4 layers162.4 × 126.5 mm
Grup3 Tarda Projecte Netejaparabrises
AidarIglesias/Projecte_Neteja_Parabrises
El sistema ha de complir les seguents especificacions:
97 parts
4 layers56.8 × 52.6 mm
CAN Sensor Hub v1
landonh12/SensorHubBoardAn I2C/DIO/AIO<->CAN Hub board for FRC applications
- Size
- 56.8 × 52.6 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 87
- Nets
- 119
- Pads
- 364
- Tracks, vias
- 767, 119
- Pours
- 19
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 20 Jun 2025
- Updated
- 5 Jul 2025
Overview
CAN Sensor Hub v1 is an open-source printed circuit board by landonh12, from the landonh12/SensorHubBoard repository on GitHub. It is a 4-layer board of 56.8 × 52.6 mm with 87 parts on 119 nets, routed with 767 tracks and 119 vias.
It is built around the TCAN1042DRQ1, TPS5430DDA and W25Q128JVSIQ, with the TPD4E05U06DQAR among its other parts. Its parts include 28 capacitors, 17 resistors, 10 connectors, 6 ICs and 5 diodes. It belongs with the sensors and measurement boards and the STM32 boards of this library.
Main components
4
TCAN1042DRQ1
SOIC-8-55℃~+125℃ 4.5V~5.5V 5Mbps 5uA 70mA CAN FD Transceiver SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN Transceivers
TPS5430DDA
ESOP-8-40℃~+125℃@(TJ) 1 1.221V~32.04V 3A 4.4mA 5.5V~36V 500kHz Adjustable Buck Buck Built-in No ESOP-8 DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
TPD4E05U06DQAR
USON-10-40℃~+125℃ 0.5pF 10nA 14V 2.5A@8/20us 40W@8/20us 5.5V 6.5V ESD Four channels IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Unidirectional USON-10(1x2.5) ESD and Surge Protection (TVS/ESD) ROHSTexas InstrumentsESD Protection Devices
Parts
87| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 100nF | Capacitor_SMD:C_0402_1005Metric | C10, C11, C12, C13, C14, C19, C21, C22, C25, C26, C27, C28 |
| 9 | TestPoint_Small | TestPoint:TestPoint_Pad_D0.5mm | TP10, TP11, TP12, TP13, TP14, TP15, TP16, TP17, TP18 |
| 7 | 10k | Resistor_SMD:R_0402_1005Metric | R8, R12, R13, R14, R15, R16, R17 |
| 4 | 10uF | Capacitor_SMD:C_0603_1608Metric | C17, C18, C23, C24 |
| 4 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5 | H1, H2, H3, H4 |
| 3 | 1k | Resistor_SMD:R_0402_1005Metric | R4, R5, R6 |
| 3 | 22 | Resistor_SMD:R_0805_2012Metric | R1, R2, R3 |
| 3 | Conn_01x04 | Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J1, J2, J3 |
| 3 | LED | LED_SMD:LED_0805_2012Metric | D1, D2, D3 |
| 2 | 2.2uF | Capacitor_SMD:C_0402_1005Metric | C8, C9 |
| 2 | 2pF | Capacitor_SMD:C_0402_1005Metric | C3, C4 |
| 2 | 4.3pF | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C15, C20 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R9, R10 |
| 2 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Horizontal | J9, J10 |
| 2 | D_Schottky | Diode_SMD:D_0603_1608Metric | D5, D6 |
| 2 | NMOS | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 1 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C5 |
| 1 | 100k | Resistor_SMD:R_0402_1005Metric | R18 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric | C6 |
| 1 | 15uH | Inductor_SMD:L_Sumida_CDMC6D28_7.25x6.5mm | L1 |
| 1 | 220uF | Capacitor_Tantalum_SMD:CP_EIA-3528-21_Kemet-B | C7 |
| 1 | 3.24k | Resistor_SMD:R_0402_1005Metric | R11 |
| 1 | 32.768KHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | X2 |
| 1 | 4.7uF | Capacitor_SMD:C_0805_2012Metric | C16 |
| 1 | 8MHz | Crystal:Crystal_SMD_3225-2Pin_3.2x2.5mm | X1 |
| 1 | AZ1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U4 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J11 |
| 1 | Conn_01x12 | TerminalBlock_WAGO:TerminalBlock_WAGO_2601-1112_1x12_P3.50mm_Horizontal | J12 |
| 1 | Conn_ARM_JTAG_SWD_10 | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J5 |
| 1 | NRST | lib:SW_TS-1088-AR02016 | SW1 |
| 1 | PMOS | Package_TO_SOT_SMD:SOT-23 | Q3 |
| 1 | STM32F722VETx | Package_QFP:LQFP-100_14x14mm_P0.5mm | U7 |
| 1 | TCAN1042DRQ1 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | TPD4E05U06DQA | Package_SON:USON-10_2.5x1.0mm_P0.5mm | U3 |
| 1 | TPS5430DDA | Package_SO:TI_SO-PowerPAD-8_ThermalVias | U1 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_GCT_USB4110 | J4 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U5 |
The 86 most common of 87 parts.
Similar boards
- 4 layers129 × 79.5 mm
- 2 layers278.7 × 107.5 mm
- 2 layers34.2 × 63.7 mm
Gb link usb
hazy2go/gb-link-usb
Game Boy (DMG) link port to USB-C PC adapter: printer emulation, PC link, online link play. Sister project of the WiFi Game Boy cart.
59 parts2 - 4 layers43 × 95 mm
Oe commutator controller
open-ephys/commutator-controller
Open Ephys commutator PCB and firmware
107 parts2 - 4 layers150 × 120 mm
Ephys test board
open-ephys/ephys-test-board
General purpose, automated electrophysiology test board
567 parts1 - 4 layers145.5 × 107.5 mm
- 4 layers48.1 × 41.6 mm
Questions
How big is the CAN Sensor Hub v1 PCB?
It measures 56.8 × 52.6 mm and has 4 copper layers, 1.6 mm thick.
What parts does the CAN Sensor Hub v1 use?
87 parts, built around the TCAN1042DRQ1, TPS5430DDA, W25Q128JVSIQ and TPD4E05U06DQAR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the CAN Sensor Hub v1 KiCad files?
From the landonh12/SensorHubBoard repository on GitHub, at the commit this page was made from: the board is CAN-Sensor-Hub-v1.kicad_pcb and its schematic CAN-Sensor-Hub-v1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the CAN Sensor Hub v1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask landonh12 before reusing the design.