Skip to the content
2 layers76.2 × 76.2 mmCorner board wson6, the printed circuit board in 3D

Corner board wson6

lutetjeff/ece395

Repository for UIUC ECE395 project known as RHipoff. A mixture of the Rhythm Horizon and RE:Flex Dance platforms built from the ground up.

Size
76.2 × 76.2 mm
Copper layers
2
Thickness
1.6 mm
Parts
61
Nets
42
Pads
185
Tracks, vias
568, 72
Pours
4
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
22 Oct 2024
Updated
14 Dec 2024

Overview

Corner board wson6 is an open-source printed circuit board by lutetjeff, from the lutetjeff/ece395 repository on GitHub. It is a 2-layer board of 76.2 × 76.2 mm with 61 parts on 42 nets, routed with 568 tracks and 72 vias.

It is built around the BAT54S. Its parts include 16 resistors, 12 capacitors, 6 diodes, 6 connectors and 4 ICs. It belongs with the STM32 boards of this library.

Main components

1

README

README.md

Repository for UIUC ECE395 project known as RHipoff. A mixture of the Rhythm Horizon and RE:Flex Dance platforms built from the ground up. Current configuration is for four load cells only, but firmware supports up to 16 different panels with four load cells each.

Parts

61
QtyValueFootprintReferences
9100nCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC3, C4, C5, C7, C8, C9, C10, C11, C12
71kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR8, R9, R10, R11, R12, R15, R16
42.2Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR4, R5, R6, R7
4BAT54SPackage_TO_SOT_SMD:SOT-23D1, D2, D3, D4
210kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR13, R14
21k 0.1%Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR1, R2
2SW_PushButton_Switch_THT:SW_PUSH_6mmSW2, SW3
1120Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR3
11uCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC1
12.2uCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC2
1220nCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC6
1ADS131M04IPWTfootprints:PW20_TEXU4
1GREENLED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolderD6
1LOAD CELL 1Connector_JST:JST_XH_S3B-XH-A_1x03_P2.50mm_HorizontalJ2
1LOAD CELL 2Connector_JST:JST_XH_S3B-XH-A_1x03_P2.50mm_HorizontalJ3
1LOAD CELL 3Connector_JST:JST_XH_S3B-XH-A_1x03_P2.50mm_HorizontalJ4
1LOAD CELL 4Connector_JST:JST_XH_S3B-XH-A_1x03_P2.50mm_HorizontalJ5
1MAINConnector_JST:JST_XH_S6B-XH-A_1x06_P2.50mm_HorizontalJ1
1PTCAN3414DRfootprints:SOIC8_D_TEXU3
1STM32F042F6PxPackage_SO:TSSOP-20_4.4x6.5mm_P0.65mmU1
1SWDConnector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_VerticalJ6
1SW_DIP_x04Button_Switch_THT:SW_DIP_SPSTx04_Slide_6.7x11.72mm_W7.62mm_P2.54mm_LowProfileSW1
1TLV76733DRVxPackage_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm_ThermalViasU2
1YELLOWLED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolderD5

The 47 most common of 61 parts.

More from lutetjeff/ece395

2
  • 2 layers89.5 × 76.5 mm395MainBoard, the printed circuit board in 3D

    395MainBoard

    lutetjeff/ece395

    Repository for UIUC ECE395 project known as RHipoff. A mixture of the Rhythm Horizon and RE:Flex Dance platforms built from the ground up.

    45 parts
  • 2 layers27.9 × 40.6 mmEx4, the printed circuit board in 3D

    Ex4

    lutetjeff/ece395

    Repository for UIUC ECE395 project known as RHipoff. A mixture of the Rhythm Horizon and RE:Flex Dance platforms built from the ground up.

    25 parts

Similar boards

  • 2 layers58.2 × 38.1 mmUsb sniffer, the printed circuit board in 3D

    Usb sniffer

    ataradov/usb-sniffer

    Low-cost LS/FS/HS USB sniffer with Wireshark interface

    87 parts1.3kBSD-3-Clause
  • 4 layers94.4 × 72.8 mmRP2040 base, the printed circuit board in 3D

    RP2040 base

    Twisted-Fields/rp2040-motor-controller

    A dual channel brushless motor controller based on the RP2040 microcontroller, designed in Kicad.

    325 parts419
  • 4 layers72.4 × 95.3 mmDingoPDM, the printed circuit board in 3D

    DingoPDM

    corygrant/dingoPDM

    Hardware - dingoPDM is an open source, affordable automotive PDM (Power Distribution Module). Pre-assembled and tested units are available or the design can be used to build a DIY version.

    156 parts128MIT
  • 2 layers100 × 99.8 mmUnderdog, the printed circuit board in 3D

    Underdog

    turboedge/SpeedyBoards

    EMS boards powered by Speeduino

    396 parts110GPL-2.0
  • 6 layers203 × 151.8 mmPDNode Baseboard, the printed circuit board in 3D

    PDNode Baseboard

    DvidMakesThings/HW_PDNode-600-Pro

    The PDNode-600 is a professional-grade, 600W USB Power Delivery Unit designed specifically for compact 10-inch rack systems, targeting embedded developers, homelab enthusiasts, test benches, and smart infrastructure.

    236 parts86AGPL-3.0
  • 6 layers71.5 × 63.6 mmSensorboard, the printed circuit board in 3D

    Sensorboard

    CameraNexus/sitina1

    Open-source 35mm full-frame (36mm x 24mm) CCD mirror-less interchangable lens camera (MILC). The original goal of this project was to create a digital camera back to convert SLR cameras to DSLR cameras, but has since…

    426 parts82MIT
  • 2 layers248.9 × 120.7 mm16nx, the printed circuit board in 3D

    16nx

    16n-faderbank/16nx

    16nx is a controller for musical instruments. Sixteen faders,MIDI over USB and jack, CV out, and I2C out. Based around RP2040.

    171 parts76
  • 4 layers137 × 79.5 mmTGX4, the printed circuit board in 3D

    TGX4

    hexeguitar/TGX4

    Teensy 4 based guitar amp emulator

    297 parts66

Questions

How big is the Corner board wson6 PCB?

It measures 76.2 × 76.2 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Corner board wson6 use?

61 parts, built around the BAT54S. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Corner board wson6 KiCad files?

From the lutetjeff/ece395 repository on GitHub, at the commit this page was made from: the board is corner-board/corner-board-wson6.kicad_pcb and its schematic 395MainBoard/395MainBoard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Corner board wson6 design in my own project?

Its repository states no licence, so its author keeps all rights: ask lutetjeff before reusing the design.