Skip to the content
123456789999

TPS5430DDA

Texas InstrumentsExtended

-40℃~+125℃@(TJ) 1 1.221V~32.04V 3A 4.4mA 5.5V~36V 500kHz Adjustable Buck Buck Built-in No ESOP-8 DC-DC Converters ROHS

Part id
ti/TPS5430DDA
Category
DC DC Converters
Package
ESOP-8
Pins
9
In stock
3,502 at JLCPCB (C502477)
Used on
181 open-source boards

Overview

The TPS5430DDA is a DC DC Converter made by Texas Instruments in a ESOP-8 package with 9 pins. -40℃~+125℃@(TJ) 1 1.221V~32.04V 3A 4.4mA 5.5V~36V 500kHz Adjustable Buck Buck Built-in No ESOP-8 DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (Regulator_Switching:TPS5430DDA, from KiCad's library) and its footprint (Package_SO:TI_SO-PowerPAD-8, from KiCad's library), ready for a KiCad board. 3,502 are in stock at JLCPCB (part C502477). 181 open-source boards in 140 repositories on GitHub use it.

Symbol

1BOOT4VSENSE5EN6GND7VIN8PH9GNDPAD
Regulator_Switching:TPS5430DDAFrom KiCad's library

Footprint

123456789999
Package_SO:TI_SO-PowerPAD-8From KiCad's library

From the datasheet

14
Supply, least
5.5 V · VIN, recommended operating min · p. 4
Supply, most
36 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
40 V · VIN, absolute max · p. 4
Junction, hottest
150 °C · Operating virtual junction temperature, absolute max · p. 4
Takes working
2 mA · VIN quiescent current, typical, non-switching, VSENSE = 2V, PH open · p. 5
Takes asleep
15 µA · VIN shutdown current, typical, ENA = 0V · p. 5
Gives
3 A · Continuous output current, max · p. 1
Current limit
5 A · High-side peak current limit, typical · p. 5
Feedback reference
1.221 V · FB voltage, typical, TJ = 25°C · p. 5
Switches at
500 kHz · Switching frequency, typical · p. 5
Junction to air (DDA (HSOIC))
45 K/W · Junction-to-ambient, TPS5430EVM · p. 4
Junction to air (DDA (HSOIC))
42.3 K/W · Junction-to-ambient, JESD 51-7 · p. 4
Junction to case (DDA (HSOIC))
46 K/W · Junction-to-case, top · p. 4
Junction to board (DDA (HSOIC))
15 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

5
Output current
3A continuous, 4A peak · p. 1
Internal compensation
Minimizes external parts · p. 1
Switching frequency
Fixed 500kHz · p. 1
Protection
Overcurrent limiting, overvoltage protection, thermal shutdown · p. 8
Integrated bootstrap recharge diode
Included · p. 8

Around it

1
cap 0.01μF
between BOOT and PH; Low-ESR ceramic; X7R or X5R recommended; rated for at least 10V. · p. 10

Specifications

39
ParameterConditionsAs printedPage
Input voltageVIN(2) to GND, TPS5430min -0.3 · max 40 V4
Input voltageENA to GNDmin -0.3 · max 7 V4
Input voltageVSENSE to GNDmin -0.3 · max 3 V4
Output voltageBOOT to PH(3)min -0.3 · max 6 V4
Output voltagePH to GND, (Steady-state)(2), TPS5430min -0.6 · max 40 V4
Output voltagePH to GND, transient < 10nsmin -1.2 V4
Source currentPH Leakage currentmax 10 uA4
Operating virtual junction temperature TJmin -40 · max 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 Vmax 2000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±750 Vmax 750 V4
Input voltageInput voltage range, TPS5430min 5.5 · max 36 V4
Operating junction temperature TJmin -40 · max 125 °C4
Junction-to-ambient thermal resistance (TPS5430EVM) RθJADDA (HSOIC), 8 PINstyp 45 °C/W4
Junction-to-ambient thermal resistance (JESD 51-7) RθJADDA (HSOIC), 8 PINstyp 42.3 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)DDA (HSOIC), 8 PINstyp 46 °C/W4
Junction-to-board thermal resistance RθJBDDA (HSOIC), 8 PINstyp 15 °C/W4
Junction-to-top characterization parameter ψJTDDA (HSOIC), 8 PINstyp 5.2 °C/W4
Junction-to-board characterization parameter ψJBDDA (HSOIC), 8 PINstyp 15.3 °C/W5
Junction-to-case (bottom) thermal resistance RθJC(bot)DDA (HSOIC), 8 PINstyp 6 °C/W5
VIN quiescent current IQ(VIN)Non-switching, VSENSE = 2V, PH pin opentyp 2 · max 4.4 mA5
VIN shutdown supply current ISD(VIN)Shutdown, ENA = 0Vtyp 15 · max 50 uA5
VIN UVLO rising threshold VINUVLO(R)VVIN risingtyp 5.3 · max 5.5 V5
VIN UVLO hysteresis VINUVLO(H)typ 0.35 V5
FB voltage VFBTJ = 25°Cmin 1.202 · typ 1.221 · max 1.239 V5
FB voltage VFBTJ = –40°C to 125°Cmin 1.196 · typ 1.221 · max 1.245 V5
Switching frequency fSWmin 400 · typ 500 · max 600 kHz5
Minimum ON pulse width tON(min)typ 150 · max 200 ns5
Maximum duty cycle DMAXfSW = 500kHzmin 87 · typ 89 %5
ENA voltage rising threshold VEN(R)max 1.3 V5
ENA voltage falling threshold VEN(F)min 0.5 V5
ENA voltage hysteresis VEN(H)typ 325 mV5
Internal slow-start time (0 to 100%) tSSmin 5.4 · typ 8 · max 10 ms5
High-side peak current limit IHS(OC)min 4 · typ 5 · max 6 A5
Hiccup time before re-startmin 13 · typ 16 · max 20 ms5
High-side MOSFET on-resistance RDSON(HS)VIN = 12V, VBOOT-SW = 4.5Vtyp 100 · max 230 mΩ5
High-side MOSFET on-resistance RDSON(HS)VIN = 5.5V, VBOOT-SW = 4.0Vtyp 125 mΩ5
Thermal shutdown threshold TJ(SD)Temperature risingmin 135 · typ 162 °C5
Thermal shutdown hysteresis TJ(HYS)typ 14 °C5

