

Dev Board STM32G431
This is a custom dev board for a STM32G431
- Size
- 31.3 × 60.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 41
- Nets
- 57
- Pads
- 209
- Tracks, vias
- 719, 136
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 4 Jul 2026
- Updated
- 7 Aug 2026
Overview
Dev Board STM32G431 is an open-source printed circuit board by larshasstdas, from the larshasstdas/STM32G431-Dev-Board repository on GitHub, published under the MIT licence. It is a 2-layer board of 31.3 × 60.5 mm with 41 parts on 57 nets, routed with 719 tracks and 136 vias.
It is built around the USBLC6-2SC6. Its parts include 15 capacitors, 6 resistors, 4 connectors, 3 ICs and 3 diodes. It belongs with the microcontroller boards boards and the STM32 boards of this library.
Main components
1README
README.mdSTM32G431 Dev Board
A custom development board for the STM32G431CBT6 that referrences the NUCLEO-32 STM32G4 series board as well a WeAct STM32F405 Board. They only have the schematics and i changed a lot as well.
Motivation
I always had fun with designing PCBs but because the projects were always too expensive i never actually made them. I also have five STM32G431's laying around from a free samples and so i decided to design a development board for them.
Features
- USB-C with ESD protection
- LD39050PU33R a 3.3V LDO
- Reset, BOOT0 and user button
- 8 MHz HSE crystal (needs to be connected with a solder bridge)
- Power and user LED
PCB
The layout and size are similiar to the usual developement boards. All files for it are in the KiCad folder.
Bill of Materials
Prices are DigiKey unit prices. The 1×22 breakout was ordered as 24-pos strips and trimmed. I also ordered for five PCBs as that was the minimum amount on plcpcb so the real amount spent is around 5 times as much. I also added the price of the STM32 even though i already had it from free samples.
| Part | Description | Qty | Unit Price | Link |
|---|---|---|---|---|
| STM32G431CBT6 | MCU, Cortex-M4 170 MHz (LQFP-48) | 1 | €5.81 | DigiKey |
| LD39050PU33R | LDO 3.3V 500mA (DFN-6) | 1 | €0.68 | DigiKey |
| USB4105-GF-A | USB-C receptacle, 16P SMD R/A | 1 | €0.59 | DigiKey |
| USBLC6-2SC6 | USB ESD protection (SOT-23-6) | 1 | €0.29 | DigiKey |
| CPDQR5V0 | TVS diode 5V (SOD-923) | 1 | €0.38 | DigiKey |
| ABM8AIG-8.000MHZ | 8 MHz crystal (SMD 4-pin) | 1 | €1.07 | DigiKey |
| BLM18AG601SN1D | Ferrite bead 600Ω@100MHz (0603) | 1 | €0.04 | DigiKey |
| Header 2×4 R/A | Debug/SWD header 2.54mm (J1) | 1 | €0.56 | DigiKey |
| Header 1×22 vertical | Breakout headers 2.54mm (J3/J4) | 2 | €0.93 | DigiKey |
| PTS526SK15SMTR2 | Tactile switch SMD (RST/BOOT/USER) | 3 | €0.12 | DigiKey |
| LTST-C190TBKT | Blue LED (0603) | 1 | €0.10 | DigiKey |
| LTST-C191KRKT | Red LED (0603) | 1 | €0.08 | DigiKey |
| GMC21X5R106K50NT | Cap 10µF 50V X5R (0805) | 1 | €0.34 | DigiKey |
| CL21A475KAQNNNE | Cap 4.7µF 25V X5R (0805) | 1 | €0.05 | DigiKey |
| UMK107BJ105KA-T | Cap 1µF 50V X5R (0603) | 2 | €0.07 | DigiKey |
| C0603C104K5RACTU | Cap 100nF 50V X7R (0603) | 9 | €0.03 | DigiKey |
| GJM1555C1H6R8WB01D | Cap 6.8pF 50V C0G (0402) | 2 | €0.08 | DigiKey |
| RC0603FR-0710KL | Resistor 10k 1% (0603) | 1 | €0.02 | DigiKey |
| RC0603FR-075K1L | Resistor 5.1k 1% CC pull-downs (0603) | 2 | €0.02 | DigiKey |
| RC0603FR-072K2L | Resistor 2.2k 1% (0603) | 2 | €0.02 | DigiKey |
| RC0603FR-071KL | Resistor 1k 1% (0603) | 1 | €0.02 | DigiKey |
| PCB | Fabricated dev board | 1 | €4.07 | – |
| Total | €16.99 |
Flashing
To flash a programm there are two options:
- Use a ST-Link and connect it to the 4 pins that are needed (other side is USB)
