

I've made GPS amplifier for hobby time, it failed. I've learned what I should not have done again to prevent failure. My motivation for doing this was to see the GPS signal spectrum. :)
- Size
- 82.5 × 87.9 mm
- Copper layers
- 4
- Thickness
- 1.64 mm
- Parts
- 85
- Nets
- 52
- Pads
- 308
- Tracks, vias
- 212, 365
- Pours
- 64
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 8 Sep 2025
- Updated
- 8 Sep 2025
Overview
Alm is an open-source printed circuit board by mohammadsdtmnd, from the mohammadsdtmnd/How-to-not-fail-RF-PCB-prototype repository on GitHub. It is a 4-layer board of 82.5 × 87.9 mm with 85 parts on 52 nets, routed with 212 tracks and 365 vias.
It is built around the TPS62933DRL, SF1186E-2 and AP7384-33Y, with the BNX028-01 among its other parts. Its parts include 35 capacitors, 14 inductors, 13 ICs, 5 connectors and 3 resistors. It belongs with the audio and music and radio and wireless boards of this library.
Main components
4TPS62933DRL
SOT-583-40℃~+150℃@(TJ) 1 12uA 2.2MHz 3.8V~30V 3A 800mV~22V Adjustable Buck Buck Built-in Yes SOT-583 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersSF1186E-2
SMD-40℃~+95℃ 1.57542GHz 15.3MHz 3.5dB 50Ω SMD SAW Filters ROHSMurataSAW FiltersAP7384-33Y
SOT-89-40℃~+125℃@(Tj) 1 2.5uA 3.3V 40V 500mV@(50mA) 50mA 60dB Fixed Positive Short Circuit Protection、Thermal Shutdown SOT-89 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsBNX028-01
FILTER-SMDFILTER-SMD New Arrivals ROHSMurataUncategorised
README
README.mdHow to not fail RF PCB prototype
I've made GPS amplifier for hobby time, it failed. I've learned what I should not have done again to prevent failure. My motivation for doing this was to see the GPS signal spectrum. :) Note I had tried my best to minimize cost. For example by eliminating stensil and soldermask. Though still PCB is metalized with bot layer gnd. I think I could also not making it metalized. Making it stiching with thin wire, instead. Since metalizing caused my manufacturer to prolong a long time.
You can look at schematic and PCB and see these strength:
- Simple
- High gain
- Extremely compact design
- 0.25mm PCB thickness chosen to decrease track and match them to RF amps
- small footprint which also causes them to be more stable because of less leakage
This compact design chosen to minimize distortion in GPS RF signal.
PCB Weakness:
- 0.5mm pitch footprint is small for handsoldering
- Amplifier package does not have edge lead tail, to make you certain about solder connectivity
But other than foot print and devices package chosen, tools are extremely important:
Tools weakness:
- Bulky 60W iron used and caused catastrophy there :(
- Use of thick solder wire
- Lower melting point solder plus hot air could help success of assmbling but was missed
Tools strength:
- Precise tweezer
- Good lenz for zooming
And the thing I had really missed was to be patience to waint until accessing at least SMD specialized iron.
Here is manufactured PCB:
Prepaird workbench:
First try success:
but the secound not:
I had placed tip of my bulky iron beneath the IC and the resin of PCB burnd!! Though I've been dissapointed. I told OK. I will make the secound PCB with success. The secound PCB had inherent wrong. It missed one track in sensitive area, Under amplifier. :(
But I managed to handle it with 0.1mm Wire, Low melting solder and Hot air
And the result was promising:
Though I've assembled all amplifier with success. Then I tried to place other components with my bulky iron and wire solder. Then another tack removed and caused to one amplifier being detached.
Now next time I will be sure to use smd iron. Then all components should have more than 1mm pitch for handsoldering. Otherwise I should have sharp tip iron with low melting point solder if possible. Plus patience.
Parts
85| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 22u | Capacitor_SMD:C_0805_2012Metric | C8, C17, C28, C30, C31, C33, C36, C37, C38, C39 |
| 8 | C_Feedthrough | Capacitor_SMD:FeedThrough_NFM3DPC | C10, C11, C12, C13, C14, C15, C16, C18 |
| 7 | 33n | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C9, C20, C21, C22, C23, C24, C25 |
| 7 | 470p | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C2, C3, C4, C5, C6, C7 |
| 7 | 6.8n | Inductor_SMD:L_0402_1005Metric_Pad0.77x0.64mm_HandSolder | L1, L2, L3, L4, L6, L7, L8 |
| 7 | MAX2659ELT+TG47 | Package_DFN_QFN:UDFN-6 1.5x1x.75mm | U1, U2, U3, U4, U5, U6, U7 |
| 4 | SF1186E-2 | Filter:Filter_SAW_Epcos_DCC6C_3x3mm | U9, U10, U11, U13 |
| 4 | TestPoint | Connector_Wire:SolderWirePad_1x01_SMD_5x10mm | TP1, TP2, TP3, TP4 |
| 3 | .9nH | Inductor_SMD:L_0402_1005Metric | L5, L9, L14 |
| 3 | 100n | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C26, C27, C29 |
| 3 | 2.7u | Inductor_SMD:4x4x2.8mmIND_VLCF4028T-2R7N1R8-2 | L10, L11, L12 |
| 3 | Conn_Coaxial_Small | Connector_Coaxial:SMA_Molex_73251-1153_EdgeMount_Horizontal | J2, J4, J5 |
| 1 | 18K | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 2.2 | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 22nH | Inductor_SMD:L_0603_1608Metric | L13 |
| 1 | 47K | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | AP7384-33Y | Package_TO_SOT_SMD:SOT-89-3 | U12 |
| 1 | BNX028 | Filter:Filter_Murata_BNX025 | FL1 |
| 1 | Input | Connector_Coaxial:SMA_Molex_73251-1153_EdgeMount_Horizontal | J1 |
| 1 | Jack-DC | Connector_BarrelJack:BarrelJack_Horizontal | J3 |
| 1 | TPS62933 | Package_TO_SOT_SMD:SOT-583-8 | U8 |
The 75 most common of 85 parts.
Similar boards
- 2 layers21.5 × 19 mm

