Skip to the content
4 layers90 × 75 mmFenix controlador de ressolda, the printed circuit board in 3D

Fenix controlador de ressolda

lcmaquino/fcr1

The FCR software controls the temperature of two heating devices for preheating electronic boards or reballing BGA components.

Size
90 × 75 mm
Copper layers
4
Thickness
1.6 mm
Parts
27
Nets
43
Pads
96
Tracks, vias
186, 1
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
6 Jan 2025
Updated
25 Jun 2025

Overview

Fenix controlador de ressolda is an open-source printed circuit board by lcmaquino, from the lcmaquino/fcr repository on GitHub. It is a 4-layer board of 90 × 75 mm with 27 parts on 43 nets, routed with 186 tracks and 1 via.

It is built around the MAX6675ISA+, LM1117MP-3.3 and BC548. Its parts include 8 resistors, 8 connectors, 4 transistors, 1 IC and 1 diode. It belongs with the RP2040 boards of this library.

Main components

3

README

README.md

Description

The Fenix Reballing Controller (FCR) software controls the temperature of two heating devices for preheating electronic boards or reballing BGA components. Examples of heating devices include an electric grill or an electric resistor. Due to the high electrical current required to power these devices, they should be activated via a mechanical relay or a solid-state relay.

The FCR consists of an electronic circuit with the Raspberry Pi Pico microcontroller and a set of codes written for MicroPython.

Assembly and Installation

  • Assemble the electronic circuit according to the schematic diagram: fenix-controlador-de-ressolda.pdf. Also, see the simple wiring diagram;
  • Connect the relay input pins to the connectors indicated in the diagram by OUT1 and OUT2;
  • Connect the relay output pins to the heating devices;
  • Connect the HD44780 LCD 16×02, MAX6675, and Keyes_AD_Key modules to their respective connectors indicated in the diagram;
  • Install the MicroPython firmware on the Raspberry Pi Pico;
  • Use your preferred IDE to copy all files from the src directory to the Raspberry Pi Pico. (For example, you can use Thonny or Visual Studio Code);
  • Power the electronic circuit with a 5V DC power supply with at least 500mA;

The Keyes_AD_Key module has five tactile switches labeled SW1, SW2, SW3, SW4, and SW5. The FCR maps these switches for menu navigation such that:

  • SW1 - moves the menu to the left;
  • SW2 - increases the value of the currently displayed option;
  • SW3 - decreases the value of the currently displayed option;
  • SW4 - moves the menu to the right;
  • SW5 - selects the current menu;

Usage

The FCR has three modes:

  • Preheater - for preheating an electronic board;
  • Reballing - for reballing BGA components;
  • Auto Tuning - to automatically calculate the coefficients used in the PID control;

All modes have a menu containing specific and general options.

The general options are:

  • Kp - proportional coefficient of the PID control;
  • Ki - integral coefficient of the PID control;
  • Kd - derivative coefficient of the PID control;
  • ap - actuation period is the period (in seconds) at which the PID control is updated;
  • Run - execute the mode functions;
  • Home - return to the initial mode selection screen;

See below the specific options for each mode.

Preheater Mode

The Preheater mode controls only one heating device that should be placed below the electronic board.

In Preheater mode, the specific options are:

  • SV - Setpoint Variable is the temperature (in degrees Celsius) that the heating element should reach;
  • d - duration is the duration (in seconds) the mode should run;

Reballing Mode

The Reballing mode controls two heating devices, one of which should be placed below the electronic board and the other above it.

In Reballing mode, the specific options are:

  • PTN - pattern is the temperature pattern (in degrees Celsius) that the heating devices should follow. Each pattern consists of up to five parts, each containing the r, L, and d options explained below;
  • r - rate is the rate of temperature change (in degrees Celsius per second);
  • L - limit is the temperature limit (in degrees Celsius) that should be reached;
  • d - duration is the duration (in seconds) that the temperature should remain at its limit L;

Up to 10 temperature patterns can be configured. Here is an example configuration:

text
  PTN1
  | - r1: 0.86
  | - L1: 120.0
  | - d1: 60
  | - r2: 0.57
  | - L2: 180.0
  | - d2: 60
  | - r3: 0.29
  | - L3: 210.0
  | - d3: 60
  | - r4: 0.19
  | - L4: 227.0
  | - d4: 60
  | - r5: 0.0
  | - L5: 0.0
  | - d5: 0

Note that in this example, the PTN1 pattern will have four active parts. The fifth part is all zeros and will be ignored by the FCR. The figure below represents this pattern.

