Skip to the content
2 layers37.8 × 24.4 mmEsp01-ws2812b breakout, the printed circuit board in 3D

Esp01-ws2812b breakout

MrAJB/ESP01-WS2812B6

Development of a small ESP01 breakout board to support controlling two WS2812B LED strips and a Dallas DS18B20 temperature sensor, used for integration with HomeAssistant through ESPHome.

Size
37.8 × 24.4 mm
Copper layers
2
Thickness
1.6 mm
Parts
20
Nets
9
Pads
48
Tracks, vias
143, 12
Pours
1
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
20 Dec 2020
Updated
10 Dec 2021

Overview

Esp01-ws2812b breakout is an open-source printed circuit board by MrAJB, from the MrAJB/ESP01-WS2812B repository on GitHub, published under the MIT licence. It is a 2-layer board of 37.8 × 24.4 mm with 20 parts on 9 nets, routed with 143 tracks and 12 vias.

It is built around the DS18B20, LM1117-3.3 and IRFS4127PBF. Its parts include 5 resistors, 4 capacitors, 3 ICs, 3 connectors and 1 transistor. It belongs with the interfaces and adapters and home automation and IoT boards and the ESP8266 boards of this library.

Main components

3

README

README.md

Introduction

This repo documents the development of a small ESP-01 breakout board to support controlling two WS2812B LED strips and a Dallas DS18B20 temperature sensor. This allows for easy integration with HomeAssistant through ESPHome.

Note that I'm just developing this stuff in my spare time and I'm far from an expert. Development may be slow and I cannot make any promises on the quality of this board. However, feel free to look around, maybe there's something useful for you in there!

Hardware Overview

A schematic overview of the breakout board can be found here. As an be seen, this simple board allows to fit an ESP-01. Furthermore, it contains two level-shifters to control 5V data lines. The board is prepared to mount a DS18B20 temperature sensor, if desired. Lastly, a header to interface with the GPIO0 pin can be added, to further expand this board.

The layout and routing of V1 are finished: pcb_front (Note: the cutout in the lower left section aims to provide clearance for the WiFi antenna to improve the ESP's WiFi range.)

pcb_rear

Parts

20
QtyValueFootprintReferences
310KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1, R2, R5
210uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC2, C3
2MountingHoleMountingHole:MountingHole_2.2mm_M2H1, H2
1
1100uFCapacitor_THT:CP_Radial_D5.0mm_P2.00mmC1
115ACustom Fuses:1808_SMD_Fuse_HolderF1
11uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC4
1470Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR3
14K7Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR6
1Conn_01x03_MaleConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ3
1DS18B20Package_TO_SOT_THT:TO-92_InlineU3
1ESP-01v090ESP8266:ESP-01U2
1IRFS4127Custom Mosfets:SOT-23_DS-REVERSEDQ1
1LM1117-3.3Package_TO_SOT_SMD:SOT-223U1
1Screw_Terminal_01x02Custom Terminals:0102-blue-terminalJ1
1Screw_Terminal_01x03custom_terminals:0103-blue-terminalJ2

Similar boards

  • 2 layers33.7 × 97.8 mmHAN ESP TSS721, the printed circuit board in 3D

    HAN ESP TSS721

    UtilitechAS/amsreader-firmware

    ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported

    29 parts470
  • 2 layers107.9 × 76.7 mmHydroponic, the printed circuit board in 3D

    Hydroponic

    Khanhdtr/hydroponis-hw-kicad

    101 parts
  • 2 layers121 × 68 mmFreeds sanchez, the printed circuit board in 3D

    Freeds sanchez

    pablozg/freeds

    Derivador de energía solar excedente creado por Pablo Zerón, Diseño PCB por Amcalo, Tester original por Aeizoon, Wiki por Zoilo Mora

    42 parts108
  • 2 layers80 × 54.9 mmESP32WifiAisTempVolt2, the printed circuit board in 3D

    ESP32WifiAisTempVolt2

    AK-Homberger/NMEA2000WifiGateway-with-ESP32

    This repository shows how to build a NMEA2000 WiFi Gateway with voltage and temperature alarms.

    18 parts94GPL-3.0
  • 2 layers52 × 61 mmArduino motorfocus, the printed circuit board in 3D

    Arduino motorfocus

    fehlfarbe/arduino-motorfocus

    Arduino motorfocus with moonlite protocol for telescopes

    23 parts58MIT
  • 2 layers69 × 57 mmBuoy4, the printed circuit board in 3D

    Buoy4

    wjpavalko/Maker-Buoy

    Repository of Open Source Maker Buoy Files

    46 parts39
  • 2 layers26 × 34.8 mmWemosD1Mini, the printed circuit board in 3D

    WemosD1Mini

    RuiSantosdotme/ESP8266-Multisensor-Shield

    Complete step-by-step instructions »

    10 parts29

Questions

How big is the Esp01-ws2812b breakout PCB?

It measures 37.8 × 24.4 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Esp01-ws2812b breakout use?

20 parts, built around the DS18B20, LM1117-3.3 and IRFS4127PBF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Esp01-ws2812b breakout KiCad files?

From the MrAJB/ESP01-WS2812B repository on GitHub, at the commit this page was made from: the board is Hardware/esp01-ws2812b-breakout.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Esp01-ws2812b breakout design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).