

Hene controllerv3
WIP
- Size
- 100 × 91 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 114
- Nets
- 98
- Pads
- 392
- Tracks, vias
- 574, 586
- Pours
- 41
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 21 Apr 2026
- Updated
- 10 Sep 2026
Overview
Hene controllerv3 is an open-source printed circuit board by l1g4v, from the l1g4v/HeNe-PowerSupply repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 100 × 91 mm with 114 parts on 98 nets, routed with 574 tracks and 586 vias.
It is built around the CH224K, LT8645SEV#PBF and W25Q128JVSIQ, with the LM393, SS12 and IRFS4127PBF among its other parts. Its parts include 45 capacitors, 23 resistors, 10 ICs, 5 inductors and 4 diodes. It belongs with the RP2350 boards of this library.
Main components
7CH224K
ESSOP-10-150mil-1mm-40℃~+90℃ 100W 4V~30V 5V、9V、12V、15V、20V Overvoltage Protection、Thermal Protection PD 3.0 Power Receiver Controller ESSOP-10-150mil-1mm USB PD ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersLT8645SEV#PBF
LQFN-32-EP(4x6)-40℃~+125℃ 1 2.5uA 200kHz~2.2MHz 3.4V~65V 8A Adjustable Buck Buck Built-in Yes LQFN-32-EP(4x6) DC-DC Converters ROHSAnalog DevicesDC-DC ConvertersW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHLM393
SOP-8-16V~16V 0℃~+70℃ 2 2.5mA 250nA 2V~36V 36V 5mV 5nA Fail-safe function Open-drain SOP-8 Comparators ROHSMSKSEMIComparatorsSS12
SMA(DO-214AC)Schottky DiodeshongjiachengIRFS4127PBF
D2PAK-55℃~+175℃ 1 N-channel 150nC@10V 200V 22mΩ@10V 375W 5.38nF 5V 72A 86pF D2PAK MOSFETs ROHSInfineon TechnologiesMOSFETsABM8-272-T3
SMD3225-4P-40℃~+85℃ 10pF 12MHz 50Ω SMD crystal oscillator ±30ppm ±30ppm SMD3225-4P Crystals ROHSAbraconCrystals
Parts
114| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 100n | Capacitor_SMD:C_0805_2012Metric | C9, C26, C29, C30, C31, C32, C33, C34, C36, C37, C40, C41, C42, C44, C45 |
| 10 | 100n | Capacitor_SMD:C_0402_1005Metric | C5, C10, C13, C14, C15, C16, C17, C18, C19, C20 |
| 9 | TestPoint | TestPoint:TestPoint_Pad_D1.5mm | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9 |
| 6 | 10k | Resistor_SMD:R_1206_3216Metric | R15, R16, R17, R18, R19, R25 |
| 4 | 4.7u | Capacitor_SMD:C_0402_1005Metric | C7, C8, C11, C12 |
| 4 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5 | H1, H2, H3, H4 |
| 4 | SS12 | Diode_SMD:D_SMA | D2, D3, D4, D5 |
| 3 | 10u | Capacitor_SMD:C_0805_2012Metric | C4, C6, C23 |
| 3 | 1k | Resistor_SMD:R_0402_1005Metric | R4, R5, R7 |
| 3 | 220u | Capacitor_SMD:CP_Elec_6.3x7.7 | C25, C28, C38 |
| 3 | 47u | Inductor_THT:L_Toroid_Vertical_L25.4mm_W14.7mm_P12.20mm_Vishay_TJ5 | L2, L3, L4 |
| 2 | 100n | Capacitor_SMD:C_1206_3216Metric | C35, C39 |
| 2 | 15p | Capacitor_SMD:C_0402_1005Metric | C2, C3 |
| 2 | 1u | Capacitor_SMD:C_0805_2012Metric | C1, C27 |
| 2 | 22 | Resistor_SMD:R_1206_3216Metric | R1, R3 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R8, R9 |
| 2 | 5k | Potentiometer_THT:Potentiometer_Bourns_3266Y_Vertical | RV1, RV2 |
| 2 | INA180A1 | Package_TO_SOT_SMD:SOT-23-5 | U7, U10 |
| 2 | IRFS4127 | Package_TO_SOT_SMD:TO-263-2 | Q1, Q2 |
| 2 | LOGO | LOGO | G***, G*** |
| 2 | SW_Push | Resistor_SMD:R_0805_2012Metric | SW1, SW2 |
| 1 | 0 | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 100k | Resistor_SMD:R_1206_3216Metric | R14 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric | R11 |
| 1 | 10n | Capacitor_SMD:C_0805_2012Metric | C43 |
| 1 | 10u | Capacitor_SMD:C_1206_3216Metric | C21 |
| 1 | 110k | Resistor_SMD:R_1206_3216Metric | R20 |
| 1 | 15p | Capacitor_SMD:C_0805_2012Metric | C24 |
| 1 | 1M | Resistor_SMD:R_1206_3216Metric | R21 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric | R10 |
| 1 | 1u | Capacitor_THT:C_Rect_L33.0mm_W15.0mm_P27.50mm_MKS4 | C22 |
| 1 | 221k | Resistor_SMD:R_1206_3216Metric | R23 |
| 1 | 3.3u | EasyEDA:L_pol_2016 | L1 |
| 1 | 30m | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R24 |
| 1 | 33 | Resistor_SMD:R_0402_1005Metric | R6 |
| 1 | 66.5k | Resistor_SMD:R_1206_3216Metric | R22 |
| 1 | ABM8-272-T3 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | CH224K | Package_SO:SSOP-10-1EP_3.9x4.9mm_P1mm_EP2.1x3.3mm | U4 |
| 1 | CONN | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J1 |
| 1 | DM | Resistor_SMD:R_0805_2012Metric | JP1 |
| 1 | DP | Resistor_SMD:R_0805_2012Metric | JP2 |
| 1 | LM393 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U8 |
| 1 | LT8645SEV#PBF | EasyEDA:LQFN-32_L6.0-W4.0-P0.40-BL-EP_LT8645SEV-PBF | U9 |
| 1 | NCP1117-3.3_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | OPA336Nx | Package_TO_SOT_SMD:SOT-23-5 | U5 |
| 1 | RP2350_60QFN | Package_DFN_QFN:QFN-60-1EP_7x7mm_P0.4mm_EP3.4x3.4mm_ThermalVias | U3 |
| 1 | SENSE | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | T | Connector_Wire:SolderWire-4sqmm_1x02_P12mm_D3mm_OD6mm | L5 |
| 1 | UCC27624DR | EasyEDA:SOIC-8_L4.9-W3.9-P1.27-LS5.9-BL | U6 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J4 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U2 |
More from l1g4v/HeNe-PowerSupply
4- 4 layers100 × 100 mm

