

Power supply 1.02
- Size
- 95 × 56 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 80
- Nets
- 57
- Pads
- 239
- Tracks, vias
- 548, 34
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 26 Sep 2021
- Updated
- 9 Jan 2022
Overview
Power supply 1.02 is an open-source printed circuit board by mike-crius, from the mike-crius/Crius-PowerSupply-PCB repository on GitHub. It is a 2-layer board of 95 × 56 mm with 80 parts on 57 nets, routed with 548 tracks and 34 vias.
It is built around the PIC16F1709-E/P, MCP9700A-E/TT and XL4015E1, with the ALD910027SAL, BTS443P and V8PAM10S among its other parts. Its parts include 25 resistors, 11 diodes, 10 connectors, 7 capacitors and 7 ICs. It belongs with the power boards and the PIC boards of this library.
Main components
8PIC16F1709-E/P
PDIP-20-40℃~+125℃ 10bit 14KB 18 1KB 2.3V~5.5V 32MHz 8 Bit 8bit Built-in FLASH PIC PDIP-20 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)MCP9700A-E/TT
SOT-23-40℃~+125℃ 2.3V~5.5V ±2℃ SOT-23 Temperature Sensors ROHSMicrochip TechnologyTemperature SensorsXL4015E1
TO-263-5-40℃~+125℃ 1 1.25V~32V 180kHz 5A 5mA 8V~36V Adjustable Buck Buck Built-in No TO-263-5 DC-DC Converters ROHSXLSEMIDC-DC ConvertersALD910027SAL
SOIC-80℃~+70℃ 10.6V 2 N-Channel 2.7V 23000MΩ@2.3V 30pF 500mW 80mA SOIC-8 MOSFETs ROHSAdvanced Linear DevicesMOSFETsBTS443P
TO-252-4-40℃~+150℃ 1 16mΩ 25A 5V~36V Active Low High Side Switch Overvoltage Protection、Under-voltage lockout、Reverse voltage protection、Integrated charge pump、Overcurrent Protection、Over temperature protection、Short-Circuit Protection TO-252-4 Power Distribution Switches ROHSInfineon TechnologiesPower Distribution SwitchesV8PAM10S
SOD-221BCSOD-221BC New Arrivals ROHSVishay IntertechnologyUncategorisedBAT54SW
SOT-3231 Pair Series Connection 200mA 2uA@25V 30V 600mA 800mV@100mA SOT-323 Schottky Diodes ROHSNexperiaSchottky DiodesSPD18P06PGBTMA1
TO-252-55℃~+175℃ 1 P-Channel 120pF 130mΩ@10V 18.6A 290pF 33nC@10V 4V 60V 80W 860pF P-Channel TO-252 MOSFETs ROHSInfineon TechnologiesMOSFETs
Parts
80| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 1k | Resistor_SMD:R_1206_3216Metric | R2, R3, R4, R5, R6, R11, R14, R21 |
| 6 | 10k | Resistor_SMD:R_1206_3216Metric | R1, R9, R12, R18, R23, R24 |
| 5 | 1k 0.1% | Resistor_SMD:R_1206_3216Metric | R7, R8, R16, R19, R20 |
| 5 | BSS806 | digikey-footprints:SOT-23-3 | Q1, Q2, Q4, Q5, Q7 |
| 3 | 9k 0.1% | Resistor_SMD:R_1206_3216Metric | R13, R15, R17 |
| 2 | 100F/200F | SuperCaps:SCC-22-30mm | SC1, SC2 |
| 2 | 100uF | Capacitor_SMD:CP_Elec_6.3x5.2 | C1, C7 |
| 2 | 1N914 | Diode_SMD:D_SOD-123F | D1, D2 |
| 2 | 1uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C5, C6 |
| 2 | 2.2uF Tant | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C3, C4 |
| 2 | V8PAM10S | Footprint_Library:DO-221BC | D5, D9 |
| 1 | .1 | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2 |
| 1 | 12V 5V | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | 12v, 0.5A nominal, 5A Surge | Connectors:Screw_Terminal_2Pin | J1 |
| 1 | 1R 25W | Connector_Wire:SolderWire-0.5sqmm_1x02_P4.6mm_D0.9mm_OD2.1mm | R10 |
| 1 | 470 | Resistor_SMD:R_1206_3216Metric | R25 |
| 1 | 50 | Resistor_SMD:R_1206_3216Metric | R22 |
| 1 | 5V 25W | Connectors:Screw_Terminal_2Pin | J8 |
| 1 | ALD910027 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | Activity | Diode_SMD:D_1206_3216Metric_Castellated | D8 |
| 1 | BAT54SW | Package_TO_SOT_SMD:SOT-323_SC-70 | D7 |
| 1 | BTS443P | Package_TO_SOT_SMD:TO-252-4 | U2 |
| 1 | D_Zener | Diode_SMD:D_SOD-123F | D11 |
| 1 | FAULT | Diode_SMD:D_1206_3216Metric_Castellated | D4 |
| 1 | FRAM I2C | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J9 |
| 1 | LOGO | Crius:Crius_logo_36x9mm | G*** |
| 1 | LOGO | Crius:Crius_logo_20x5mm | G*** |
| 1 | M1 Disconnect | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J10 |
| 1 | MAINPWR | Diode_SMD:D_1206_3216Metric_Castellated | D6 |
| 1 | MB85RC1MT | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | MCP111-SOT23 | digikey-footprints:SOT-23-3 | U5 |
| 1 | MCP1501-6Pin | digikey-footprints:SOT-23-6 | VRef1 |
| 1 | MCP1700-3302E_SOT23 | Package_TO_SOT_SMD:SOT-23 | U7 |
| 1 | MCP9700A | digikey-footprints:SOT-23-3 | U1 |
| 1 | PIC16F1709 | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U4 |
| 1 | PWRUP | Diode_SMD:D_1206_3216Metric_Castellated | D10 |
| 1 | Power Switch | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J2 |
| 1 | Program | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J5 |
| 1 | REMOVE to PRGM | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J7 |
| 1 | RESET | digikey-footprints:Switch_Tactile_SMD_6x6mm | S1 |
| 1 | SPD18P06PGBTMA1 | Package_TO_SOT_SMD:TO-252-3_TabPin2 | Q3 |
| 1 | SQ3495-EV | digikey-footprints:SOT-23-6 | Q6 |
| 1 | Serial Debug | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | ShutDown | Diode_SMD:D_1206_3216Metric_Castellated | D3 |
| 1 | Shutdown | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | U1V11F5 | Pololu:U1V11Fx | M2 |
| 1 | U3V70F5 | Pololu:U3V70F5 | M3 |
| 1 | XL4015 | Footprint_Library:XL4015 | M1 |
The 76 most common of 80 parts.
More from mike-crius/Crius-PowerSupply-PCB
1- 2 layers95 × 56 mm

