Skip to the content
4 layers74.5 × 70.3 mmNest mini v2-drop in pcb, the printed circuit board in 3D

Nest mini v2-drop in pcb

marceldale/nest-mini-v2-voice4

Open voice satellite board for the Google Nest Mini (2nd gen): local Home Assistant voice assistant with ESP32-S3 + XMOS XU316, ESPHome, Voice PE compatible. Open hardware, prototype stage.

Size
74.5 × 70.3 mm
Copper layers
4
Thickness
1.6 mm
Parts
249
Nets
197
Pads
862
Tracks, vias
2,725, 470
Pours
1,025
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
1 Oct 2026
Updated
17 Oct 2026

Overview

Nest mini v2-drop in pcb is an open-source printed circuit board by marceldale, from the marceldale/nest-mini-v2-voice repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 4-layer board of 74.5 × 70.3 mm with 249 parts on 197 nets, routed with 2,725 tracks and 470 vias.

It is built around the 74AHCT1G125SE, ESP32-S3R8 and TPS62130RGT, with the CC0603KRX7R9BB104, SK6812-EC20 and 0402CG120J500NT among its other parts. Its parts include 106 capacitors, 70 resistors, 8 diodes, 8 inductors and 5 ICs. It belongs with the home automation and IoT boards and the ESP32 boards of this library.

Main components

12

README

README.md

Open voice satellite board for the Google Nest Mini (2nd gen)

A drop-in replacement board that turns a Google Nest Mini (2nd gen) into a fully local voice assistant for Home Assistant. Started from the open design by iMike78 (nest-mini-drop-in-pcb, CERN-OHL-S v2) and since then reworked, verified and extended into its own board. Everything that was changed, and why, is in CHANGES.md; the people and projects this one stands on are named under Credits.

[!WARNING] Status (17 Oct 2026): rev A2 brought up (board A, 14–16 Oct 2026). Do not manufacture rev A2 — rev A3 is in progress.

Verified on hardware: all power rails; USB and 14 V supply paths; firmware installation and Wi-Fi set-up via Improv; XMOS flash written by the ESP32 and XMOS firmware 1.3.1 running; amplifier on 14 V from the base plate; speech output; mute switch; wake word with the speech round trip to Home Assistant; echo cancellation with music playing (open set-up); all three touch areas.

Limited: Wi-Fi transmits cleanly only up to about 9 dBm (the firmware uses 8.5 dBm), so range is limited. The Nest Mini's metal mounting plate does not sit flat on the board — never fit it on a powered board.

Not tested yet: LED ring colours, Bluetooth set-up, long run, full volume, the closed housing.

Results, causes and what rev A3 changes: docs/BRINGUP.md. Setting up a board: docs/GETTING_STARTED.md.

Status Licence

What it is

The Google Nest Mini (2nd gen) is a well-built little speaker: a good 40 mm driver, a clean enclosure, two microphones and a touch surface. What ties it to Google is only the circuit board inside.

This project replaces that board. You open the Nest Mini, take out Google's electronics and put this board in its place. Speaker, housing, base plate and touch surface stay as they are. What you get is a fully local voice assistant for Home Assistant: wake word, speech and echo cancellation run on the device (ESP32-S3 + XMOS XU316), nothing leaves your network, and the speaker still plays music and announcements.

Under the hood it follows the Home Assistant Voice Preview Edition: same processor pair, same audio architecture, same ESPHome firmware base — fitted into the Nest Mini's size, power and mounting constraints.

