2 layers82.2 × 101.3 mm
2 layers165 × 70 mm
Ev charger met16
ms270169/kicad1) Voltage transformer module does not work Wrong operation amplifier on module (OP07C instead of LM358) PCB error on R3 (see netlist-reverse-engieneered.jpg)
- Size
- 165 × 70 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 70
- Nets
- 61
- Pads
- 253
- Tracks, vias
- 544, 41
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 12 May 2018
- Updated
- 12 May 2018
Overview
Ev charger met16 is an open-source printed circuit board by ms270169, from the ms270169/kicad repository on GitHub, published under the MIT licence. It is a 2-layer board of 165 × 70 mm with 70 parts on 61 nets, routed with 544 tracks and 41 vias.
It is built around the HLK-PM01, MMBF170 and NTR2101P. Its parts include 28 resistors, 10 connectors, 6 capacitors, 6 diodes and 5 ICs. It belongs with the power boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
3
HLK-PM01
DIP,34x24mm0.1W 100mVp-p 15mm 20mm 34mm 3W 3kV 5V 700mA 73% 85VAC~265VAC AC-DC Short Circuit Protection、Over Current Protection、Fault self-recovery ±0.2% 插件,34x20mm AC-DC Power Modules ROHSHI-LINKAC-DC Power Modules
MMBF170
SOT-23-55℃~+150℃ 1 N-channel 11pF 2.1V 2.2Ω@10V 200mA 22pF 2pF 300mW 60V SOT-23 MOSFETs ROHSDiodes IncorporatedMOSFETsNTR2101P
SOT-23-55℃~+150℃ 1 P-Channel 1.173nF 120mΩ@1.8V 15nC@4.5V 1V 218pF 289pF 3.7A 8V 960mW P-Channel SOT-23 MOSFETs ROHSonsemiMOSFETs
README
ev-charger-met16/README.mdev-charger-met16
History
V0.1: Schematic and Layout finished
| Topic | Description |
|---|---|
| Commit | 3cf1186470543ce20f478d2e2e48a76af5a9076f |
| Status | Design finished |
| Manufactured | No |
| Tested | No |
| Issue 1 | 230V Voltage transformer module ebay 232542976388 not working |
Issues
-
Voltage transformer module does not work
- Wrong operation amplifier on module (OP07C instead of LM358)
- PCB error on R3 (see netlist-reverse-engieneered.jpg)
Voltage between
OUT-GNDhas only a amplitude maximum of 15mV arround 0V.
Parts
70| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 0R | Resistors_SMD:R_1206_HandSoldering | R11, R16, R18, R23, R24 |
| 5 | 10k | Resistors_SMD:R_1206_HandSoldering | R2, R3, R10, R13, R26 |
| 4 | 100n | Capacitors_SMD:C_1206_HandSoldering | C3, C4, C5, C6 |
| 3 | 1k | Resistors_SMD:R_1206_HandSoldering | R5, R6, R9 |
| 3 | D_Schottky | Diodes_SMD:D_SOD-323_HandSoldering | D1, D4, D5 |
| 2 | 15k | Resistors_SMD:R_1206_HandSoldering | R1, R22 |
| 2 | 2k7 | Resistors_SMD:R_1206_HandSoldering | R14, R15 |
| 2 | 33k | Resistors_SMD:R_1206_HandSoldering | R4, R17 |
| 2 | 3k3 | Resistors_SMD:R_1206_HandSoldering | R12, R25 |
| 2 | Conn_01x03 | Pin_Headers:Pin_Header_Straight_1x03_Pitch2.54mm | J2, J9 |
| 2 | Conn_01x15 | Pin_Headers:Pin_Header_Straight_1x15_Pitch2.54mm | J3, J4 |
| 2 | MMBF170 | TO_SOT_Packages_SMD:SOT-23_Handsoldering | Q2, Q4 |
| 2 | NTR2101P | TO_SOT_Packages_SMD:SOT-23_Handsoldering | Q1, Q3 |
| 1 | 1.3k | Resistors_SMD:R_1206_HandSoldering | R28 |
| 1 | 100k | Resistors_SMD:R_1206_HandSoldering | R20 |
