2 layers100 × 50 mm
2 layers65 × 58 mm
Control panel
lucanastasio/myHomeAutomation1Home automation stuff
- Size
- 65 × 58 mm
- Copper layers
- 2
- Thickness
- 1.53 mm
- Parts
- 169
- Nets
- 139
- Pads
- 562
- Tracks, vias
- 1,156, 312
- Pours
- 17
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 16 May 2023
- Updated
- 18 Jan 2026
Overview
Control panel is an open-source printed circuit board by lucanastasio, from the lucanastasio/myHomeAutomation repository on GitHub. It is a 2-layer board of 65 × 58 mm with 169 parts on 139 nets, routed with 1,156 tracks and 312 vias.
It is built around the ATMEGA328PB-AU, TJA1051T/3/1 and AP64352SP, with the SPX3819M5-L-3-3, 74LVC1G57GM and P82B96D among its other parts. Its parts include 69 capacitors, 33 resistors, 12 connectors, 11 ICs and 9 inductors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
9
ATMEGA328PB-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 27 2KB 32KB 8 Bit AVR Built-in FLASH Power-on reset (POR)、Undervoltage detection (BOR/LVD/LVR/LVI)、Watchdog reset、External pin reset (NRST)、Built-in general-purpose timer、Programmable watchdog、Touch function TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)TJA1051T/3/1
-- CAN Transceivers ROHSNXP SemiconductorsCAN Transceivers
AP64352SP
SO-8-EP-40℃~+85℃ 1 100kHz~2.2MHz 22uA 3.5A 3.8V~40V 800mV~39V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Adjustable soft-start、Cycle-by-cycle current limiting、Frequency synchronization、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes SO-8-EP DC-DC Converters ROHSDiodes IncorporatedDC-DC Converters
SPX3819M5-L-3-3
SOT-23-5-40℃~+85℃@(Ta) 1 20V 3.3V 420mV@(100mA) 500mA 5uA 70dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
74LVC1G57GM
XSON-6(1x1.5)-40℃~+125℃ 1 1.65V~5.5V 2.3V、3.8V 3 32mA 32mA 4uA 5.1ns@5.5V,50pF 550mV、800mV 74LVC Series Configurable Multi-Function Gate XSON-6(1x1.5) Logic Gates ROHSNexperiaLogic Gates
P82B96D
SOIC-8-40℃~+85℃ 2 2-Wire Bus 2-Wire Bus 2V~15V 4pF 70ns Buffer SOIC-8 Signal Buffers, Repeaters, Splitters ROHSTexas InstrumentsSignal Buffers, Repeaters, Splitters
TXB0108DQSR
SON-20(2x4)-40℃~+85℃ 1.2V~3.6V 1.65V~5.5V 100Mbps Bidirectional Decoupling、Auto Direction Detection、Power-Off Protection Tri-State SON-20(2x4) Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level Shifters
2N7002DW
SOT-363-50℃~+150℃ 1.9Ω@10V 12pF 2 N-Channel 2.5V 300mA 300mW 60V 650pC@30V SOT-363 MOSFETs ROHSGuangdong HottechMOSFETs
SG-8002CE-PCB
SMD3225-4P-20℃~+70℃ 125MHz 28mA 3.3V CMOS ±50ppm SMD3225-4P Programmable Oscillators ROHSSeiko EpsonPre-Programmed Oscillators
README
README.mdmyHomeAutomation
Home automation stuff
Hardware
- Dimmer: LED APA102-2020, 4 PWM ch.