What you need: a Nest Mini (2nd gen), this board (assembled), a Home Assistant installation and a USB-C cable for the ESP32. The XMOS gets its first image from the ESP32 itself (a two-step button in Home Assistant; verified on hardware on 15 Oct 2026 — see Highlights), or over JTAG (J4, an XTAG4 adapter). Wi-Fi is set up with Improv — over USB from web.esphome.io, or over Bluetooth confirmed by touching the centre button, as on Voice PE; there is no fallback access point. Add the device in Home Assistant right after the Wi-Fi set-up, so that Home Assistant sets the API encryption key (until then any client on the network could). If you run it from USB rather than from the Nest Mini's own 14 V base plate, use a supply that can give 1 A — at full LED brightness the board draws up to 0.8 A, so a plain 500 mA charger is not enough. On USB alone the amplifier has no supply — PVDD comes only from the 14 V rail (R66) — so the speaker stays silent while microphones, LEDs and Wi-Fi work; the log then shows a PVDD under-voltage fault or a tas58xx set-up error. That is expected, not a defect.

What it is not: a finished consumer product. It is an open hardware design at prototype stage (see status above). No affiliation with Google.

Highlights

  • XMOS flash written from the ESP32. A bus switch (U16, after the Satellite1 principle) lets the ESP32 write the XMOS flash directly; the ESPHome component xmos_flasher does it from a two-step button in Home Assistant. Verified on hardware (board A, 15 Oct 2026): JEDEC ID EF 40 16, 286 720 bytes written, MD5 match, about 21 s; after the restart voice_kit reads XMOS firmware 1.3.1. JTAG stays as the fallback: J4 is an xSYS2 pad field, an XTAG4 plugs on 1:1. Later updates run over I²C (DFU) from the ESP32.

    What the button overwrites: the whole 1 MiB boot partition of the XMOS flash U11 is erased (256 sectors) and rewritten with the factory image firmware/xmos/ffva_v1.3.1_factory.bin (286 720 bytes), checked against its MD5 and read back; everything after the image must read FFh. An image that a later DFU update put there is replaced by 1.3.1 as well. The data partition above 1 MiB is not touched, and the flash status registers are only read, never written — a write-protected flash is reported, not unlocked. It works on USB alone or on 14 V (all LEDs are switched off meanwhile; load below 0.5 A), needs the enable switch first and takes about 15 s; on success the ESP32 restarts.

  • Audio path as on Voice PE. ESP32 feeds the amplifier and the echo reference on one line; XU316 is the clock master. Works with the unmodified Voice PE XMOS firmware.

  • Power without operating rules. Upstream, USB-C and the 14 V supply must never be connected at the same time, and even USB alone back-feeds the 14 V rail through the buck converter (a known issue). This board adds an ideal diode (LM66100) behind the 5 V converter and a small switch that disables the USB supply while 14 V is present. Result: plug in USB, 14 V or both, in any order, without risk to the board or the host PC.

  • XU316 core on a buck converter. Upstream feeds the 0.9 V core from a 200 mA linear regulator dropping 2.4 V, while the XU316 draws about 300 mA typical and up to 1 A under DSP load: the regulator would overheat and the XMOS would brown out. This board uses the TPS62065 with 2 A. Also: touch controller wired, antenna matching at the antenna, mic-3 path removed, EasyEDA-checked footprints, every part with an LCSC number.

  • Expansion connector (12-pin FPC) for an add-on ring board. We wanted more than a voice satellite: presence detection (radar over UART), temperature/humidity (I²C), IR transmit and receive for controlling TV or air conditioning, and an LED ring. None of this fits inside the Nest Mini housing (the mounting plate sits flush on the board), so the connector stays unpopulated there and the board works as a plain Nest Mini replacement. In a custom enclosure it connects to a ring board — LEDs, IR emitters and receivers, radar module — that is planned as the next project. The main board carries the signals, the ring board carries the sensors.

