2 layers70.1 × 63.5 mm
2 layers103.9 × 43.5 mm
Cps2 digiav
marqs85/cps2_digiav49CPS2 digital AV interface
- Size
- 103.9 × 43.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 146
- Nets
- 162
- Pads
- 745
- Tracks, vias
- 2,734, 331
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 31 Aug 2017
- Updated
- 21 Mar 2026
Overview
Cps2 digiav is an open-source printed circuit board by marqs85, from the marqs85/cps2_digiav repository on GitHub. It is a 2-layer board of 103.9 × 43.5 mm with 146 parts on 162 nets, routed with 2,734 tracks and 331 vias.
It is built around the 74LVC245AD, SN74LVC2G17DBV and IS25LP016D-JBLE, with the SRC4190IDB, TLV70012DCK and AP7361-33E among its other parts. Its parts include 77 capacitors, 20 resistors, 16 ICs, 8 connectors and 4 diodes. It belongs with the interfaces and adapters boards of this library.
Main components
12
74LVC245AD
SOIC-20-300mil-40℃~+125℃ 1 1.65V~3.6V 2.9ns@3.3V,50pF 24mA 40uA 74LVC 8 Bidirectional Schmitt trigger Tri-State SOIC-20-300mil Buffers, Drivers, Receivers, Transceivers ROHSNexperiaBuffer/Driver/Transceiver
SN74LVC2G17DBV
SOT-23-6-40℃~+85℃ 1 1.65V~5.5V 10uA 2 32mA 32mA 5.4ns@3.3V,50pF 74LVC Schmitt trigger SOT-23-6 Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, Transceivers
IS25LP016D-JBLE
SOIC-8-208mil100,000 cycles 133MHz 16Mbit 2.3V~3.6V 20 Years 200us 5uA Power-on reset、Hardware write protection、Software write protection、Write enable latch SPI SOIC-8-208mil NOR FLASH ROHSISSINOR FLASH
SRC4190IDB
SSOP-28-45℃~+85℃ 3.3V 4kHz~212kHz I2S Sample Rate Converter SSOP-28-208mil Audio Interface ICs ROHSTexas InstrumentsAudio Interface ICs
TLV70012DCK
SC-70-5-40℃~+125℃@(Tj) 1 1.2V 200mA 31uA 48uVrms 5.5V 68dB@(1kHz) Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Enable SC-70-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
AP7361-33E
SOT-223-40℃~+85℃@(Ta) 1 1A 3.3V 500mV@(1A) 65dB@(1kHz) 6V 70uA Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
SI5351C-B-GM
QFN-20(4x4)-40℃~+85℃ 1.71V~3.6V 200MHz 70ps 70ps 8 Built-in phase-locked loop、Spread spectrum、Built-in clock monitoring and loss-of-lock detection、Multi-source clock input CMOS External I2C Support QFN-20(4x4) Clock Generators, PLLs, Frequency Synthesizers ROHSSkyworks SolutionsClock Generators, PLLs, Frequency SynthesizersTLV70018DCK
SC-70-5-40℃~+125℃@(Tj) 1 1.8V 200mA 250mV@(200mA) 31uA 48uVrms 5.5V 68dB@(1kHz) Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Enable SC-70-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTLV70025DCK
SC-70-5-40℃~+125℃@(Tj) 1 2.5V 200mA 250mV@(200mA) 31uA 48uVrms 5.5V 68dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Thermal Shutdown Positive SC-70-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsRCLAMP0524P
DFN2510-10-55℃~+125℃ 0.35pF、0.8pF 17V 4.5A 5V 6.8V 80nA ESD Four channels IEC 61000-4-2 Unidirectional DFN2510-10 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)
MF-FSMF020X-2
0603-40℃~+85℃ 0.65mm 1.05mm 1.85mm 200mA 40A 500mA 500mW 600ms 900mΩ 9V 0603 Resettable Fuses ROHSBournsResettable FusesTL2243
插件-20℃~+70℃ 1.8N 12V 3.8mm 30,000 cycles 50mA 7.3mm 9.6mm PC Pin Right Angle Round Button SPST 插件 Tactile Switches ROHSE-SwitchTactile Switches
README
README.mdCPS2 digital AV interface (Rev 2)
Overview
cps2_digiav is an add-on for Capcom CP System II and some other arcade boards. It enables digital video and audio output via HDMI connector. The project consists of a common interface PCB (pcb/) and board-specific FPGA firmware (board/<board>/output_files/cps2_digiav.jic).
Supported boards
- CPS1 (89626A)
- CPS2
- CPS3
- Neo Geo (MV1C, AES3-3 and AES3-6, possibly others as well)
- Toaplan V2
Hardware
The add-on PCB design can be self-built or bought pre-assembled.
- Installation typically requires a small number of additional components which are listed in board-specific READMEs.
