Skip to the content
2 layersBattleSync, the printed circuit board in 3D
Copper layers
2
Thickness
1.6 mm
Parts
15
Nets
35
Pads
70
Tracks, vias
84, 3
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
6 Aug 2025
Updated
24 Oct 2025

Overview

BattleSync is an open-source printed circuit board by Majawat, from the Majawat/BattleAura repository on GitHub. It is a 2-layer board with 15 parts on 35 nets, routed with 84 tracks and 3 vias.

It is built around the DFR0299 and ESP32-S3. Its parts include 9 diodes, 2 ICs, 1 capacitor and 1 switch. It belongs with the ESP32 boards of this library.

Main components

2

README

README.md

BattleAura

LED and Sound Controller for wargaming miniatures

Parts

  • Seeed Studio Xiao ESP32-S3 dev board
  • DFRobot DFPlayer Mini
  • microSD card
  • LEDs (single LEDs and WS2812B)
  • Speaker (8ohm)
  • 14500 Battery

Wiring Notes

  • ESP32 GPIO43 (D6/TX) -> DFPlayer RX
  • ESP32 GPIO44 (D7/RX) -> DFPlayer TX
  • GPIO 1-9 pins to LEDs+, GND
  • Speaker +/1 to DFPlayer
  • Battery direct to ESP32-S3 battery terminals, WS2812B, and DFPlayer

LEDS

LED Pin assignment

  • D0: Candle Fibers 1 - 3mm warm white, 3v
  • D1: Candle Fibers 2 - 3mm warm white, 3v
  • D2: Candle Fibers 3 - 3mm warm white, 3v
  • D3: Console screen - WS2812B RGB, 5v
  • D4: Machine Gun - Nano (1.6mm) warm white, 3v
  • D5: Flamethrower - Nano (1.6mm) warm white, 3v
  • D8: Engine stack 1 - Chip (3.2mm) warm white, 3v
  • D9: Engine stack 2 - Chip (3.2mm) warm white, 3v
  • D10: Brazier - Chip (3.2mm) warm white, 3v

Audio files assignments

  • 0001 - Tank engine idle 1
  • 0002 - Tank engine idle 2
  • 0003 - Machine gun fire
  • 0004 - Flamethrower
  • 0005 - Taking hits
  • 0006 - Engine revving
  • 0007 - Destroyed
  • 0008 - Rocket Launcher
  • 0009 - Killed other unit

Audacity settings

  • Track > Mix > Mix stero down to Mono
  • Track > Resample > 22050 Hz
  • Effect > Normalize > -1dB
  • Export as MP3

Parts

15
QtyValueFootprintReferences
8LEDConnector_Wire:SolderWire-0.1sqmm_1x02_P3.6mm_D0.4mm_OD1mmD1, D2, D3, D4, D5, D6, D7, D8
1Battery_CellConnector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_VerticalBT2
1C_PolarizedCapacitor_THT:CP_Radial_D4.0mm_P2.00mmC1
1DFR0299DFR0299:MODULE_DFR0299U2
1ESP32-S3RF_Module:MCU_Seeed_ESP32C3U1
1LEDConnector_Wire:SolderWire-0.1sqmm_1x03_P3.6mm_D0.4mm_OD1mmD9
1SW_SPDTConnector_Wire:SolderWire-0.1sqmm_1x02_P3.6mm_D0.4mm_OD1mmSW1
1SpeakerConnector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_VerticalLS1

Similar boards

  • 2 layers104.7 × 135.6 mmDiscAdventure, the printed circuit board in 3D

    DiscAdventure

    Trikkitt/polygen

    PolyGen game repository

    61 parts13
  • 2 layers145.4 × 70 mmLab64 vday musicbox, the printed circuit board in 3D

    Lab64 vday musicbox

    angelinakrinos/lab64_vday

    🚀 Enjoy your Valentine's Day Music Box! 🎶❤️

    16 parts4
  • 2 layers48.2 × 28.3 mmLoop, the printed circuit board in 3D

    Loop

    ayaangrover/loop

    a low-cost mp3 player

    11 parts3MIT
  • 2 layers210 × 140 mmGifu creation koubou, the printed circuit board in 3D

    Gifu creation koubou

    kinoshita-lab/gifu-creation-koubou-teaching-material

    109 parts3MIT
  • 2 layers9 × 25 mmModularPowerSupply, the printed circuit board in 3D

    ModularPowerSupply

    Animal-Crate/Animal-Crate

    This is a public repository for the Animal Crate project. Please review the README for more information.

    35 parts2AGPL-3.0
  • 2 layers99.1 × 99.1 mmBs base, the printed circuit board in 3D

    Bs base

    MelexinVN/bs_kombo_bs

    Электронная беспроводная система для проведения интеллектуальных игр на микроконтроллерах stm32 и радиомодулях nrf24l01+.

    30 parts2GPL-3.0
  • 2 layers25 × 100 mmLightsaber, the printed circuit board in 3D

    Lightsaber

    BamdadKh/ArduinoLightsaber

    A lightsaber prop built around an Arduino Nano on a custom PCB. It has a 144-LED blade, sound from a DFPlayer Mini, swing detection with an MPU-6050, a small OLED and two buttons. I built it for a Halloween costume.

    15 parts1MIT
  • 2 layers127 × 83.5 mmAudiostation, the printed circuit board in 3D

    Audiostation

    janikkaden/self-sufficient-audio-station

    A solar-powered, self-sufficient audio station for outdoor exhibitions — ESP32 + DFPlayer, wakes from deep sleep on a button press and plays info tracks in three languages plus music.

    28 parts1GPL-3.0

Questions

What parts does the BattleSync use?

15 parts, built around the DFR0299 and ESP32-S3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the BattleSync KiCad files?

From the Majawat/BattleAura repository on GitHub, at the commit this page was made from: the board is kicad_files/BattleSync.kicad_pcb and its schematic kicad_files/BattleSync.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the BattleSync design in my own project?

Its repository states no licence, so its author keeps all rights: ask Majawat before reusing the design.