Roadmap

  • Design review against upstream, Voice PE and Gen1 (CHANGES.md)
  • Rev A2 schematic and layout: XMOS flash via ESP32, Voice PE audio path, power without operating rules, expansion connector routed
  • Rev A2 silkscreen: pin-1 marks, test point labels, revision and date; no DRC warnings left
  • Independent audit of rev A2; critical and layout-relevant findings fixed (CHANGES.md section 10)
  • Rev A2 manufacturing files regenerated after the audit fixes (fertigung/, 1 Oct 2026)
  • Rotation check of the 31 changed or new parts in the fabricator's assembly preview (JLCPCB preview, 2 Oct 2026; U18, U16, U5, Q4 corrected in the CPL beforehand, Y1 by order remark)
  • ESP32-side flasher for the XMOS image (firmware/esphome/components/xmos_flasher/; fallback: J4 with an XTAG4) — verified on hardware, board A, 15 Oct 2026
  • Rev A2 ordered: 2 assembled boards (5 bare PCBs), JLCPCB, 2 Oct 2026
  • Bring-up, board A: resistance check, power rails, mute switch, Wi-Fi set-up via Improv, XMOS flash via ESP32 and bus switch U16 (14–15 Oct 2026); board B in progress
  • Wi-Fi transmit power: rev A2 transmits cleanly only up to about 9 dBm (crystal close to the RF path, supply of the RF stage; docs/BRINGUP.md); fixed in rev A3
  • Rev A3: RF section to Espressif's guidelines and Voice PE, mounting-plate fit — in progress
  • Audio output on 14 V, microphones and wake word, echo cancellation with music (open set-up), touch areas — board A, 15–16 Oct 2026 (docs/BRINGUP.md)
  • LED ring, Bluetooth set-up, long run, full volume, closed housing
  • Wi-Fi sensitivity against a reference device
  • Firmware release (ESPHome YAML + XMOS factory image)
  • Ring board and enclosure files
  • Certification plan
  • Crowd Supply campaign

Trademarks

Google and Google Nest Mini are trademarks of Google LLC. This project is not affiliated with, endorsed by or sponsored by Google. Home Assistant and ESPHome are projects of the Open Home Foundation / Nabu Casa. XMOS and xcore are trademarks of XMOS Ltd. All trademarks belong to their respective owners and are used here only to say what this board is compatible with.

Licences

WhatLicence
Hardware — schematic, layout, our footprints, manufacturing dataCERN-OHL-S v2
ESPHome YAML, Python tools, documentationMIT
XMOS firmware image under firmware/xmos/XMOS Public Licence v1 — not ours
ESPHome component xmos_flasher under firmware/esphome/components/GPL-3.0-only for the C++ files — derived from FutureProofHomes/Satellite1-ESPHome (memory_flasher, © Mischa Siekmann, commit 8f8906c), whose LICENSE is the ESPHome licence: C/C++ under GPLv3 without "or any later version", Python under MIT. __init__.py, the README and the host test are MIT. See LICENSES/GPL-3.0-only.txt
ESPHome component tas58xx under firmware/esphome/components/GPL-3.0-or-later — © mrtoy-me, based on work by Andriy Malyshenko (sonocotta); patched by us (start-up order, loop bandwidth), see firmware/esphome/PATCH.md
KiCad library excerpts in lib_lokal/CC-BY-SA-4.0, © KiCad Libraries Contributors
Parts of lib_lokal/ (vendor footprints and symbols)terms not established — see below

Full texts are in LICENSES/. Files that can carry a comment header do carry an SPDX-License-Identifier; for KiCad documents, Gerbers and binaries the assignment is in REUSE.toml, following the REUSE specification.

One honest gap, written up in LICENSES/LicenseRef-Vendor-Model-Terms-Not-Established.txt:

  • The vendor 3D models the board references are not part of this repository: we hold no licence document for any of them. The 3D view therefore shows those parts without a body; fabrication and assembly do not need them.
  • Parts of lib_lokal/ have a similar problem: ten of the 23 footprints in Onju.pretty carry a SnapEDA or EasyEDA note, New_Library.kicad_sym is SnapEDA, and the Seeed and reSpeaker symbols come from Seeed's project. They arrived with the upstream design and we pass them on unchanged. This directory cannot be left out — without it the design does not open.

lib_lokal/ and the two library tables are versioned on purpose. The design references every symbol and footprint through ${KIPRJMOD}/lib_lokal/, so a clone without them opens with empty placeholders. The directory holds trimmed excerpts, not whole libraries: Device.kicad_sym is 17 kB here against 2 374 kB in a KiCad 9.0.9 installation. KiCad's library licence grants an exception for designs that use the libraries but states that it does not apply when they are redistributed as a collection — which is what this directory does — so those files keep CC-BY-SA-4.0 with attribution.

