Skip to the content
4 layers39.8 × 44 mmConnecteur, the printed circuit board in 3D

Microcontroller : A STM32G484 optimized for mixed-signal applications with a 16MHz external oscillator. Control the 8 DC motors independently. Power Management : +12V supply +5V supplied from the Power Board.

Size
39.8 × 44 mm
Copper layers
4
Thickness
1.6 mm
Parts
75
Nets
44
Pads
129
Tracks, vias
180, 0
Pours
4
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
29 Oct 2024
Updated
8 May 2025

Overview

Connecteur is an open-source printed circuit board by N-Pulse, from the N-Pulse/ARM-ELEC-CTRL repository on GitHub, published under the CC-BY-4.0 licence. It is a 4-layer board of 39.8 × 44 mm with 75 parts on 44 nets, routed with 180 tracks and 0 vias.

README

NPulse_v4/README.md

N-Pulse - Control Board

Key Features

  • Microcontroller: A STM32G484 optimized for mixed-signal applications with a 16MHz external oscillator. Control the 8 DC motors independently.
  • Power Management: +12V supply +5V supplied from the Power Board. Use of a LDO to convert +5V to +3.3V ensuring a clean and independent +3.3V on the board.
  • 8 motor drivers: DRV8220 (TI) 2 Half-side bridges control with a 4-NOR-Gates SNLVC7402 with a PWM and a digital inputs
  • 6 10 positions connectors: link between the control board and the "connector board" on which all wires are solder (Power supply, FSR - Force sensor resistor, Motors + encoders)

Points that need to be reviewed

  1. Schematic - All the pins of the MCU : Check in the datasheet that all signals (PWM, Analogic (FSRs, LED, VBat, currents), encoders, oscillators, UARTs, SPI, reset, debug) are connected to the good MCU pins. So, the properties and the timers of each MCU must be checked.
  2. PCB - Footprint of each components (Daniel is working on that) : Check that all the selected footprints are the same as those described in datasheets.

Parts

75
QtyValueFootprintReferences
66Conn_01x01Connector_Wire:SolderWire-0.1sqmm_1x01_D0.4mm_OD1mmJ1, J2, J11, J12, J14, J15, J16, J17, J18, J19, J20, J21, J22, J23, J25, J26 +50
6Conn_02x05_Odd_EvenConnector_PinSocket_2.00mm:PinSocket_2x05_P2.00mm_Vertical_SMDJ10, J13, J32, J35, J54, J57
3MountingHoleMountingHole:MountingHole_2.2mm_M2H1, H2, H3

More from N-Pulse/ARM-ELEC-CTRL

2
  • 4 layers39.8 × 72.5 mmNPulse v4, the printed circuit board in 3D

    NPulse v4

    N-Pulse/ARM-ELEC-CTRL

    Microcontroller : A STM32G484 optimized for mixed-signal applications with a 16MHz external oscillator. Control the 8 DC motors independently. Power Management : +12V supply +5V supplied from the Power Board.

    163 partsCC-BY-4.0
  • 4 layers38 × 119.5 mmNPulse v3, the printed circuit board in 3D

    NPulse v3

    N-Pulse/ARM-ELEC-CTRL

    Microcontroller : A STM32G484 optimized for mixed-signal applications with a 16MHz external oscillator. Control the 8 DC motors independently. Power Management : +12V supply +5V supplied from the Power Board.

    162 partsCC-BY-4.0

Similar boards

  • 4 layers46 × 46 mmBLDC DriverV1, the printed circuit board in 3D

    BLDC DriverV1

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    75 parts915
  • 4 layers30 × 30 mmReCamera 2002 POE Board, the printed circuit board in 3D

    ReCamera 2002 POE Board

    Seeed-Studio/OSHW-reCamera-Series

    reCamera is a series of open-source AI cameras.

    75 parts495Apache-2.0
  • 4 layers52.5 × 46.5 mmBoard latest, the printed circuit board in 3D

    Board latest

    dennisss/dacha

    Monorepo for awesome tools/projects/libraries

    75 parts397Apache-2.0
  • 4 layers100 × 68 mmBasic ecp5-pcb, the printed circuit board in 3D

    Basic ecp5-pcb

    mattvenn/basic-ecp5-pcb

    Reference design for Lattice ECP5 FPGA. Featuring Raspberry Pi interface and 6 PMODs

    75 parts144CC0-1.0
  • 4 layers49.5 × 54.9 mmOSSI CM1, the printed circuit board in 3D

    OSSI CM1

    transistorgrab/OSSI

    Open Source Solar Inverter - Software, Hardware, Mechanics

    75 parts99MIT
  • 4 layers30 × 30 mmWiSer TTL, the printed circuit board in 3D

    WiSer TTL

    bitmerse/WiSer

    WiSer: Bringing wireless convenience to serial connectivity

    75 parts52
  • 4 layers100 × 49.8 mmExpansion board, the printed circuit board in 3D

    Expansion board

    reubenstr/zuko

    A quadruped robot dog!

    75 parts51MIT
  • 4 layers80.7 × 65.8 mmPico hx, the printed circuit board in 3D

    Pico hx

    dan-rodrigues/pico-hx

    PCB combining Raspberry Pi Pico and iCE40 FPGA

    75 parts31

Questions

How big is the Connecteur PCB?

It measures 39.8 × 44 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Connecteur use?

75 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Connecteur KiCad files?

From the N-Pulse/ARM-ELEC-CTRL repository on GitHub, at the commit this page was made from: the board is NPulse_v4/connecteur/connecteur.kicad_pcb and its schematic NPulse_v2/COM_EMG.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Connecteur design in my own project?

Its repository publishes it under the CC-BY-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).