
SV PWM card R01
mariusenglund/three-phase-inverter
Materials for enhancing the DC-to-AC converter that was designed as part of our bachelor's thesis in the spring of 2023.

Design and Control of a Solar-Powered Irrigation System for Remote Farmlands
SolarSystem is an open-source printed circuit board by louieoneil19, from the louieoneil19/Thesis repository on GitHub. It is a 4-layer board of 217.2 × 201.5 mm with 71 parts on 136 nets, routed with 436 tracks and 72 vias.
It is built around the TC4420CPA, ACPL-C87B-000E and HCPL-2211-000E, with the SK34SMA-3G, IRLZ44NSTRLPBF and SRR1210-471M among its other parts. Its parts include 10 diodes, 9 ICs, 2 capacitors, 2 resistors and 2 inductors. It belongs with the power boards of this library.
An STM32-based MPPT buck-boost converter for solar-powered soil moisture monitoring and pump control.
This project presents the design and implementation of a solar-powered irrigation system optimised for off-grid rural use. The system integrates a photovoltaic panel, a non-inverting DC–DC buck-boost converter, a backup battery, a water pump, and a microcontroller-based control unit on a custom four-layer printed circuit board. A perturb-and-observe maximum power point tracking (MPPT) algorithm is implemented to maximise energy extraction from the solar panel across varying irradiance and temperature conditions. A capacitive soil moisture sensor drives a separate pump-control loop, varying pump speed in discrete stages based on measured soil dryness. The converter was validated in MATLAB Simulink and characterised experimentally through duty-cycle sweeps, with the measured input–output relationships closely matching theoretical predictions. The completed system demonstrates autonomous solar energy harvesting and adaptive water delivery, providing a viable platform for off-grid agricultural applications in resource-limited regions.
.
├── firmware/ STM32CubeIDE project (STM32F446RE)
│ ├── Core/ Application source code (main.c, peripherals)
│ ├── Drivers/ STM32 HAL drivers
│ └── *.ioc STM32CubeMX configuration
│
└── hardware/ KiCad PCB design
├── SolarSystem/ KiCad project files (schematic + PCB layout)
├── gerbers/ Manufacturing files for PCB fabrication
├── libraries/ Custom footprints and symbols
├── SolarSystem Layout.pdf PDF file of SolarSystem schematics
└── SolarSystem_BOM.csv Bill of materialsThe primary application logic lives in:
This file contains all the custom application code, including:
Run_MPPT(), track_mpp_20_seconds()Run_IV_Sweep()Read_Panel_Sensors(), Process_ADC_Buffer()Run_Soil_Moisture_Control(), find_moisture_calibration()Set_Converter_Duty(), Set_Manual_Duties()find_calibration_values()Print_Panel_Sensors()The other files in firmware/Core/Src/ (such as stm32f4xx_hal_msp.c, stm32f4xx_it.c, syscalls.c, sysmem.c, and system_stm32f4xx.c) are auto-generated by STM32CubeMX and contain HAL initialisation and system-level boilerplate — they generally don't need to be modified.
Requirements:
Steps:
firmware/ folder in this repositoryThe PCB design is created in KiCad (free, open-source).
To view the schematic and PCB layout:
hardware/SolarSystem/ and double-click the .kicad_pro fileManufacturing files:
The hardware/gerbers/ folder contains ready-to-fabricate Gerber files compatible with most PCB manufacturers (JLCPCB, PCBWay, OshPark, etc.).
Louie O'Neil
This project is shared as part of academic thesis work. See LICENSE for details.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | Conn_01x01 | Connector:Banana_Jack_1Pin | J_BAT-1, J_BAT+1, J_M1-1, J_M1+1, J_M2-1, J_M2+1, J_M3-1, J_M3+1, J_Pump-1, J_Pump+1, J_PV-1, J_PV+1, J_VDD1-1, J_VDD1+1 |
| 8 | 100nF | GRM033R6YA104KE14D:CAPC0603X33N | Cb1, Cb4, Cb5, Cb6, Cd2, Cd4, Cvs2, Cvs3 |
| 5 | 10uF | AGC1210X7R500-106KNE:CAPC3225X280N | Cd1, Cd3, Cpv1, Cpv2, Cpv3 |
| 4 | SK34SMA-3G | SK34SMA-3G:DIOM5027X240N | D1, D2, D3, D4 |
| 3 | 10R | RC0805FR-0710RL:RESC2012X60N | Rd2, Rd6, Rd10 |
| 3 | 1N4148 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D5, D7, D9 |
| 3 | 220R | RN73H2ATTD2200F100:RESC2012X60N | Rd1, Rd5, Rd9 |
| 3 | 22R | CR0805-JW-220ELF:RESC2012X60N | Rd4, Rd8, Rd12 |
| 3 | 5k6 | RG2012P-562-B-T5:RESC2012X50N | Rd3, Rd7, Rd11 |
| 3 | HCPL-2211-000E | HCPL-2211-000E:SO-8_AVA | U3, U5, U7 |
| 3 | IRLZ44NSTRLPBF | IRLZ44NSTRLPBF:NMOSGDS_D2PAK_INF | M1, M2, M3 |
| 3 | MM5Z15VT1G | MM5Z15VT1G:SODFL1608X70N | D6, D8, D10 |
| 3 | TC4420CPA | TC4420CPA:PDIP8_300MC_MCH | U4, U6, U8 |
| 2 | 1uF | AGC0603X7R250-105KXP:CAPC1608X95N | Cb2, Cb3 |
| 1 | 100pF | GRM0335C1H101JA01D:CAPC0603X33N | Cvs1 |
| 1 | 10k | RN73H2ATTD1002B25:RESC2012X60N | R2 |
| 1 | 10nF | GRM155R71C103KA01D:CAPC1005X55N | CL1 |
| 1 | 98k | RN73H2ATTD9882A25:RESC2012X60N | R1 |
| 1 | ACPL-C87B-000E | ACPL_C87B_000E:SOIC127P1150X360-8N | IC1 |
| 1 | ACS722xLCTR-05AB | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | ATB107M035 | ATB107M035:CAPAE660X800N | C1 |
| 1 | NUCLEO-F446RE | NUCLEO-F446RE:MODULE_NUCLEO-F446RE | U1 |
| 1 | SRR1210-471M | SRR1210-471M:IND_BOURNS_SRR1210 | L2 |
| 1 | WCAP-ASLI_4X5.5 | 865080540002:WCAP-ASLI_4X5.5_DXL_ | C2 |
| 1 | WE-HCF_2920_ROUND | WE-HCF_2920_ROUND:WE-HCF_2920_ROUND | L1 |

mariusenglund/three-phase-inverter
Materials for enhancing the DC-to-AC converter that was designed as part of our bachelor's thesis in the spring of 2023.

JanBotnen/Three-phase-inverter_Modification
Design and implementation of a three-phase inverter with SPWM and SVPWM, prepared for future PMSM control.





OakTreeWC/ESPLEDDriver-v1.0
ESP Powered LED Driver Board for both Addressable and Non-Addressable LEDs.

r-map/rmap
rete monitoraggio ambientale partecipativo documentation at https://doc.rmap.cc
It measures 217.2 × 201.5 mm and has 4 copper layers, 0.19 mm thick.
71 parts, built around the TC4420CPA, ACPL-C87B-000E, HCPL-2211-000E and SK34SMA-3G. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the louieoneil19/Thesis repository on GitHub, at the commit this page was made from: the board is hardware/SolarSystem/SolarSystem/SolarSystem.kicad_pcb and its schematic hardware/SolarSystem/SolarSystem/Buck_Converter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask louieoneil19 before reusing the design.