The C++ code in this repository is the patched copy of the ESPHome component tas58xx (GPL-3.0-or-later) and the component xmos_flasher (GPL-3.0-only, because its source states GPLv3 without "or later"), both under firmware/esphome/components/; see the table above. CERN-OHL-S v2 is a strongly reciprocal licence: if you make and distribute a board from these files, or from a modified version of them, you have to make the complete source of your version available under the same licence. See LICENSES/CERN-OHL-S-2.0.txt, sections 3.2 and 4.


For reference

Everything below is the technical detail — useful once you have a board in your hand, and not needed to understand what the project is.

Test points

Eighteen pads, all bare copper, nothing to populate. Sixteen are on the microphone side; the touch electrodes are on the LED side. The silkscreen carries a short name next to each pad — the full net name would not fit on a 68 mm board.

MarkingRefNetSidePositionWhat you should see
3V3TP1+3V3microphone side163.00 / 74.503.3 V
5V_SWTP3/Power/+5V_SWmicrophone side121.40 / 102.00about 5 V, before the ideal diode U18
1V8TP4+1V8microphone side145.70 / 71.501.8 V
VDDTP5VDDmicrophone side130.40 / 81.600.9 V
3V3TP6+3V3microphone side107.40 / 94.603.3 V
XRSTTP11XU316_RSTLED side126.10 / 66.50logic; high = XU316 held in reset
MUTETP12MUTEmicrophone side140.90 / 116.80logic; follows the mute slider
PA_ENTP13AUDIO_PA_ENmicrophone side130.70 / 109.10logic; high = amplifier enabled
(no marking)TP14ELEC2LED side159.20 / 89.90touch electrode, right
(no marking)TP15ELEC1LED side135.82 / 119.53touch electrode, centre
(no marking)TP16ELEC0LED side114.20 / 88.90touch electrode, left
5VTP17+5Vmicrophone side122.42 / 105.55about 5 V, after U18 — below TP3 by I × 79 mΩ (LM66100 R_ON): ≈ 8 mV per 100 mA, 55…65 mV at 0.7…0.8 A
14VTP18+14Vmicrophone side143.90 / 109.4314 V from the base plate
RSTTP19ESP_RSTmicrophone side118.58 / 79.30logic; low = ESP32 in reset
BOOTTP20ESP_BOOTmicrophone side121.84 / 81.75logic; low at power-up = boot mode
GNDTP21GNDmicrophone side120.58 / 64.740 V reference, next to U8
GNDTP22GNDmicrophone side128.74 / 104.080 V reference, next to U14
VMICTP23VDD_MICmicrophone side105.10 / 88.353.3 V microphone supply

The three touch points carry no silkscreen: they sit inside the electrode rings on the LED side, where any lettering would end up on copper. Their names are T_R, T_C and T_L in the schematic.

The pair TP3 / TP17 is the one to measure first. TP3 sits before the ideal diode U18, TP17 after it. The difference is the load current times U18's on-resistance (79 mΩ typical, LM66100 datasheet): under 20 mV at idle, about 55…65 mV at 0.7…0.8 A; in USB-only operation TP3 should read roughly 0 V, because the 14 V rail is then dead and the diode blocks the path back into it.

Connectors

The board carries a designator and a pin-1 dot for every connector; the pinouts are here rather than on the silkscreen, where they would not be legible at 0.5 mm pitch.