- 6 layers100 × 45 mm

Esphome rgbcct led controller
mikelawrence/esphome-rgbcct-led-controller
ESPHome RGBCCT LED Controller is a PCB design that support a 5-Channel LED arrangement with Red, Green, Blue, Warm White and Cool White LEDs.
83 parts1CERN-OHL-P-2.0 - 2 layers23.1 × 34.3 mm

- 2 layers33 × 33 mm

- 2 layers58.7 × 110.9 mm

- 2 layers33 × 33 mm

- 2 layers89.2 × 103.5 mm

Oas
hubertciebiada/open-ambient-sensor
OAS — Open Ambient Sensor: DIY multi-sensor indoor environmental monitor (CO2, PM, VOC/NOx, temperature/humidity, mmWave presence) on ESP32-C6 with ESPHome / Home Assistant integration
64 parts44GPL-3.0 - 6 layers39.5 × 39.5 mm

P4eregrine
anticitizn/p4eregrine
All-in-one ESP32 P4-based drone ESC, flight controller, and video processor
359 parts21
Questions
How big is the Alm PCB?
It measures 82.5 × 87.9 mm and has 4 copper layers, 1.64 mm thick.
What parts does the Alm use?
85 parts, built around the TPS62933DRL, SF1186E-2, AP7384-33Y and BNX028-01. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Alm KiCad files?
From the mohammadsdtmnd/How-to-not-fail-RF-PCB-prototype repository on GitHub, at the commit this page was made from: the board is KICADprj/alm.kicad_pcb and its schematic KICADprj/alm.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Alm design in my own project?
Its repository states no licence, so its author keeps all rights: ask mohammadsdtmnd before reusing the design.