Image of the graph representing the PTN1 pattern

In the first part of the pattern, the temperature should rise at a rate of r1 = 0.86°C/s until it reaches L1 = 120°C, staying at this temperature for d1 = 60s. In the second part, the temperature should rise at a rate of r2 = 0.57°C/s until it reaches L2 = 180°C, staying at this temperature for d2 = 60s. In the third part, the temperature should rise at a rate of r3 = 0.29°C/s until it reaches L3 = 210°C, staying at this temperature for d3 = 60s. Finally, in the fourth part, the temperature should rise at a rate of r4 = 0.19°C/s until it reaches L4 = 227°C, staying at this temperature for d4 = 60s.

Auto Tuning

The Auto Tuning mode analyzes the temperature data of the heating device below the electronic board to approximately calculate the Kp, Ki, and Kd coefficients of the PID controller.

In Auto Tuning mode, the specific options are:

  • SV - Setpoint Variable is the temperature (in degrees Celsius) that the heating element should reach;
  • d - duration is the duration (in seconds) the mode should run;

License

FCR is open-sourced software licensed under the GPL v3.0 or later.

Parts

27
QtyValueFootprintReferences
42.2KohmResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR3, R4, R7, R8
4BC548Package_TO_SOT_THT:TO-92_InlineQ1, Q2, Q3, Q4
2100RResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR2, R6
211.5KohmResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1, R5
11N5817Diode_THT:D_DO-41_SOD81_P10.16mm_HorizontalD1
1Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ5
1Conn_01x20Connector_PinSocket_2.54mm:PinSocket_1x20_P2.54mm_VerticalJ9
1HD44780 LCD16x02Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_VerticalJ2
1Keyes_AD_KeyConnector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_VerticalJ3
1LM1117MP-3.3Package_TO_SOT_SMD:SOT-223-3_TabPin2U1
1LOGOLOGOG***
1Max6675Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_VerticalJ4
1OUT1Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_VerticalJ6
1OUT2Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_VerticalJ7
1Raspberry Pi PicoConnector_PinSocket_2.54mm:PinSocket_1x20_P2.54mm_VerticalJ1

The 23 most common of 27 parts.

Similar boards

  • 2 layers129.9 × 63.6 mmTraeger rev 2.3.0.kicad pro, the printed circuit board in 3D

    Traeger rev 2.3.0.kicad pro

    jazzmonger/Traeger-PID-Controller

    Traeger Smoker/Grill Controller based on an

    45 parts36
  • 2 layers176 × 82.6 mmHotAirGun, the printed circuit board in 3D

    HotAirGun

    raspibo/HotAirGun

    Hot Air Gun File, 3D, Sch, Pcb, C

    78 parts16
  • 2 layers60 × 75 mmOSRO, the printed circuit board in 3D

    OSRO

    dragonlock2/OSRO

    Just another open-source reflow oven

    52 parts11Apache-2.0
  • 2 layers77.5 × 42.3 mmReflow, the printed circuit board in 3D

    Reflow

    atx/reflow-controller

    Reflow Oven Controller

    52 parts6GPL-3.0
  • 2 layers70 × 100 mmBREAD Slice, the printed circuit board in 3D

    BREAD Slice

    FHafting/BREAD

    This project is fully documented in the paper: Shane Oberloier, Nicholas G. Whisman, Finn Hafting, Joshua M. Pearce, Open Source Framework for a Broadly Expandable and Reconfigurable Data Acquisition and Automation…

    48 parts5
  • 2 layersSTM32CAN, the printed circuit board in 3D

    STM32CAN

    witoldo7/STM32CAN

    Trionic 5, 7, 8 flasher interface.

    50 parts5Apache-2.0
  • 2 layers71.1 × 35.1 mmBrilliant Reflow v0.1, the printed circuit board in 3D

    Brilliant Reflow v0.1

    LKbrilliant/Brilliant-Reflow

    A complete DIY solution for converting a consumer oven into a temperature controlled reflow oven for PCB soldering

    28 parts4MIT

Questions

How big is the Fenix controlador de ressolda PCB?

It measures 90 × 75 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Fenix controlador de ressolda use?

27 parts, built around the MAX6675ISA+, LM1117MP-3.3 and BC548. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Fenix controlador de ressolda KiCad files?

From the lcmaquino/fcr repository on GitHub, at the commit this page was made from: the board is pcb/fenix-controlador-de-ressolda.kicad_pcb and its schematic pcb/fenix-controlador-de-ressolda.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Fenix controlador de ressolda design in my own project?

Its repository states no licence, so its author keeps all rights: ask lcmaquino before reusing the design.