J6 — ribbon cable to the LED ring board, 12 way, 0.5 mm pitch

PinNetPinNet
1GND7UART_RX
2+5V8I2C_SDA
3+5V9I2C_SCL
4GND10IR_TX
5LED_DOUT11IR_RX
6UART_TX12+3V3

Pin 1 is the one nearest the dot. LED_DOUT continues the LED chain from LED6 through R80, so the ring board's first LED is index 6 as far as the firmware is concerned.

POWER_IN1 — flat flex to the base plate, 10 way, 0.5 mm pitch

PinNetPinNet
1GND6GND
2MUTE7+14V
3GND8+14V
4GND9+14V
5GND10+14V

Confirmed pin for pin against an independent design: the schematic of Onju Voice (hardware/Onju-Home.SchDoc, a replacement board for the same Nest Mini 2nd gen) has the same ten-way connector as J1, and all ten pins agree — 1 and 3–6 GND, 2 MUTE, 7–10 14V. Metering it on an original is optional; the quick check is in CHANGES.md ("POWER_IN1: the pinout is now confirmed against a second source").

J4 — XMOS JTAG pad field, 2×5, 1.27 mm pitch, unpopulated

The pin-out is the xSYS2 JTAG-only header of the XU316 datasheet (appendix G.3, figure 25), so an XTAG4 plugs on 1:1 — pin 1 to pin 1. Pin 1 is marked by the silkscreen dot.

PinNetPinNet
1+1V8 (VREF)2TMS
3GND4TCK
5GND6TDO
7GND8TDI
9GND10RST_N

VREF is 1.8 V on pin 1, with 100 nF (C103) right next to it. There is no 5 V and no 3.3 V on this field. Up to the audit fixes of 1 Oct 2026 the field carried a rotated, non-standard pin-out with VREF on pin 6; a board made from an older revision needs an adapter.

Before bring-up

[!NOTE] Amplifier driver. The ESPHome core component tas58xx (TAS5805M) arrives with ESPHome 2026.10. Until then use ESPHome dev, or the patched copy under firmware/esphome/components/tas58xx, which nest-mini-v2-voice.yaml loads by default and which builds with ESPHome 2026.9.0. A configuration for the core component is nest-mini-v2-voice-kerntreiber.yaml (ESPHome dev / 2026.10 or later; it adds the 175 kHz loop bandwidth the core component does not set yet).

[!CAUTION] Do not burn EFUSE_STRAP_JTAG_SEL on the ESP32-S3. Rev A2 uses GPIO3 and GPIO39 to GPIO42 as an SPI bus to the XMOS flash. In the factory state JTAG runs over the USB-Serial/JTAG controller and those pins are free; burning the eFuse switches JTAG to those pins and breaks the XMOS flash path. Details in CHANGES.md.

Manufacturing files

fertigung/ holds the rev A2 set, generated after the audit fixes on 1 Oct 2026: Gerbers and Excellon drill files, gerber_jlcpcb.zip for upload, BOM and CPL for JLCPCB, BOM and assembly drawing for PCBWay. fertigung/ABLAUF.md documents the commands that produce it and the checks each one prints — nothing in that directory is edited by hand. It is not released: the board has never been fabricated, and two checks are still open (see below).

Before ordering, these are the points to watch; the full list with the evidence is under "Before you order" in CHANGES.md:

  • 0.10 mm minimum track width for the two UART signals — fabricable at JLCPCB without a surcharge, but not everywhere.
  • Via-in-pad: board vias reach into 23 pads (58 vias, all same-net), among them three signal pads and the large pads of U8 and U10. Order the vias Epoxy Filled & Capped.
  • U11 must be the IQ variant of the W25Q32JV, not IM — the footprint cannot tell them apart, and only IQ has the QE bit set at the factory.
  • Seven same-net via pairs sit exactly at the 0.2 mm hole-to-hole limit.
  • J1 (Molex 1054500101, C134092) is stocked but flagged “process difficult” in the BOM check — confirm it by hand.
  • Stack-up: 4 layers, 1.6 mm, JLC04161H-7628; surface finish chosen at order time.

