

Fpga extension
Repository for MSPC hardware design
- Size
- 47.5 × 50 mm
- Copper layers
- 6
- Thickness
- 1.05 mm
- Parts
- 120
- Nets
- 311
- Pads
- 790
- Tracks, vias
- 2,182, 315
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 10 Feb 2022
- Updated
- 13 Sep 2026
Overview
Fpga extension is an open-source printed circuit board by matgla, from the matgla/mspc repository on GitHub, published under the MIT licence. It is a 6-layer board of 47.5 × 50 mm with 120 parts on 311 nets, routed with 2,182 tracks and 315 vias.
It is built around the RP2040, W25Q128JVSIQ and TLV62569DRL, with the TLV75518PDBV, TLV75525PDBV and USBLC6-2P6 among its other parts. Its parts include 62 capacitors, 32 resistors, 9 ICs, 5 diodes and 4 connectors. It belongs with the fPGA and programmable logic boards and the RP2040 and FPGA and CPLD boards of this library.
Main components
10RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHTLV62569DRL
SOT-563-40℃~+125℃@(TJ) 1 1.5MHz 2.5V~5.5V 2A 35uA 600mV~5.5V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Operating status indication Step-down type Yes SOT-563 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTLV75518PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 1.8V 33uA 380mV@(500mA) 46dB@(100kHz) 5.5V 500mA 71.5uVrms Fixed Over Current Protection、Soft Start、Enable、Thermal Shutdown Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTLV75525PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 2.5V 238mV@(500mA) 25uA 46dB@(100kHz) 5.5V 500mA 71.5uVrms Fixed Over Current Protection、Thermal Shutdown、Enable control Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSBLC6-2P6
SOT-666-6-40℃~+125℃ 150nA 17V 2 3.5pF 5.25V 5A@8/20us 6V ESD IEC 61000-4-2 Unidirectional SOT-666-6 ESD and Surge Protection (TVS/ESD) ROHSSTMicroelectronicsESD And Surge Protection (TVS/ESD)W958D8NBYA
TFBGA-24TFBGA-24 New Arrivals ROHSWinbond ElecUncategorisedECS-120-8-36-CGN-TR
SMD2520-4P-40℃~+85℃ 12MHz 150Ω 8pF ±10ppm ±30ppm SMD2520-4P Crystals ROHSECSCrystalsSG-8002CE-PCB
SMD3225-4P-20℃~+70℃ 125MHz 28mA 3.3V CMOS ±50ppm SMD3225-4P Programmable Oscillators ROHSSeiko EpsonPre-Programmed OscillatorsTSM2301ACX RFG
SOT-23-55℃~+150℃ 1 P-Channel 10pF 1V 2.8A 20V 4.5nC@4.5V 460pF 480pF 700mW 90mΩ@4.5V P-Channel ±12V SOT-23 MOSFETs ROHSTaiwan SemiconductorMOSFETs
README
README.mdMSPC
Hardware for MSPC: a small modular computer built from a mainboard and extension cards that plug into the MSPC bus. The mainboard runs yasos.
Versions and branches
| branch | contents |
|---|---|
main | the current hardware: the v2 boards (same as mspc_v2) |
mspc_v1 | the first generation, kept for reference |
mspc_v2 | the v2 boards as built |
mspc_v2.5 | the next revision, work in progress; main moves there when it is done and that point is tagged mspcv2.5 |
Repository layout
Every board is a KiCad project with its fabrication outputs next to it in outputs/.
| directory | board |
|---|---|
mainboard/ | Mainboard (project in mainboard/mainboard/). RP2350B (80-QFN), QSPI flash and PSRAM, microSD, HS8836A USB hub, TLV320DAC3203 audio DAC, 12 V input with BD9D321EFJ bucks, three MSPC bus sockets (2×10 and 2×15, 1.27 mm). 4 copper layers. |
gpu_vga_extension/ | VGA card: RP2350A (60-QFN), 2× W25Q32JV flash, AP2112K 3.3 V regulator, resistor-ladder RGB DAC and DB15 connector. 24 × 50 mm, 4 layers. |
gpu_dvi_card/ | DVI card: same core as the VGA card, with an HDMI-type receptacle carrying DVI. 24 × 50 mm, 4 layers. |
fpga_extension/ | FPGA card (project in fpga_extension/fpga_extension/): Lattice ECP5 LFE5UM-85F, W958D8NBYA HyperRAM, QSPI configuration flash, microSD, and an on-board RP2040 USB-C JTAG programmer. 47.5 × 50 mm, 6 layers. |
bus_adapter_20pin/ | Passive breakout from the 2×10 1.27 mm bus socket to two 1×10 2.54 mm headers. |
bus_adapter_30pin/ | Passive breakout from the 2×15 1.27 mm bus socket to two 1×15 2.54 mm headers. |
simulation/ | 2022 SPICE sandbox: KiCad/ngspice schematics (audio filter, power switch) and PySpice scripts. Not a board. |
Working with the files
- The projects are in KiCad 8 format. Newer KiCad versions upgrade them on the first save, and the result no longer opens in KiCad 8. Do such an upgrade as its own commit, with no design changes, so later diffs stay readable.
- Schematic PDFs (
outputs/schematic.pdf) are tracked, so the schematics can be read without KiCad. Gerbers and drill files are not: plot them from the KiCad project when ordering a board. Per-machine files (backups, caches,*.kicad_prl, lock files, local history) are ignored too.
Known issues
- Some outputs are older than the boards they sit next to: the mainboard stencil (from v1), the GPU cards' schematic PDFs and stencils (from before the VGA/DVI split), and the FPGA card's schematic PDF. Regenerate them before the next order.
- The silkscreen of the 20-pin bus adapter reads "2x15" (copied from the 30-pin adapter).
- The libraries are copied into each project and have diverged.
Parts
120| Qty | Value | Footprint | References |
|---|---|---|---|
| 40 | 100n | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C2, C3, C17, C18, C19, C21, C26, C27, C29, C31, C32, C33, C34, C35, C36 +24 |
| 12 | 4.7u | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C6, C8, C9, C10, C11, C12, C13, C20, C22, C23, C24, C42 |
| 11 | 4.7k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R2, R3, R4, R5, R6, R8, R10, R12, R13, R14 |
| 4 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R18, R21, R26, R27 |
| 4 | 1u | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C30, C38, C60, C61 |
| 4 | 600 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R25, R29, R30, R31 |
| 4 | LED | LED_SMD:LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D2, D3, D4, D5 |
| 3 | DNF | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R7, R11, R15 |
| 3 | FerriteBead | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | FB1, FB2, FB3 |
| 2 | 10u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C14, C15 |
| 2 | 14p | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C25, C28 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R9, R24 |
| 2 | 27.4 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R22, R23 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R19, R20 |
| 2 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U2, U8 |
| 1 | 100k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R16 |
| 1 | 10u | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C39 |
| 1 | 120k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R17 |
| 1 | 2.2u | Inductor_SMD:L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | L1 |
| 1 | 22 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R32 |
| 1 | 6.8p | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C16 |
| 1 | <10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R28 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | Connector A 16-bit | Connector_PinHeader_1.27mm:PinHeader_2x15_P1.27mm_Vertical_SMD | J4 |
| 1 | D_Schottky | Diode_SMD:D_SOD-323_HandSoldering | D1 |
| 1 | ECS-120-8-36-CGN-TR | footprints:XTAL_ECS-120-8-36-CGN-TR | Y1 |
| 1 | Fuse | Fuse:Fuse_0603_1608Metric_Pad1.05x0.95mm_HandSolder | F1 |
| 1 | LFE5UM-85F-7BG381x | Package_BGA:Lattice_caBGA-381_17.0x17.0mm_Layout20x20_P0.8mm_Ball0.4mm_Pad0.4mm_NSMD | U1 |
| 1 | Micro_SD_Card_Det1 | Connector_Card:microSD_HC_Wuerth_693072010801 | J3 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U9 |
| 1 | SG-8002CE | Oscillator:Oscillator_SMD_SeikoEpson_SG210-4Pin_2.5x2.0mm | X1 |
| 1 | TLV62569DRL | Package_TO_SOT_SMD:SOT-563 | U6 |
| 1 | TLV75518PDBV | Package_TO_SOT_SMD:SOT-23-5 | U5 |
| 1 | TLV75525PDBV | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | TSM2301ACX | Package_TO_SOT_SMD:SOT-23W_Handsoldering | Q1 |
| 1 | USBLC6-2P6 | Package_TO_SOT_SMD:SOT-666 | U7 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | W958D8NBYA | footprints:BGA24C100P5X5_600X800X120 | U3 |
More from matgla/mspc
5- 4 layers100 × 100 mm

