Skip to the content
2 layers41.9 × 31.1 mmEGA Mono Composite Converter, the printed circuit board in 3D

EGA Mono Composite Converter

monotech/EGA-Mono-Composite-Converter9

Convert EGA to Monochrome-Composite. Good for IBM 5155 and EGA card.

Size
41.9 × 31.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
18
Nets
18
Pads
91
Tracks, vias
137, 0
Pours
35
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
15 Mar 2020
Updated
28 Aug 2022

Overview

EGA Mono Composite Converter is an open-source printed circuit board by monotech, from the monotech/EGA-Mono-Composite-Converter repository on GitHub. It is a 2-layer board of 41.9 × 31.1 mm with 18 parts on 18 nets, routed with 137 tracks and 0 vias.

Its parts include 10 resistors, 2 capacitors, 2 ICs, 2 connectors and 1 transistor.

README

README.md

Based on Hugo Holden's "FITTING AN EGA CARD TO AN IBM 5155" from 2016.

This plugs onto an EGA card's feature connector, such as the IBM EGA card.

It adds a crystal clear monochrome composite output in two places, untainted by the colour subcarrier.

  • One internal 4-pin header, meant for the IBM 5155's internal amber CRT, which takes a standard composite video input.

  • And one at the rear of the EGA card, on one of the usually unconnected RCA jacks.

    • The rear RCA jack output only applies to cards that have this RCA jack connected to the feature connector (P1 on the IBM EGA card: the top RCA jack).

You must set the card to CGA-compatible mode. If the card tries to output EGA-Hi-Res modes, the composite output will be unsupported by most monitors.

Simplified the schematic to reduce BoM and board size.

There is no longer provision for expanding the schematic to add colour-composite.

BoM:

DesignationPart
U1, U274HCT86
Q12N3904
C14.7 to 10μF
C2100nF
P12x16 2.54mm male pin header
P21x4 2.54mm male right-angle pin header
R175Ω
R2, R320Ω
R4360Ω
R5110Ω
R6680Ω
R7470Ω
R82kΩ
R94.3kΩ
R101kΩ
  • All parts are through-hole.
  • U1 and U2 can be replaced by 74, 74LS, 74S, 74F, 74ACT.
  • U2 can be replaced with a 74HCT32 - it will work the same.
  • Q1 can be replaced with most general purpose NPN transistors - beware of pinout.
  • Resistor tolerances can be 5% or less.
  • R2 is only needed for the internal 4-pin header output, intended for IBM 5155.
  • R3 is only needed for the rear RCA-jack output (P1 on IBM EGA card).

Parts

18
QtyValueFootprintReferences
220Custom KiCad Library:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2, R3
2HCT86Custom KiCad Library:DIP-14_W7.62mmU1, U2
1104Custom KiCad Library:C_Axial_L3.8mm_D2.6mm_P7.50mm_HorizontalC2
1110Custom KiCad Library:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR5
11kCustom KiCad Library:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR10
12kCustom KiCad Library:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR8
1360Custom KiCad Library:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR4
13904Package_TO_SOT_THT:TO-92_Inline_WideQ1
1470Custom KiCad Library:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR7
1475Custom KiCad Library:C_Disc_D4.3mm_W1.9mm_P5.00mmC1
14k3Custom KiCad Library:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR9
1680Custom KiCad Library:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR6
175Custom KiCad Library:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1
1< Mono Composite OutputConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_HorizontalP2
1IBM EGA Feature ConnectorConnector_PinSocket_2.54mm:PinSocket_2x16_P2.54mm_VerticalP1
1SYM_Arrow45_LargeCustom KiCad Library:Monotech Logo 12mmLOGO1

Similar boards

  • 2 layers27.9 × 16.5 mmPowerSSO-24 breakout, the printed circuit board in 3D

    PowerSSO-24 breakout

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    18 parts1.2k
  • 2 layers42.7 × 13.7 mmStm32-mini12864, the printed circuit board in 3D

    Stm32-mini12864

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    18 parts1.1kGPL-3.0
  • 2 layers41.2 × 46.6 mmThumb cluster left, the printed circuit board in 3D

    Thumb cluster left

    JesusFreke/lalboard

    A 3D-printed keyboard inspired by the DataHand

    18 parts993
  • 2 layers44 × 51.3 mm4272MAVcoder R4, the printed circuit board in 3D

    4272MAVcoder R4

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    18 parts915
  • 2 layers28.3 × 14.3 mmTap Photosensor PCB, the printed circuit board in 3D

    Tap Photosensor PCB

    VoronDesign/Voron-Tap

    Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:

    18 parts716GPL-3.0
  • 2 layers20.3 × 15.2 mmL0 stepper driver, the printed circuit board in 3D

    L0 stepper driver

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    18 parts546MIT
  • 2 layersMooltipass, the printed circuit board in 3D

    Mooltipass

    limpkin/mooltipass

    Github repository dedicated to the mooltipass project

    18 parts531
  • 2 layers42.5 × 28.8 mmC5VRX JACK DIY V2, the printed circuit board in 3D

    C5VRX JACK DIY V2

    Twotoz/C5VRX

    Ultra-minimal, zero-CPU 5.8 GHz analog FPV video receiver using ESP32-C5 Wi-Fi 6 PHY MODEM_DIAG, BitScrambler WBFM demodulation & resistor DAC CVBS

    18 parts515GPL-3.0

Questions

How big is the EGA Mono Composite Converter PCB?

It measures 41.9 × 31.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the EGA Mono Composite Converter use?

18 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the EGA Mono Composite Converter KiCad files?

From the monotech/EGA-Mono-Composite-Converter repository on GitHub, at the commit this page was made from: the board is EGA Mono Composite Converter.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the EGA Mono Composite Converter design in my own project?

Its repository states no licence, so its author keeps all rights: ask monotech before reusing the design.