Placement corrections by hand are no longer needed: rev A1 shipped a CPL with 19 of them, and rev A2 fixes the footprint origins themselves instead (X1, J5, J1), so the CPL exporter writes a correct CPL directly; the remaining nineteen corrections are applied automatically.

Two things are still open, both for the operator and both listed in fertigung/DREHLAGEN_PRUEFEN.md:

  1. 31 parts need checking in JLCPCB's assembly preview — those whose LCSC number changed since rev A1 (U5, LED2–LED5, J6, R76, R77, R80, X1, J1) or that are new (U16, U18, U19, Q4), nine from the audit fixes (L1, L2 with a new footprint; C20, C100 with new numbers; C105–C109 new, all unpolarised), and seven from the pin audit and the order (Y1 with a new number — the one where rotation matters, a 90° error puts the crystal on the ground pads, and it has no model in the preview, so the order carries the remark "Y1 orientation per silkscreen pin-1 corner mark (top-left)"; R72, C17, C63, C98, R35 with new numbers; R81 new). The first preview on 2 Oct 2026 found U18 and U16 turned; a recomputation of all 42 polarised parts against the fabricator's footprints corrected four rotations (U18, U16, U5, Q4) — see CHANGES.md. C110 is not fitted and not in the CPL. For them the fabricator's own footprint decides the zero orientation, and that has not been compared yet. Everything else was checked in rev A1 and has not moved since.
  2. Two order options are fixed for this board and have to be selected because they are not in the Gerbers: via covering Epoxy Filled & Capped (vias reach into 23 pads) and surface finish ENIG — decided, not optional (0.40 mm pitch, QFN thermal pads, the J4 spring-contact field, test points and touch electrodes). Both are in "Before you order" in CHANGES.md.

The upstream design and its own documents are at iMike78/nest-mini-drop-in-pcb.

Credits

This board exists because other people published theirs first.

  • iMike78 — nest-mini-drop-in-pcb, the design this one forks. The board outline, the mounting geometry, the microphone and touch arrangement and a great deal of the layout are the designer's work.
  • Onju Voice (Justin Alvey) — the first drop-in board for the Nest Mini, and the origin of the Onju footprint library this project still uses.
  • Home Assistant Voice PE (Nabu Casa / Open Home Foundation) — the audio architecture this board follows: the same ESP32-S3 + XMOS XU316 pair, the same clocking, and the XMOS firmware it runs.
  • Satellite1 (FutureProofHomes) — the method for flashing the XMOS from the ESP32, which is what makes this board programmable without a debugger.
  • ESPHome and Home Assistant — the firmware and the platform all of it runs on.

How to follow or contribute

Star or watch the repository. Issues and Discussions are handled here, in this repository: Discussions for questions, Issues for errors in the design or the documentation. Hardware support starts after bring-up. Reference thread: Home Assistant community, topic 860001.