- Central: 4 PWM ch., radar UART, air valve 4 pin
Parts
169| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | C | Capacitor_SMD:C_0603_1608Metric | C8, C10, C11, C12, C15, C31, C32, C33, C34, C35, C36, C58, C59, C61, C62, C63 |
| 14 | 1u | Capacitor_SMD:C_0603_1608Metric | C13, C18, C20, C22, C23, C24, C27, C28, C39, C43, C45, C49, C51, C52 |
| 14 | R | Resistor_SMD:R_0603_1608Metric | R4, R5, R6, R7, R8, R9, R10, R11, R17, R20, R22, R23, R40, R41 |
| 13 | 100n | Capacitor_SMD:C_0603_1608Metric | C5, C40, C41, C54, C64, C65, C66, C67, C70, C71, C75, C76, C77 |
| 10 | 22u | Capacitor_SMD:C_0805_2012Metric | C1, C2, C6, C9, C16, C21, C25, C26, C46, C78 |
| 9 | R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R12, R13, R14, R15, R27, R28, R29, R30 |
| 4 | C | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C29, C30, C37, C38 |
| 4 | L | Inductor_SMD:L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | L4, L5, L6, L7 |
| 4 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP4, JP5, JP7, JP8 |
| 4 | SolderJumper_3_Open | Jumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1, JP2, JP3, JP6 |
| 3 | 200 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3, R39 |
| 3 | D | Package_TO_SOT_SMD:SOT-23_Handsoldering | D5, D6, D7 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R33, R34 |
| 2 | 100u_50V | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C3, C17 |
| 2 | 10u | Capacitor_SMD:C_1206_3216Metric | C7, C14 |
| 2 | 20p | Capacitor_SMD:C_0603_1608Metric | C68, C69 |
| 2 | 22n | Capacitor_SMD:C_0603_1608Metric | C19, C44 |
| 2 | 3mm_Mounting_Hole | project_footprints:NPTH_3mm_ID | H3, H4 |
| 2 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C50, C53 |
| 2 | Conn_01x03 | Connector_JST:JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J9, J10 |
| 2 | L | Inductor_SMD:L_1210_3225Metric | L3, L10 |
| 2 | R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R18, R19 |
| 2 | SPX3819M5-L-3-3 | Package_TO_SOT_SMD:SOT-23-5 | U7, U10 |
| 1 | 0 | Resistor_SMD:R_0603_1608Metric | R21 |
| 1 | 12k | Resistor_SMD:R_0603_1608Metric | R32 |
| 1 | 220u_16V | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C4 |
| 1 | 2N7002DW | Package_TO_SOT_SMD:SOT-363_SC-70-6 | Q1 |
| 1 | 40HAT | project_footprints:raspberry_pi | J3 |
| 1 | 470k | Resistor_SMD:R_0603_1608Metric | R31 |
| 1 | 47u_3A | project_footprints:L_Bourns-SRN6045 | L1 |
| 1 | 74LVC1G57 | Package_TO_SOT_SMD:SOT-363_SC-70-6 | U2 |
| 1 | AP64352 | project_footprints:Diodes_SO-8EP | U5 |
| 1 | ATmega328PB-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U6 |
| 1 | AVR-ISP-6 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J12 |
| 1 | BCT0102 | Package_TO_SOT_SMD:SOT-23-8 | U8 |
| 1 | C | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C60 |
| 1 | Conn_01x02 | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J7 |
| 1 | Conn_01x02 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J6 |
| 1 | Conn_01x04 | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J8 |
| 1 | Conn_02x02_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x02_P2.54mm_Vertical | J2 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y2 |
| 1 | DNP | Diode_SMD:D_SOD-523 | D3 |
| 1 | D_Zener | Diode_SMD:D_SMA | D1 |
| 1 | FerriteBead | Inductor_SMD:L_0603_1608Metric | FB1 |
| 1 | Fuse | Fuse:Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 1 | HP_L | project_footprints:TestPoint_Pad_D1.5mm | TP9 |
