIC127P600X170-8N | Q1, Q2 |
| 2 | IN_S42BT LED | LED_SMD:LED_0402_1005Metric | D1, D6 |
| 2 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2 |
| 2 | TL3305BF100QG | TL3305BF100QG:TL3305BF160QG | SW1, SW2 |
| 1 | 0.3pF | Capacitor_SMD:C_0402_1005Metric | C29 |
| 1 | 0.8pF | Capacitor_SMD:C_0402_1005Metric | C28 |
| 1 | 100p | Capacitor_SMD:C_0603_1608Metric | C5 |
| 1 | 1uF | Capacitor_SMD:C_0402_1005Metric | C19 |
| 1 | 2.2uH | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | 2.7nH | Inductor_SMD:L_0402_1005Metric | L2 |
| 1 | 4.7u | Capacitor_SMD:C_0402_1005Metric | C6 |
| 1 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C24 |
| 1 | 470nF | Capacitor_SMD:C_0402_1005Metric | C23 |
| 1 | 86.6k | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | CONMHF1-SMD-G-T | CONMHF1-SMD-G-T:CONMHF1SMDGT | J11 |
| 1 | CX2016DB32000D0FLJCC | CX2016DB32000D0FLJCC:xtal4_CX2016DB_AVX | XTAL1 |
| 1 | Conn_01x03_Pin | Connector_JST:JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | 5V |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical_SMD_Pin1Left | J4 |
| 1 | Conn_01x04_Pin | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J1 |
| 1 | Conn_01x06_Pin | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical_SMD_Pin1Left | J3 |
| 1 | DLF162500LT-5028A1 | DLF162500LT-5028A1:DLF162500LT5028A1 | FL1 |
| 1 | STM32WBA65CIU6 | STM32:QFN50P700X700X60-49N-D | IC1 |
| 1 | TPS7A7200RGW | Package_DFN_QFN:Texas_RGW0020A_VQFN-20-1EP_5x5mm_P0.65mm_EP3.15x3.15mm_ThermalVias | U1 |
| 1 | USB4215-03-A_REVA | USB4215_03_A:GCT_USB4215-03-A_REVA | J8 |

N-Pulse/BMI-EMG-HW
Find the schematics and PCB layout for the hardware of the EMG Bracelet

N-Pulse/BMI-EMG-HW
Find the schematics and PCB layout for the hardware of the EMG Bracelet

N-Pulse/BMI-EMG-HW
Find the schematics and PCB layout for the hardware of the EMG Bracelet

N-Pulse/BMI-EMG-HW
Find the schematics and PCB layout for the hardware of the EMG Bracelet

N-Pulse/EMG-HW-MainBoard
This repository contains the PCB design of the EMG bracelet's main board used for EMG signal processing and decoding. Detailed description of the project can be found in the Documentation folder

timohueser/OpenBikeComputer
Open source Bikecomputer with a focus on exploration and adventure.

manhoosbilli1/smart-cube-multi-pcb-flex-assembly
Smart Cube - multi-PCB flex assembly (PCBA, PCBB, PCBC + FLEX + tabs Y/G/B)

Ribbit-Network/ribbit-network-frog-hardware
The sensor for the world's largest crowdsourced network of open-source, low-cost, GHG Gas Detection Sensors.

Maritime-Hacking-Village/Badge-2025
Public repository for the official MHV 2025 badge.

fiskebolle30/Bachelor_Electronics_hardware
All PCB design files for the bachelor project. Project is made in KiCad


It measures 33.1 × 54 mm and has 2 copper layers, 1.16 mm thick.
59 parts, built around the STM32WBA65CIU6, DLF162500LT-5028A1, TPS7A7200RGW and PMEG4030AEXE-QX. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the N-Pulse/BMI-EMG-HW repository on GitHub, at the commit this page was made from: the board is DecodingBoard/Board V3/Processing_board.kicad_pcb and its schematic BioAmps/BioAmp_V1/BioAmp-EXG-Pill.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask N-Pulse before reusing the design.