Parts

249
QtyValueFootprintReferences
48100nFCapacitor_SMD:C_0402_1005MetricC30, C32, C33, C34, C37, C38, C41, C42, C43, C101, C103, C104, C105, C106, C108, C109 +32
150RResistor_SMD:R_0402_1005MetricR7, R14, R22, R24, R27, R28, R29, R30, R31, R40, R42, R43, R44, R45, R46
9100RResistor_SMD:R_0402_1005MetricR39, R47, R55, R56, R59, R60, R62, R63, R80
91uFCapacitor_SMD:C_0402_1005MetricC24, C31, C35, C39, C44, C53, C63, C68, C78
822uFCapacitor_SMD:C_0805_2012MetricC3, C10, C14, C22, C79, C81, C84, C85
7100kResistor_SMD:R_0402_1005MetricR8, R9, R10, R15, R16, R41, R75
610kResistor_SMD:R_0402_1005MetricR20, R21, R49, R58, R79, R81
5100nFCapacitor_SMD:C_0603_1608MetricC7, C8, C25, C82, C91
40.22uFCapacitor_SMD:C_0603_1608MetricC74, C75, C76, C77
410uFCapacitor_SMD:C_0603_1608MetricC13, C17, C18, C107
44.7kResistor_SMD:R_0402_1005MetricR32, R33, R50, R70
447kResistor_SMD:R_0402_1005MetricR36, R52, R65, R71
4SK6812-EC20Onju:SK6805-EC20LED2, LED3, LED4, LED5
3100nFCapacitor_SMD:C_0805_2012MetricC11, C19, C23
312pFCapacitor_SMD:C_0402_1005MetricC26, C27, C29
31MResistor_SMD:R_0402_1005MetricR34, R73, R76
34.7uFCapacitor_SMD:C_0603_1608MetricC6, C80, C90
20.68uFCapacitor_SMD:C_0805_2012MetricC86, C87
20RResistor_SMD:R_0805_2012MetricR68, R69
210nFCapacitor_SMD:C_0402_1005MetricC5, C16
210uFCapacitor_SMD:C_0805_2012MetricC4, C15
210uHOnju:MTQH404030S100MBTL6, L7
2120ROnju:BLM18PG121SN1DFB2, FB4
22.2uFCapacitor_SMD:C_0603_1608MetricC12, C64
22.2uHInductor_SMD:L_Bourns_SRP4020TAL1, L2
220pFCapacitor_SMD:C_0402_1005MetricC48, C54
2220pFCapacitor_SMD:C_0603_1608MetricC9, C21
222RResistor_SMD:R_0402_1005MetricR2, R3
23V3TestPoint:TestPoint_Pad_D1.0mmTP1, TP6
2470kResistor_SMD:R_0402_1005MetricR48, R54
249.9RResistor_SMD:R_0603_1608MetricR11, R17
25.1kResistor_SMD:R_0402_1005MetricR1, R5
2GNDTestPoint:TestPoint_Pad_D1.0mmTP21, TP22
2LBSS138WT1GPackage_TO_SOT_SMD:SOT-323_SC-70Q2, Q4
2MMICT390200012Onju:MIC_T3902MK1, MK2
2PESD0402V05Diode_SMD:D_0402_1005MetricD3, D4
2SK6812D-EC3210ROnju:LED-SMD_4P_SK6812D-EC3210RLED1, LED6
2TPS62130Package_DFN_QFN:VQFN-16-1EP_3x3mm_P0.5mm_EP1.68x1.68mm_ThermalViasU3, U7
10RResistor_SMD:R_1206_3216MetricR66
10RResistor_SMD:R_0603_1608MetricR67
11.0pF DNPCapacitor_SMD:C_0201_0603MetricC110
11.2pFCapacitor_SMD:C_0402_1005MetricC28
110uFCapacitor_SMD:C_0402_1005MetricC40
1120pFCapacitor_SMD:C_0402_1005MetricC100
114VTestPoint:TestPoint_Pad_D1.0mmTP18
11775443-2Onju:1775443-2J5
11V8TestPoint:TestPoint_Pad_D1.0mmTP4
11kResistor_SMD:R_0402_1005MetricR57
11uHInductor_SMD:L_Murata_DFE201610PL8
12.2nHInductor_SMD:L_0402_1005MetricL5
12.4pFCapacitor_SMD:C_0402_1005MetricC36
12.7nHInductor_SMD:L_0402_1005MetricL4
1210kResistor_SMD:R_0603_1608MetricR12
122.1kResistor_SMD:R_0603_1608MetricR19
1220uFCapacitor_SMD:C_Elec_6.3x7.7C89
12450AT18A100ERF_Antenna:Johanson_2450AT18x100AE1
124MHz 12pFOnju:X4-SMD-2.0X1.6MMX1
13.3kResistor_SMD:R_0402_1005MetricR53
13.3nHInductor_SMD:L_0402_1005MetricL3
130RResistor_SMD:R_0603_1608MetricFB1
1330kResistor_SMD:R_0402_1005MetricR77
14.7uFCapacitor_SMD:C_0805_2012MetricC20
140MHzCrystal:Crystal_SMD_2016-4Pin_2.0x1.6mmY1
140kResistor_SMD:R_0603_1608MetricR13
151kResistor_SMD:R_0402_1005MetricR74
15VTestPoint:TestPoint_Pad_D1.0mmTP17
15V_SWTestPoint:TestPoint_Pad_D1.0mmTP3
1600ROnju:BLM18PG121SN1DFB5
168.1kResistor_SMD:R_0603_1608MetricR18
1680RResistor_SMD:R_0402_1005MetricR35
174AHCT1G125Package_TO_SOT_SMD:SOT-353_SC-70-5U19
175kResistor_SMD:R_0402_1005MetricR72
1AP22802AW5-7Package_TO_SOT_SMD:SOT-23-5U4
1BC847BPackage_TO_SOT_SMD:SOT-23Q3
1BOOTOnju:SW-SMD_4P-L4.2-W3.2-P2.15-LS4.5SW2
1BOOTTestPoint:TestPoint_Pad_D1.0mmTP20
1ESP32-S3R8Onju:QFN40P700X700X90-57NU8
1FH34SRJ-10S-0.5SH_50_Onju:HRS_FH34SRJ-10S-0.5SH_50_POWER_IN1
1FH34SRJ-12S-0.5SH(50)Onju:HRS_FH34SRJ-12S-0.5SH_50_J6
1LBSS138WT1GOnju:SC-70-3_L2.1-W1.3-P0.65-LS2.1-BRQ1

