Skip to the content
2 layers15 × 6.5 mm3DS C, the printed circuit board in 3D

USB Type C conversion board for original 3DS consoles

Size
15 × 6.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
6
Nets
4
Pads
22
Tracks, vias
55, 5
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
29 Aug 2020
Updated
24 Dec 2021

Overview

3DS C is an open-source printed circuit board by makhowastaken, from the makhowastaken/3DS_C repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 15 × 6.5 mm with 6 parts on 4 nets, routed with 55 tracks and 5 vias.

It is built around the TYPE-C-31-M-17. Its parts include 2 resistors and 2 connectors.

Main components

1

README

README.md

3DS_C

USB Type C conversion board for original 3DS consoles

INSTALL AT YOUR OWN RISK!

These worked perfectly fine for me but I have had several reports of blown fuses. The parts are extremely close together and at very high risk of short with improper handling or install. Consider omitting the pads for the dock charger. The wider USB C port makes clearance very tight and without proper insulation, the pad WILL short on the body (ground) of the port. Again, it worked for me but it's really tight.


You can order some boards from ohspark here or use the supplied gerber file zip to upload to your preferred fab (does use castellated holes). I tested this successfully with 0.8mm PCBs

Otherwise all you need are the USB Type C ports: Aliexpress or LCSC

And two optional (for Type C Host charging only) 5.1k 0603 resistors.

For install, you will need to completely desolder the original port and file out the opening with needle files as the type C port is bigger than the OEM charge port. Solder the port to the new board, solder the optional resistors, then solder the board to the 3DS. I have also included pads to transplant the original pads for the dock charger but due to the size of the type C port, it's not recommended. See my install below for more info or better instruction.

YouTube install: https://www.youtube.com/watch?v=8TaaZng31x4

front

back

20210701_202321.jpg

20210701_202325.jpg

Parts

6
QtyValueFootprintReferences
25.1KResistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolderR1, R2
2VCCTestPoint:TestPoint_THTPad_1.5x1.5mm_Drill0.7mmVCC, VCC
13DS_POWERmisc_footprints:3DS_POWERJ2
1TYPE-C-31-M-17misc_footprints:TYPEC31M17J1

Similar boards

  • 2 layers82 × 42 mmOpen authenticator, the printed circuit board in 3D

    Open authenticator

    Open-Authenticator/hardware-design

    Hardware design files for open authenticator

    86 parts42MIT
  • 4 layersWatchBorad, the printed circuit board in 3D

    WatchBorad

    ValentiWorkLearning/GradWork

    Development board based on NRF52832 E73 module with C++20/CMake/VSCode based development flow

    119 parts39MIT
  • 2 layers100 × 100 mmHeatTable Base v0.9, the printed circuit board in 3D

    HeatTable Base v0.9

    DerSpatz/PCB-reflow-solder-table

    Table version of the PCB heat plate with advanced features and swappable heat plate

    82 parts14MIT
  • 4 layers268 × 152 mmDrumboy Main, the printed circuit board in 3D

    Drumboy Main

    Randomwaves/Drumboy-Pro

    📖 Developer Wiki — full hardware specs, schematics walkthrough, firmware architecture, DSP internals, and memory map.

    346 parts10MIT
  • 2 layers65 × 56 mm5ghz wifibroadcast hat, the printed circuit board in 3D

    5ghz wifibroadcast hat

    roman-koshchei/5ghz_wifibroadcast_hat

    5GHz WiFibroadcast HAT for FPV video transmission, long-range comms, WFB-NG, network analysis and Monitor Mode

    18 parts7CERN-OHL-S-2.0
  • 4 layers50 × 40 mmLlm kicad, the printed circuit board in 3D

    Llm kicad

    fgihl/usb-c-one

    Small one port USB-C hub, similar to YKUSH XS, but uses USB-C connectors

    100 parts
  • 2 layers38.5 × 27.5 mmUsbc2dell, the printed circuit board in 3D

    Usbc2dell

    H3wastooshort/usbc2dell

    USB-C PD to Dell Barrel-Jack adapter

    30 partsGPL-3.0

Questions

How big is the 3DS C PCB?

It measures 15 × 6.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the 3DS C use?

6 parts, built around the TYPE-C-31-M-17. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the 3DS C KiCad files?

From the makhowastaken/3DS_C repository on GitHub, at the commit this page was made from: the board is 3DS_C.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the 3DS C design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).