| 1 | HP_R | project_footprints:TestPoint_Pad_D1.5mm | TP7 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D4 |
| 1 | LIN3 | project_footprints:TestPoint_Pad_D1.5mm | TP10 |
| 1 | LM397 | Package_TO_SOT_SMD:SOT-23-5 | U12 |
| 1 | L_Ferrite | Inductor_THT:L_Radial_D7.5mm_P3.50mm_Fastron_07P | L2 |
| 1 | L_Ferrite_Coupled | Inductor_SMD:L_CommonModeChoke_Coilcraft_0805USB | L8 |
| 1 | NRF24L01_Breakout | project_footprints:nRF24L01_Breakout | U9 |
| 1 | OUT3 | project_footprints:TestPoint_Pad_D1.5mm | TP8 |
| 1 | P82B96 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | PB0 | project_footprints:TestPoint_Pad_D1.5mm | TP1 |
| 1 | PD4 | project_footprints:TestPoint_Pad_D1.5mm | TP2 |
| 1 | PD5 | project_footprints:TestPoint_Pad_D1.5mm | TP3 |
| 1 | PD6 | project_footprints:TestPoint_Pad_D1.5mm | TP4 |
| 1 | PD7 | project_footprints:TestPoint_Pad_D1.5mm | TP5 |
| 1 | PE1 | project_footprints:TestPoint_Pad_D1.5mm | TP6 |
| 1 | RIN3 | project_footprints:TestPoint_Pad_D1.5mm | TP11 |
| 1 | SG-8002CE | Oscillator:Oscillator_SMD_SeikoEpson_SG8002CE-4Pin_3.2x2.5mm | X1 |
| 1 | SM712_SOT23 | Package_TO_SOT_SMD:SOT-23_Handsoldering | D2 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_B3U-1000P | SW1 |
| 1 | Screw_Terminal_01x04 | Connector_Phoenix_MC:PhoenixContact_MC_1,5_4-G-3.5_1x04_P3.50mm_Horizontal | J5 |
| 1 | Screw_Terminal_CAN | Connector_Phoenix_MC:PhoenixContact_MC_1,5_4-G-3.81_1x04_P3.81mm_Horizontal | J4 |
| 1 | TJA1051T-3 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | TXB0108DQSR | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U3 |
| 1 | WM8960 | project_footprints:QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm_ThermalVias | DA1 |
| 1 | display | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J1 |
| 1 | motion and brightness sensors | Connector_JST:JST_PH_B5B-PH-K_1x05_P2.00mm_Vertical | J13 |
More from lucanastasio/myHomeAutomation
12- 4 layers50 × 50 mm
- 2 layers100 × 60 mm
- 2 layers50 × 50 mm
- 2 layers60 × 100 mm
- 4 layers50 × 36 mm
- 2 layers44 × 40.5 mm
- 2 layers55 × 35 mm
- 2 layers25 × 25 mm
- 2 layers40 × 40 mm
- 2 layers40 × 100 mm
- 2 layers22 × 40 mm
Similar boards
- 2 layers51 × 30.9 mm
- 4 layers160 × 100.2 mm
Csa ultracpu
fachat/csa_ultracpu
The CPU board for a 17MHz Colour-PET clone with modern interfaces
175 parts9GPL-3.0 - 2 layers21 × 18 mm
- 6 layers47.5 × 50 mm
- 2 layers391 × 131.1 mm
- 2 layers99.1 × 99.1 mm
Connector test stand
L0czek/rakieta
The starter board provides the ignition impulse to fire the engine. It includes an I2C IO expander and an 8-channel digital comparator to require a correct safety byte/address to be present before firing.
86 parts - 4 layers426 × 182.3 mm
- 2 layers50 × 100 mm
Questions
How big is the Control panel PCB?
It measures 65 × 58 mm and has 2 copper layers, 1.53 mm thick.
What parts does the Control panel use?
169 parts, built around the ATMEGA328PB-AU, TJA1051T/3/1, AP64352SP and SPX3819M5-L-3-3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Control panel KiCad files?
From the lucanastasio/myHomeAutomation repository on GitHub, at the commit this page was made from: the board is hardware/control_panel/control_panel.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Control panel design in my own project?
Its repository states no licence, so its author keeps all rights: ask lucanastasio before reusing the design.