The 223 most common of 249 parts.

Similar boards

  • 4 layers74.5 × 70.3 mmNest mini v2-drop in pcb, the printed circuit board in 3D

    Nest mini v2-drop in pcb

    iMike78/nest-mini-drop-in-pcb

    Drop-in PCB replacement for the Google Nest Mini v2 with ESP32-S3, ESP32-P4 and optional ESP32-C6. Inspired by Onju Voice and Home Assistant Voice PE.

    229 parts628CERN-OHL-S-2.0
  • 2 layers81.3 × 358.6 mmSlave Board, the printed circuit board in 3D

    Slave Board

    jayalcock/Clocks

    A million times clock project

    101 parts
  • 2 layers144.9 × 59.8 mmMonkeys, the printed circuit board in 3D

    Monkeys

    PacketChat/MonkeyBadge

    This repository contains the hardware design files, badge code, and backend infrastructure code for the HushCon Winter 2023 badge.

    153 parts21
  • 2 layersMacropad, the printed circuit board in 3D

    Macropad

    moonbeeper/moonpad

    109 partsMIT
  • 4 layers26.1 × 32.5 mmReband, the printed circuit board in 3D

    Reband

    jibonaronno/documentsA

    It is required to change settings using SCLManager.exe when required for new setup.

    51 parts4
  • 8 layers42.2 × 67.2 mmOBC PCB, the printed circuit board in 3D

    OBC PCB

    timohueser/OpenBikeComputer

    Open source Bikecomputer with a focus on exploration and adventure.

    186 parts11GPL-3.0

Questions

How big is the Nest mini v2-drop in pcb PCB?

It measures 74.5 × 70.3 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Nest mini v2-drop in pcb use?

249 parts, built around the 74AHCT1G125SE, ESP32-S3R8, TPS62130RGT and CC0603KRX7R9BB104. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Nest mini v2-drop in pcb KiCad files?

From the marceldale/nest-mini-v2-voice repository on GitHub, at the commit this page was made from: the board is nest-mini-v2-drop-in-pcb.kicad_pcb and its schematic audio.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Nest mini v2-drop in pcb design in my own project?

Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).