Skip to the content
4 layers60 × 40 mmPoe trigger, the printed circuit board in 3D

802.3af / 802.3at PoE trigger board

Size
60 × 40 mm
Copper layers
4
Thickness
1.6 mm
Parts
25
Nets
34
Pads
95
Tracks, vias
253, 54
Pours
3
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
5 Aug 2026
Updated
5 Aug 2026

Overview

Poe trigger is an open-source printed circuit board by msaribekyan, from the msaribekyan/cobalt-poe-trigger repository on GitHub. It is a 4-layer board of 60 × 40 mm with 25 parts on 34 nets, routed with 253 tracks and 54 vias.

It is built around the TPS2378DDA, ABS10 and 30F-51NL, with the SMAJ58A among its other parts. Its parts include 7 resistors, 4 diodes, 4 connectors, 3 capacitors and 1 IC.

Main components

4

README

README.md

Cobalt PoE Trigger

Open source 802.3af/802.3at trigger board

The board is designed to negotiate with 802.3af and 802.3at PoE injectors and output stable 48V DC power.

assembled board

Schematic

The board uses the TPS2378 IC from Texas Instruments. The ethernet transformer is placed between the input and output ethernet jacks. Center taps from the PoE side are used for PoE classification and power transfer, while the other side uses the Bob Smith termination. An indicator LED shows when the negotiations are successful.

schematic

PCB

The dimensions of the board are 60mm x 40mm, with 4 x M3 mounting holes in the corners. A 4 layer stackup is selected, with 2 inner ground layer. Top layer is used for signal routing. Ethernet differential pairs have controlled impedance of 100 ohms, are length matched and routed using the differential pair routing tool in KiCad. JST VH 3.96mm connector is used for power output.

layout

Fabrication

PCB is ordered from JLCPCB with the 4 layer JLC04161H-7628 stackup. Parts are ordered from LCSC. Below is the bill of materials:

Part NumberQuantityLCSC NumberDescription
RJ-055-12C7205195RJ45 jack
30F-51NL1C123168LAN Magnetics
RS-03K750JT4C140070Resistor 75R
1206B102K202NT1C9196Capacitor 1nF 2kV
TPS2378DDAR1C337500PoE PD IC
ABS10A-132C442622Bridge rectifier
CL31B104KCFNNNE1C1945Capacitor 100nF 100V
SMAJ58A1C151246TVS Diode
FRC0402F2492TS1C2998048Resistor 24.9k
FRC0402F63R4TS1C3013183Resistor 63.4R
RT1J220M06071C267472Capacitor 22uF
B2P-VH-FB-B(LF)(SN)2C1580063.96mm 2 pin connector
ERJ-UP3J223V1C1870044Resistor 22k 0.25W
XL-1608UYC-061C965802LED Yellow

Testing

The PCB is tested with gigabit ethernet switches and an Ubiquiti PoE injector. The board is able to provide stable 48V power and maintain gigabit speeds between the test equipment.

Parts

25
QtyValueFootprintReferences
475RResistor_SMD:R_0603_1608MetricR3, R4, R5, R6
4M3MountingHole:MountingHole_3.2mm_M3_ISO7380_PadH1, H2, H3, H4
2ABS10Diode_SMD:Diode_Bridge_Diotec_ABSD1, D2
2Conn_01x02Connector_JST:JST_VH_B2P-VH-FB-B_1x02_P3.96mm_VerticalJ3, J4
1100nFCapacitor_SMD:C_1206_3216MetricC1
11nFCapacitor_SMD:C_1206_3216MetricC2
122kResistor_SMD:R_0603_1608MetricR7
122uFCapacitor_SMD:C_Elec_6.3x7.7C3
124.9kResistor_SMD:R_0402_1005MetricR1
130F-51NLTransformer_SMD:Transformer_Ethernet_YDS_30F-51NL_SO-24_7.1x15.1mmTR1
163.4RResistor_SMD:R_0402_1005MetricR2
1DataCustom:RJ-055-1J2
1LOGOCustom:cobalt_logoG***
1OrangeLED_SMD:LED_0603_1608MetricD4
1PoE + DataCustom:RJ-055-1J1
1SMAJ58ADiode_SMD:D_SMAD3
1TPS2378DDACustom:SOIC127P600X170-9NIC1

Similar boards

  • 2 layers123 × 91.6 mmMatt poe prototype, the printed circuit board in 3D

    Matt poe prototype

    mhardeman/matt-poe-prototype

    PoE Powered Device (PD) Prototype Schematic & PCB design in KiCad for 12V & 5V output rails

    56 parts5
  • 4 layers88.9 × 79.4 mmLink, the printed circuit board in 3D

    Link

    oats-center/avena-rs

    Avena On The Road: Bringing pavement health data to your fingertips

    170 parts3
  • 4 layers70 × 100 mmSTM32POE, the printed circuit board in 3D

    STM32POE

    KunoDLK/POE-Test

    114 parts
  • 4 layers68.6 × 21 mmPico poe, the printed circuit board in 3D

    Pico poe

    rm-1n/conduit

    poe microcontroller with web IDE + firmware upload

    76 partsMIT
  • 4 layers82.5 × 65.5 mmOpenHomeSwitch, the printed circuit board in 3D

    OpenHomeSwitch

    TobleMiner/OpenHomelabSwitch

    297 parts11
  • 4 layers150.2 × 105 mmAlexandria ng, the printed circuit board in 3D

    Alexandria ng

    bence98/LibreEther

    Free and open source networking devices

    91 parts2
  • 4 layers128.5 × 40 mmScalenode cm4-baseboard, the printed circuit board in 3D

    Scalenode cm4-baseboard

    antmicro/scalenode-cm4-baseboard

    Baseboard for Raspberry Pi 4 Compute Module optimized for clustering

    146 parts152Apache-2.0
  • 2 layers194 × 114.1 mmPowermetering, the printed circuit board in 3D

    Powermetering

    Sync-/powermetering

    ADE9000 application circuit based power meter

    200 parts33

Questions

How big is the Poe trigger PCB?

It measures 60 × 40 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Poe trigger use?

25 parts, built around the TPS2378DDA, ABS10, 30F-51NL and SMAJ58A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Poe trigger KiCad files?

From the msaribekyan/cobalt-poe-trigger repository on GitHub, at the commit this page was made from: the board is src/poe_trigger.kicad_pcb and its schematic src/poe_trigger.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Poe trigger design in my own project?

Its repository states no licence, so its author keeps all rights: ask msaribekyan before reusing the design.