Similar boards
- 2 layers100.3 × 100.3 mm

- 2 layers50 × 50 mm

- 4 layers94 × 90.2 mm

- 2 layers100 × 100 mm

- 8 layers100 × 60 mm

YAMMU ControlBoard v05
Zergie/YAMMU
A Multi Material Unit (MMU) for eight filaments that can also function as a filament dryer and can keep it dry while printing. The design is heavily inspired by voron and their printers.
234 parts107GPL-3.0 - 4 layers481.3 × 23.7 mm

Faraday rescue bms
nhallsny/faraday-rescue
Open source battery for e-bikes made by the now-defunct Faraday Bicycles
155 parts8CERN-OHL-P-2.0 - 4 layers129 × 79.5 mm

- 2 layers40.1 × 109.9 mm

Demiurge
AwesomeAudioApparatus/demiurge
Demiurge is a combination of Hardware and Software for Digital Sound Processing in the Eurorack Modular Synthesizer environment.
155 parts4Apache-2.0
Questions
How big is the Power supply 1.02 PCB?
It measures 95 × 56 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Power supply 1.02 use?
80 parts, built around the PIC16F1709-E/P, MCP9700A-E/TT, XL4015E1 and ALD910027SAL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Power supply 1.02 KiCad files?
From the mike-crius/Crius-PowerSupply-PCB repository on GitHub, at the commit this page was made from: the board is power_supply_1.02.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Power supply 1.02 design in my own project?
Its repository states no licence, so its author keeps all rights: ask mike-crius before reusing the design.