- 4 layers100 × 100 mm

- 2 layers132 × 69 mm

- 2 layers84 × 32 mm

Similar boards
- 2 layers37.8 × 24.4 mm

Esp01-ws2812b breakout
MrAJB/ESP01-WS2812B
Development of a small ESP01 breakout board to support controlling two WS2812B LED strips and a Dallas DS18B20 temperature sensor, used for integration with HomeAssistant through ESPHome.
20 parts6MIT - 4 layers56 × 88 mm

Pico peltier
syauqi-alias/pico-peltier
A TEC Controller using Pico RP2350 with Analog Devices LT8722 full bridge driver rated at 15V 4A
99 parts1MIT - 4 layers140 × 54 mm

Picoclock
locked/picoclock
This repo is an attempt at building a Pico based alarm clock. It was created for my kids and features:
146 parts - 4 layers72.5 × 39.7 mm

FOC RP2350
totaldesaster/SimpleFOC-Serial-Driver
Advanced dual BLDC driver based on the RP2350 and DRV8323S ICs, designed to be controlled from a trajectory controller over RS-485, RS-422 or TTL UART. Features a compact high power design with two stacked PCBs.
68 parts1GPL-3.0 - 11 layers178.5 × 91.2 mm

- 4 layers170.2 × 170.2 mm

Nvme Carrier all M2
El-Luhb/nvme-Carrier-for-LattePanda-Mu
nvme Carrier PCB for the LattePanda Mu compute module
400 parts12MIT - 4 layers65 × 65 mm

PAMI 2027 A1
Les-opossums/ELE_PAMI_2027
This repository contains the hardware design files for the PAMI2027A1 PCB (Rev A1), designed using KiCad 10.
249 parts - 2 layers76 × 90 mm

Questions
How big is the Hene controllerv3 PCB?
It measures 100 × 91 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Hene controllerv3 use?
114 parts, built around the CH224K, LT8645SEV#PBF, W25Q128JVSIQ and LM393. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Hene controllerv3 KiCad files?
From the l1g4v/HeNe-PowerSupply repository on GitHub, at the commit this page was made from: the board is hene_controllerv3/hene_controllerv3.kicad_pcb and its schematic hene_HV/hene_HV.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Hene controllerv3 design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).