
SMT stopper
mrkubag/SMT_stopper
Projekt sterownika automatycznie regulowanego stopera wbudowanego w transporter PCB.

Projekt sterownika automatycznie regulowanego stopera wbudowanego w transporter PCB.
SMT stopper.kicad pcb DCDC is an open-source printed circuit board by mrkubag, from the mrkubag/SMT_stopper repository on GitHub. It is a 2-layer board of 80 × 80 mm with 73 parts on 86 nets, routed with 338 tracks and 17 vias.
It is built around the CH340N, LM2596S-12 and AMS1117-3.3, with the MMBT3904, SS310 and AO3407A among its other parts. Its parts include 20 resistors, 19 capacitors, 10 connectors, 9 ICs and 5 diodes. It belongs with the power boards and the STM32 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100nF | Capacitor_SMD:C_0805_2012Metric | C6, C7, C8, C9, C10, C11, C12 |
| 4 | PC817 | Zlacza:SMDIP-4_W7.62mm_poprawiony | U2, U5, U6, U8 |
| 3 | 0.22uF | Capacitor_SMD:C_0805_2012Metric | C13, C14, C15 |
| 3 | 10K | Resistor_SMD:R_0805_2012Metric | R9, R10, R15 |
| 3 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R2, R20 |
| 3 | 12K | Resistor_SMD:R_0805_2012Metric | R13, R16, R17 |
| 3 | 220R | Resistor_SMD:R_0805_2012Metric | R11, R12, R14 |
| 3 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3 |
| 3 | SS310 | Diode_SMD:D_SMB_Handsoldering | D3, D5, D6 |
| 2 | 1.5K | Resistor_SMD:R_0805_2012Metric | R3, R4 |
| 2 | 1000pF | Capacitor_SMD:C_0805_2012Metric | C16, C17 |
| 2 | 20pF | Capacitor_SMD:C_0805_2012Metric | C4, C5 |
| 2 | 22uF | Capacitor_SMD:C_0805_2012Metric | C21, C22 |
| 2 | 250m | Resistor_SMD:R_1206_3216Metric | R5, R6 |
| 2 | 47K | Resistor_SMD:R_0805_2012Metric | R7, R8 |
| 2 | 680uF | Capacitor_SMD:C_Elec_10x10.2 | C19, C20 |
| 1 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C18 |
| 1 | 16Mhz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric | R18 |
| 1 | 2k2 | Resistor_SMD:R_0805_2012Metric | R19 |
| 1 | 3V3 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | 68uH | Zlacza:YSPI1050 | L2 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U9 |
| 1 | AO3407A | Package_TO_SOT_SMD:SOT-23 | Q4 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | CH340N | Package_SO:SOP-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | CX-442 | Zlacza:WJ500V_3P | J10 |
| 1 | Conn_01x04_Male | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | KRANCOWKA | Zlacza:WJ500V | J9 |
| 1 | LASER | Zlacza:WJ500V | J4 |
| 1 | LM2596S-12 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U7 |
| 1 | Relay LASER | Zlacza:Relay | K2 |
| 1 | Relay SMEMA | Zlacza:Relay | K1 |
| 1 | SMEMA | Zlacza:WJ500V | J5 |
| 1 | SOLENOID | Zlacza:WJ500V | J2 |
| 1 | STATUS | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 1 | STEPPER_A | Zlacza:WJ500V | J7 |
| 1 | STEPPER_B | Zlacza:WJ500V | J8 |
| 1 | STM32F103CBTx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | SW_DIP_x02 | Button_Switch_THT:SW_DIP_SPSTx02_Slide_6.7x6.64mm_W7.62mm_P2.54mm_LowProfile | SW1 |
| 1 | USB_B | Connector_USB:USB_B_Lumberg_2411_02_Horizontal | J1 |
| 1 | ZASILANIE | Zlacza:WJ500V | J6 |
| 1 | ~ | Package_SO:HTSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.75x6.2mm_ThermalVias | U4 |

mrkubag/SMT_stopper
Projekt sterownika automatycznie regulowanego stopera wbudowanego w transporter PCB.

xuejun7777/Comprehensive-Design-and-Practice-Project-A---Digital-Thermometer-Based-on-NTC
综合设计与实践A项目-基于NTC的数字温度计


Larryhul/periodic-signal-analyzer
STM32G474 periodic signal analyzer: FFT harmonic measurement (Upp/Urms/fundamental/spectrum), OPA2365 front end, KiCad PCB, firmware & dashboard. 2026 Shanghai electronic design contest, Problem G. 周期信号测量分析装置

alcaaron/esi_project
ENGINYERIA DE SISTEMES: PROJECTE DE CURS Fet per - Aaron Alcalá - Albert Bombí - Marcos García

HexFud/Bench-power-supply
I designed a simple and cost effective bench power supply for everyone. To simplify the assmebly process i designed in kicad a small pcb where you connect external components


TCC-Sumo-Telemetria/Eletronica_Sumo_Telemetria
Projetos eletrônicos relacionados ao trabalho de conclusão de curso "SISTEMA DE TELEMETRIA PARA A AVALIAÇÃO DE DESEMPENHO DE UM ROBÔ DE MEGA SUMÔ AUTÔNOMO".

It measures 80 × 80 mm and has 2 copper layers, 1.6 mm thick.
73 parts, built around the CH340N, LM2596S-12, AMS1117-3.3 and MMBT3904. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the mrkubag/SMT_stopper repository on GitHub, at the commit this page was made from: the board is SMT_stopper/SMT_stopper.kicad_pcb_DCDC.kicad_pcb and its schematic SMT_stopper/SMT_stopper.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask mrkubag before reusing the design.