| 1 | 10K | Potentiometers:Potentiometer_Trimmer_Bourns_3299W | RV1 |
| 1 | 12k | Resistors_SMD:R_1206_HandSoldering | R8 |
| 1 | 1n | Capacitors_SMD:C_1206_HandSoldering | C2 |
| 1 | 1u | Capacitors_SMD:C_1210_HandSoldering | C1 |
| 1 | 2.74k | Resistors_SMD:R_1206_HandSoldering | R27 |
| 1 | 2k2 | Resistors_SMD:R_1206_HandSoldering | R19 |
| 1 | 39k | Resistors_SMD:R_1206_HandSoldering | R21 |
| 1 | 47k | Resistors_SMD:R_1206_HandSoldering | R7 |
| 1 | ACS712 | Housings_SOIC:SO-8_5.3x6.2mm_Pitch1.27mm | U4 |
| 1 | ARDUINO-NANO | MyFootprints:Arduino-Nano | U1 |
| 1 | Conn_02x02_Counter_Clockwise | Pin_Headers:Pin_Header_Straight_2x02_Pitch2.54mm | J10 |
| 1 | D_Schottky | Diodes_SMD:D_SMA-SMB_Universal_Handsoldering | D6 |
| 1 | HLK-PM01 | MyFootprints:HLK_PM01 | U2 |
| 1 | LCD-Sure | MyFootprints:LCD-Sure-shifted-064 | J7 |
| 1 | Lusterklemme-6mm2-40A | MyFootprints:Lusterklemme-PA30P-6mm2-40A-x3-N | J5 |
| 1 | Lusterklemme-6mm2-40A | MyFootprints:Lusterklemme-PA30P-6mm2-40A-x3-S | J6 |
| 1 | SW_DPDT_x2 | MyFootprints:SW-ebay-171865305033 | SW2 |
| 1 | SW_PT65-501 | MyFootprints:SW_DIP_x3_W7.62mm_PT65-501 | SW1 |
| 1 | Screw_Terminal_01x02 | MyFootprints:Terminalblock-2x-5mm | J1 |
| 1 | UART-Harwin4 | Connectors_Harwin:Harwin_LTek-Male_04x2.00mm_Straight_StrainRelief | J8 |
| 1 | ebay-232542976388 | MyFootprints:ebay-232542976388 | U5 |
| 1 | ebay-253052736386 | MyFootprints:ebay-253052736386 | U3 |
| 1 | grün | LEDs:LED_PLCC-2 | D3 |
| 1 | rot | LEDs:LED_PLCC-2 | D2 |
The 62 most common of 70 parts.
Similar boards
- 2 layers90 × 50 mm
USB Hub V2.0
CarosCave/4_Port_2.0_USB-Hub
You will find the: - CAD-Files in the folder KiCAD - The manufacturing files in the folder Gerber-files - The PDF documents in the folder PDF - The licence files from CERN OHL v. 1.2 under Licence
62 parts2 - 2 layers
- 2 layers65 × 65.1 mm
Base heating
NerdyProjects/HouseBusNode
(Yet another) house bus hardware based on STM32F072 and the CAN bus
90 parts8 - 2 layers156 × 116 mm
- 4 layers50 × 35 mm
- 2 layers14 × 14 mm
Try2
SKGleba/psp2sdboot
Tools and guides for achieving code execution in Playstation Vita/TV BootROM's "SD boot mode"
10 parts51MIT - 2 layers72 × 22 mm
Cheating calc
ChinesePrince07/TI-84-GPT-HACK
A mod that gives your TI-84 Wi-Fi, ChatGPT, and the ability to disappoint your math teacher in ways never thought possible. Original idea by Chromalock, reconstructed by myself after his repo is taken down.
8 parts9GPL-3.0
Questions
How big is the Ev charger met16 PCB?
It measures 165 × 70 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Ev charger met16 use?
70 parts, built around the HLK-PM01, MMBF170 and NTR2101P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Ev charger met16 KiCad files?
From the ms270169/kicad repository on GitHub, at the commit this page was made from: the board is ev-charger-met16/ev-charger-met16.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Ev charger met16 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).