

ControllerV4
K-Scale Motor Controller
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 161
- Nets
- 151
- Pads
- 597
- Tracks, vias
- 1,354, 266
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 18 Jun 2024
- Updated
- 30 Aug 2024
Overview
ControllerV4 is an open-source printed circuit board by kscalelabs, from the kscalelabs/motor-controller repository on GitHub. It is a 4-layer board with 161 parts on 151 nets, routed with 1,354 tracks and 266 vias.
It is built around the ISO1050DUB, TPSM365R6FRDNR and B0505XT-1WR3-TR, with the AS5047P-ATSM, LAN8720A-CP and LDL1117S33R among its other parts. Its parts include 65 capacitors, 47 resistors, 12 transistors, 9 connectors and 8 ICs. It belongs with the robots and motor control boards and the STM32 boards of this library.
Main components
11ISO1050DUB
SOP-8-2.54mm-55℃~+105℃ 1 1Mbps 2500 3V~5.5V 4.75V~5.25V 50kV/us Bus fault detection and protection、Fail-safe SOP-8-2.54mm Isolated CAN Transceivers ROHSTexas InstrumentsIsolated CAN TransceiversTPSM365R6FRDNR
QFN-11(3.5x4.5)-40℃~+125℃ 1 1V~13V 2mm 3.5mm 3.6V~65V 4.5mm 4uA 600mA 82.7% Buck Overheat protection、Over Current Protection ±1% QFN-11(3.5x4.5) DC-DC Power Modules ROHSTexas InstrumentsDC-DC Power ModulesB0505XT-1WR3-TR
SMD,13.5x8.5mm1 1.5kV、1.5kV 1W 200mA 220kHz 3000uF 4.5V~5.5V 5V 85% Short Circuit Protection SMD,13.5x8.5mm Isolated Power Modules ROHSYLPTECIsolated Power ModulesAS5047P-ATSM
TSSOP-14_4.4x5.0x0.65P-40℃~+125℃ 0°~360° 1.2mm 15mA 4.4mm 4.5V~5.5V 5mm Magnetic rotary position sensor No SPI TSSOP-14 Position Sensors ROHSAdvanced Monolithic SystemsPosition SensorsLAN8720A-CP
QFN-24-EP(4x4)Ethernet ICsMicrochip TechnologyLDL1117S33R
SOT-223-4-40℃~+125℃@(Tj) 1 1.2A 18V 3.3V 500uA 600mV@(1.2A) 60uVrms 87dB@(120Hz) Fixed Over Current Protection、Thermal Shutdown Positive SOT-223-4 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLP5907MFX-3.3/NOPB(MS)
SOT-23-5-40℃~+125℃@(Tj) 1 180mV@(300mA) 2uA 3.3V 300mA 5.5V Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMSKSEMIVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsABM3B-8.000MHZ-10-1-U-T
SMD5032-4P-10℃~+60℃ 10pF 200Ω 8MHz ±10ppm ±10ppm SMD5032-4P Crystals ROHSAbraconCrystalsH1102NLT
SMD,12.7x7.1mm0℃~+70℃ 1.5kV 10/100 Base-T 1:1、1:1 Single port SMD,12.7x7.1mm Pulse Transformers(LAN) ROHSPULSEPulse Transformers(LAN)LTST-C190KGKT
0603-30℃~+85℃ 130° 20mA 2V 35mcd 567.5nm~576.5nm 574nm 75mW Discrete Diode Water Clear Yellow Green 0603 LED Indication - Discrete ROHSLite-OnLED Indication - DiscreteTYPE-C-31-M-12
SMD-30℃~+80℃ 1 10,000 cycles 16P 20V 5A 7.35mm Female Surface Mount, Right Angle Type-C SMD USB Connectors ROHSHRO ElectronicsUSB Connectors
README
README.mdK-Scale Motor Controller
archive/
Old motor driver designs
pcb/
New designs, focused on EtherCAT compatibility
No documentation yet (oops) but will show up soonTM once I can get some of the motor functions validated
Parts
161| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 470uF | Capacitor_SMD:C_2220_5750Metric | C3, C4, C8, C10, C14, C17, C19, C21, C59, C60, C63, C64, C65, C67 |
| 12 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C6, C11, C16, C18, C20, C22, C48, C49, C50, C51, C52, C53 |
| 12 | ~ | Package_SO:ONSemi_SO-8FL_488AA | Q5, Q6, Q7, Q8, Q9, Q10, Q11, Q12, Q13, Q14, Q15, Q16 |
| 7 | 2.2µF | Capacitor_SMD:C_0603_1608Metric | C7, C12, C13, C30, C40, C44, C46 |
| 7 | 22R | Resistor_SMD:R_0402_1005Metric | R39, R40, R42, R43, R44, R45, R46 |
| 6 | 2.2R | Resistor_SMD:R_0603_1608Metric | R31, R32, R33, R34, R36, R37 |
| 6 | 4.7uF | Capacitor_SMD:C_0805_2012Metric | C26, C27, C28, C47, C54, C57 |