- Use an USB-C cable, hold the BOOT button (middle one) and shortly press the RESET button (side of all the A GPIOs). After that let go of the BOOT button and you should hear a windows connecting sound.
Test Programm
The test programm that is in this project lets two different LEDs blink. One is the onboard LED and the other is powered by a GPIO. Only on of them blinks at a time and the blinking switches when pressing the onboard USER-button. I used VS Code and PlatformIO to flash the Programm.
Future Improvment
- Silkscreen to label the buttons
- Move the USB and ST-Link connectors to the other side for better protection
- change the side of the silkscreen for the pins or do it on both sides
Files
KiCad/ Schematic, PCB and project files
Gerber/ Fabrication output (Gerber, drill, BOM, CPL, DigiKeyBOM)
TestProgramm/ includes all files needed to run a short test programm
Pick&Place.csvThe DigiKey BOM doesn't include the STM32's as i have them already.
License
MIT — see LICENSE.
Parts
41| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C4, C5, C6, C7, C9, C10, C14, C15 |
| 2 | 1u | Capacitor_SMD:C_0603_1608Metric | C2, C8 |
| 2 | 2.2k | Resistor_SMD:R_0603_1608Metric | R2, R4 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 2 | 6.8p | Capacitor_SMD:C_0402_1005Metric | C12, C13 |
| 2 | Conn_01x22 | Connector_PinHeader_2.54mm:PinHeader_1x22_P2.54mm_Vertical | J3, J4 |
| 2 | SolderJumper_2_Bridged | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_Pad1.0x1.5mm | JP3, JP4 |
| 2 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1, JP2 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C11 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 4.7u | Capacitor_SMD:C_0805_2012Metric | C3 |
| 1 | 600R@100MHz | Inductor_SMD:L_0603_1608Metric | L1 |
| 1 | BOOT | Button_Switch_SMD:SW_SPST_TL3342 | SW2 |
| 1 | Conn_02x04_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Horizontal | J1 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | D_TVS | footprints:CPDQR | D1 |
| 1 | LDO | footprints:LD39050PU33R | U3 |
| 1 | LOGO | footprints:sleepingcat | G*** |
| 1 | RST | Button_Switch_SMD:SW_SPST_TL3342 | SW1 |
| 1 | STM32G431CBTx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |
| 1 | USER | Button_Switch_SMD:SW_SPST_TL3342 | SW3 |
| 1 | blue | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | red | LED_SMD:LED_0603_1608Metric | D3 |
Similar boards
- 4 layers16.9 × 119.4 mm

- 2 layers290.1 × 130 mm

- 4 layers95 × 55.5 mm

EinkPDA keyboard
TalismanDesign/PocketMage_PDA
An E-Ink PDA device using the ESP32 S3.
137 parts2kApache-2.0 - 4 layers299 × 127 mm

- 2 layers42 × 67 mm

- 2 layers134 × 88 mm

Tulipcc
shorepine/tulipcc
The Tulip Creative Computer and AMYboard - portable Python synthesizers
103 parts978 - 4 layers70.8 × 108 mm

- 4 layers28.2 × 26.1 mm

DongleHiderPlus PCB
LeoDJ/FW-EC-DongleHiderPlus
Framework Expansion Card that includes a USB hub to hide a bare dongle inside and still have a USB-A port externally
23 parts497CERN-OHL-W-2.0
Questions
How big is the Dev Board STM32G431 PCB?
It measures 31.3 × 60.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Dev Board STM32G431 use?
41 parts, built around the USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Dev Board STM32G431 KiCad files?
From the larshasstdas/STM32G431-Dev-Board repository on GitHub, at the commit this page was made from: the board is KiCad/Dev Board STM32G431.kicad_pcb and its schematic KiCad/Dev Board STM32G431.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Dev Board STM32G431 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).