More info and discussion
Parts
146| Qty | Value | Footprint | References |
|---|---|---|---|
| 59 | 0.1u | custom_components:SM0603_Capa_libcms | C2, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23, C25, C39, C40, C41, C101 +43 |
| 9 | 10k | custom_components:SM0603_Resistor_libcms | R6, R7, R8, R16, R17, R18, R21, R22, R41 |
| 9 | 10u | custom_components:SM0603_Capa_libcms | C1, C3, C10, C11, C12, C13, C26, C49, C108 |
| 8 | 1u | custom_components:SM0603_Capa_libcms | C87, C89, C91, C92, C94, C96, C97, C98 |
| 5 | 2.2k | custom_components:SM0603_Resistor_libcms | R1, R2, R5, R45, R46 |
| 5 | GND | custom_components:SMD_PAD | W7, W8, W9, W10, W14 |
| 4 | GS2 | Connectors:GS2 | J3, J5, J6, J7 |
| 4 | MPZ1608S221A | custom_components:SM0603_Resistor_libcms | FB1, FB2, FB3, FB4 |
| 3 | 4.7k | custom_components:SM0603_Resistor_libcms | R4, R19, R24 |
| 3 | 74LVC245 | custom_components:TSSOP-20_4.4x6.5mm_Pitch0.65mm_Handsoldering | U3, U4, U5 |
| 3 | SN74LVC2G17 | custom_components:SOT-23-6_Handsoldering | U8, U9, U16 |
| 2 | Conn_02x05 | custom_components:HLE-105-02-G-DV-PE | J1, J2 |
| 2 | RClamp0524P | custom_components:SLP2510P8 | D2, D3 |
| 2 | TLV70012 | custom_components:SOT-23-5_Handsoldering | U12, U14 |
| 1 | 10CL025YE144C8N | custom_components:TQFP-144_thermal | U2 |
| 1 | 1k | custom_components:SM0603_Resistor_libcms | R20 |
| 1 | 25 | custom_components:SM0603_Resistor_libcms | R23 |
| 1 | 47u | custom_components:SM0603_Capa_libcms | C5 |
| 1 | 5V | custom_components:SMD_PAD | W1 |
| 1 | 887 | custom_components:SM0603_Resistor_libcms | R3 |
| 1 | ADV7513 | custom_components:LQFP-64-1EP_10x10mm_Pitch0.5mm_Handsoldering | U1 |
| 1 | AP7361 | custom_components:SOT-223_Handsoldering | U7 |
| 1 | BCK | custom_components:SMD_PAD | W2 |
| 1 | C1 | custom_components:SMD_PAD | W15 |
| 1 | C2 | custom_components:SMD_PAD | W13 |
| 1 | DAT | custom_components:SMD_PAD | W4 |
| 1 | HDMI_CONN | custom_components:HDMI_CONN-10029449-111RLF | J4 |
| 1 | HS | custom_components:SMD_PAD | W11 |
| 1 | IS25LP016D-JBLE | custom_components:SOIC-8_3.9x4.9mm_Pitch1.27mm_Handsoldering | U10 |
| 1 | JTAG_CONN | Connect:VASCH5x2 | P1 |
| 1 | MF-FSMF020X-2 | custom_components:SM0603_Resistor_libcms | F2 |
| 1 | SD05-7 | custom_components:SOD-323_Handsoldering | D1 |
| 1 | SI5351C-B | custom_components:QFN-20-1EP_4x4mm_Pitch0.5mm_Handsoldering | U6 |
| 1 | SRC4190 | Housings_SSOP:SSOP-28_5.3x10.2mm_Pitch0.65mm | U11 |
| 1 | TL2243 | custom_components:TL2243 | SW1 |
| 1 | TLV70018 | custom_components:SOT-23-5_Handsoldering | U15 |
| 1 | TLV70025 | custom_components:SOT-23-5_Handsoldering | U13 |
| 1 | VS | custom_components:SMD_PAD | W12 |
| 1 | WS | custom_components:SMD_PAD | W3 |
| 1 | ZHCS400TA | custom_components:SOD-323_Handsoldering | D4 |
| 1 | vol+ | custom_components:SMD_PAD | W5 |
| 1 | vol- | custom_components:SMD_PAD | W6 |
More from marqs85/cps2_digiav
2- 2 layers33.4 × 10.9 mm
Similar boards
- 2 layers118.2 × 73 mm
- 4 layers124.6 × 68.7 mm
- 4 layers100 × 100 mm
- 4 layers100 × 100 mm
- 4 layers100 × 100 mm
- 4 layers42 × 44.4 mm
STM32 FlightController
JLjoestar23/STM32_FlightController
PCB, software, firmware, and other files related to a custom made STM32-based flight controller.
56 parts1 - 4 layers
- 4 layers100 × 68 mm
Basic ecp5-pcb
mattvenn/basic-ecp5-pcb
Reference design for Lattice ECP5 FPGA. Featuring Raspberry Pi interface and 6 PMODs
75 parts144CC0-1.0
Questions
How big is the Cps2 digiav PCB?
It measures 103.9 × 43.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Cps2 digiav use?
146 parts, built around the 74LVC245AD, SN74LVC2G17DBV, IS25LP016D-JBLE and SRC4190IDB. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Cps2 digiav KiCad files?
From the marqs85/cps2_digiav repository on GitHub, at the commit this page was made from: the board is pcb/cps2_digiav.kicad_pcb and its schematic pcb_cps1_adapter/cps1_adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Cps2 digiav design in my own project?
Its repository states no licence, so its author keeps all rights: ask marqs85 before reusing the design.