Pins, by the datasheet

9
1 BOOT
High-side FET gate-driver boost capacitor connection; connect a 0.01uF low ESR capacitor to PH. · p. 3
2 NC
Not connected internally. · p. 3
3 NC
Not connected internally. · p. 3
4 VSENSE
Regulator feedback voltage; connect to output voltage divider. · p. 3
5 ENA
On/off control: below 0.5V stops switching, above 1.3V starts switching; may float using internal 1.5MΩ pullup; do not connect through a resistor to ground. · p. 3
6 GND
Ground; connect to DAP. · p. 3
7 VIN
Input supply; bypass to GND with a high quality low ESR ceramic capacitor within 1mm of both pins. · p. 3
8 PH
Source of the high side power MOSFET; connect to external inductor and diode. · p. 3
DAP DAP
Exposed pad; must connect to GND for proper operation. · p. 3

Open-source boards using it

181See all 181
  • 2 layers189.5 × 204.9 mmSmartSpin2k Panelized, the printed circuit board in 3D

    SmartSpin2k Panelized

    doudar/SmartSpin2k

    Transform your spin bike into a Smart Trainer!

    749 parts292GPL-2.0
  • 4 layers50 × 60 mmPiCCANTE OBD Dongle, the printed circuit board in 3D

    PiCCANTE OBD Dongle

    Alia5/PiCCANTE

    PiCCANTE is a powerful tool for exploring and reversing CAN busses of vehicles, based on Raspberry Pi Pico (any model)

    35 parts104GPL-3.0
  • 4 layers85.6 × 53.8 mmMuVox, the printed circuit board in 3D

    MuVox

    muvox-io/muVox

    Open Source Hardware Audio Amplifier

    128 parts84
  • 2 layers77 × 32 mmBananaSchplit, the printed circuit board in 3D

    BananaSchplit

    pms67/BananaSchplit

    Single rail DC (<12V) to split rail DC supply (+/-12V and +5V).

    53 parts66MIT
  • 4 layers56 × 60 mmPCBA KNOT, the printed circuit board in 3D

    PCBA KNOT

    intechstudio/knot

    Knot is the bridge between old-school MIDI gear like synthesizers, groove boxes, guitar pedals and neat USB MIDI devices.

    111 parts58GPL-3.0
  • 2 layers105.2 × 71.1 mmOnyx PCB, the printed circuit board in 3D

    Onyx PCB

    CuriousMotor/Onyx-Stepper-Motherboard

    The successor of the iconic Arduino-CNC-shield

    96 parts56MIT
  • 2 layers75.8 × 92.5 mmESP32 STEPPER CONTROL PCB, the printed circuit board in 3D

    ESP32 STEPPER CONTROL PCB

    JohnDecebal/UNDR

    UNDR AUTO is a fully automatic WDT (Weiss Distribution Technique) tool designed for espresso enthusiasts. This open-source DIY project combines 3D printed parts with electronic and mechanical components to create a…

    48 parts46
  • 2 layers96 × 74.4 mmMonolith, the printed circuit board in 3D

    Monolith

    luftaquila/monolith

    DIY wireless real-time datalogging platform for Student Formula and Baja.

    138 parts45

Parts like it

1

Questions

Is there a KiCad symbol and footprint for the TPS5430DDA?

Yes. The symbol is Regulator_Switching:TPS5430DDA and the footprint Package_SO:TI_SO-PowerPAD-8, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS5430DDA?

ESOP-8, with 9 pins. Its footprint is drawn on this page.

Where is the TPS5430DDA datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS5430DDA?

JLCPCB lists it as part C502477, with 3,502 in stock; the sellers' links on this page open their listings.

What can replace the TPS5430DDA?

Parts like it in the library: the TPS5430DDARG4 by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TPS5430DDA?

181 boards in 140 repositories on GitHub; the most starred are listed on this page, with their KiCad files.