
DoombiqMovedHoles
Architeuthis-Flux/Doombiq
An ultra low power, energy harvesting board that lets you "run" Doom

ALRT v2 is an open-source printed circuit board by martinbrzozowski, from the martinbrzozowski/ALRThw repository on GitHub. It is a 4-layer board of 30.5 × 30.5 mm with 37 parts on 44 nets, routed with 164 tracks and 18 vias.
It is built around the MPU-6050, LPR6235-752SMRC and MMBT3904, with the PTS810SJM250SMTRLFS among its other parts. Its parts include 14 resistors, 7 capacitors, 5 diodes, 4 connectors and 3 transistors. It belongs with the ESP32 and RISC-V boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 100R | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R4, R5 |
| 5 | 10k | Resistor_SMD:R_0603_1608Metric | R6, R7, R8, R12, R14 |
| 4 | LED | LED_SMD:LED_0603_1608Metric | D1, D2, D3, D4 |
| 2 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C3, C4 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R9, R10 |
| 2 | 2N7002 | 2N7002:SOT95P240X111-3N | Q1, Q2 |
| 1 | 0R | Resistor_SMD:R_0603_1608Metric | R13 |
| 1 | 100uF DNP | Capacitor_SMD:C_1206_3216Metric | C6 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 2.2nF | Capacitor_SMD:C_0603_1608Metric | C5 |
| 1 | 22uF | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | Battery | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | Beetle_ESP32-C3_v2 | ALRT_v1:Beetle_ESP32_C3 | U1 |
| 1 | DIODE | Diode_SMD:D_SOD-123 | D5 |
| 1 | DNP | Capacitor_SMD:C_0603_1608Metric | C7 |
| 1 | Electrodes | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | HR_PCB | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | LPR6235-752SMRC | KiCad:LPR6235_1 | L1 |
| 1 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q3 |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U2 |
| 1 | PTS810_SJM_250_SMTR_LFS | PTS810_SJM_250_SMTR_LFS:SW_PTS810_SJM_250_SMTR_LFS | SW1 |
| 1 | Vibrator | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |

Architeuthis-Flux/Doombiq
An ultra low power, energy harvesting board that lets you "run" Doom


hwreverse/MorphESP240_Shields
HWR0's Shield Designs for the MorphESP 240 by @ccadic

Sagaz0501/esp32-drone
PCB ESP32 quadcopter: KiCad hardware + Madgwick IMU firmware + WiFi web UI


SRiegle2020/ECE49022_SrDsgn_f22_Team44
ECE49022, Team44, f2022. Biometric "Smart" Watch

yogesh8441/ESP32-S3-PCB-Design
A custom 2-layer ESP32-S3 development board designed in KiCad 10 featuring an onboard USB-to-UART interface, automatic boot/reset circuit, USB Type-C connectivity, onboard MPU6050 IMU sensor, and 3.3V regulated power…

xjjak/LapCal
Building gloves that enable typing on a 34-key keyboard without an actual physical keyboard using IMUs and machine learning.
It measures 30.5 × 30.5 mm and has 4 copper layers, 4.69 mm thick.
37 parts, built around the MPU-6050, LPR6235-752SMRC, MMBT3904 and PTS810SJM250SMTRLFS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the martinbrzozowski/ALRThw repository on GitHub, at the commit this page was made from: the board is ALRT_v2/ALRT_v2.kicad_pcb and its schematic ALRT_v1/ALRT_v1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask martinbrzozowski before reusing the design.