- 4 layers24 × 50 mm

- 4 layers24 × 50 mm

- 2 layers24 × 50 mm

- 2 layers47.5 × 50 mm

Similar boards
- 6 layers69.3 × 111.8 mm

FMC MIPI v2
VideoGPU/FMC_MIPI
FMC card to allow interfacing Xilinx FPGA boards with Jetson TX2 or TX1 via CSI-2 camera interface
143 parts22 - 4 layers109.8 × 145 mm

- 4 layers160 × 100.2 mm

Csa ultracpu
fachat/csa_ultracpu
The CPU board for a 17MHz Colour-PET clone with modern interfaces
175 parts9GPL-3.0 - 2 layers65 × 58 mm

- 2 layers21 × 18 mm

- 2 layers54.9 × 95 mm

Board v5
brev-dev/another_esp8266_sensor_board
PCB layout and instructions for a multi-purpose esp8266 sensor device, with optional LORA connectivity.
86 parts5GPL-3.0 - 2 layers145.5 × 174.5 mm

Hippanel
sneurlax/hip-badge
And join our matrix discussion channel: https://matrix.to/#/#hipbadge:matrix.org
630 parts1 - 4 layers52.3 × 80.3 mm

STM32F407ZXX Breakout
nedrysoft/STM32F407ZXX-Breakout
An STM32F4ZXX High Speed USB Breakout Design
84 parts
Questions
How big is the Fpga extension PCB?
It measures 47.5 × 50 mm and has 6 copper layers, 1.05 mm thick.
What parts does the Fpga extension use?
120 parts, built around the RP2040, W25Q128JVSIQ, TLV62569DRL and TLV75518PDBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Fpga extension KiCad files?
From the matgla/mspc repository on GitHub, at the commit this page was made from: the board is fpga_extension/fpga_extension/fpga_extension.kicad_pcb and its schematic bus_adapter_20pin/bus_adapter_20pin/bus_adapter_20pin.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Fpga extension design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).