| 4 | 2200pF | Capacitor_SMD:C_0603_1608Metric | C39, C41, C55, C56 |
| 4 | 22R | Resistor_SMD:R_0603_1608Metric | R2, R3, R24, R25 |
| 4 | 3.3k | Resistor_SMD:R_0603_1608Metric | R14, R15, R16, R23 |
| 4 | 49R9 | Resistor_SMD:R_0402_1005Metric | R19, R20, R21, R41 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 4 | TESTPOINT | TestPoint:TestPoint_Pad_1.0x1.0mm | TP1, TP2, TP4, TP5 |
| 3 | 120R | Resistor_SMD:R_0603_1608Metric | R6, R29, R30 |
| 3 | 22nF | Capacitor_SMD:C_0402_1005Metric | C31, C32, C33 |
| 2 | 10k | Resistor_SMD:R_0603_1608Metric | R4, R10 |
| 2 | 10pF | Capacitor_SMD:C_0603_1608Metric | C5, C9 |
| 2 | 120uF | Capacitor_SMD:CP_Elec_10x10.5 | C25, C34 |
| 2 | 18k | Resistor_SMD:R_0603_1608Metric | R22, R26 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric | R11, R13 |
| 2 | 270R | Resistor_SMD:R_0402_1005Metric | R18, R47 |
| 2 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C23, C24 |
| 2 | 47K | Resistor_SMD:R_0603_1608Metric | R8, R27 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R1, R7 |
| 2 | 500uOhm | Resistor_SMD:R_2512_6332Metric | R35, R38 |
| 2 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5, J9 |
| 2 | Conn_01x05_Socket | Hole-Mounts:Five-Hole | J3, J8 |
| 2 | LED | Diode_SMD:D_0603_1608Metric | D2, D4 |
| 1 | 0.022µF | Capacitor_SMD:C_0603_1608Metric | C42 |
| 1 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C37 |
| 1 | 100nF | Capacitor_SMD:C_0402_1005Metric | C71 |
| 1 | 10R | Inductor_SMD:L_0402_1005Metric | FB1 |
| 1 | 10uF | Capacitor_SMD:C_0402_1005Metric | C29 |
| 1 | 11.3k | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 12.1K | Resistor_SMD:R_0402_1005Metric | R17 |
| 1 | 18K | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | 1nF (3KV) | Capacitor_SMD:C_1206_3216Metric | C38 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 1uF | Capacitor_SMD:C_0402_1005Metric | C35 |
| 1 | 2.2uF | Capacitor_SMD:C_1210_3225Metric | C1 |
| 1 | 220k | Resistor_SMD:R_0603_1608Metric | R28 |
| 1 | 22uH | Inductor_SMD:L_Taiyo-Yuden_NR-60xx | L2 |
| 1 | 22uf | Capacitor_SMD:C_2225_5664Metric | C15 |
| 1 | 25 MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y2 |
| 1 | 270pF | Capacitor_SMD:C_0603_1608Metric | C45 |
| 1 | 40.2k | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 470pF | Capacitor_SMD:C_0402_1005Metric | C36 |
| 1 | 6.8uH | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | 68uF | Capacitor_Tantalum_SMD:CP_EIA-6032-28_Kemet-C | C58 |
| 1 | 82pF | Capacitor_SMD:C_0603_1608Metric | C43 |
| 1 | ABM3B-8.000MHZ-10-1-U-T | Crystal:Crystal_SMD_5032-4Pin_5.0x3.2mm | Y1 |
| 1 | AS5047P-ATSM | AMS:SOP65P640X120-14N | U9 |
| 1 | B0505XT-1WR3-TR | IsolatedPower:CONV_B0505XT-1WR3-TR | PS2 |
| 1 | Conn_01x04 | Connector_Molex:Molex_PicoBlade_53048-0410_1x04_P1.25mm_Horizontal | J6 |
| 1 | Conn_01x04_Socket | Hole-Mounts:Nine-Hole | J10 |
| 1 | D | Diode_SMD:D_SOD-123F | D3 |
| 1 | H1102NLT | Ethernet:XFMR_H1102NLT | T1 |
| 1 | ISO1050DUB | Package_SO:SOP-8_6.62x9.15mm_P2.54mm | U1 |
| 1 | LAN8720A | Package_DFN_QFN:VQFN-24-1EP_4x4mm_P0.5mm_EP2.5x2.5mm_ThermalVias | U6 |
| 1 | LDL1117S33R | Package_TO_SOT_SMD:SOT-223 | U4 |
| 1 | LOGO | Stompy:biggerstompy | G*** |
| 1 | LP5907MFX-3.3_NOPB | Package_TO_SOT_SMD:SOT-23-5 | U5 |
| 1 | LTST-C190KGKT | Diode_SMD:D_0603_1608Metric | D1 |
| 1 | STM32F405RGTx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U3 |
| 1 | Screw_Terminal_01x02 | Hole-Mounts:Two-Hole | J1 |
| 1 | Screw_Terminal_01x03 | Hole-Mounts:Three-Hole | J7 |
| 1 | TPSM365R6FRDNR | 5VPower:RDN0011A-MFG | U2 |
| 1 | TYPE-C-31-M-12 | USB-C:HRO_TYPE-C-31-M-12 | J2 |
| 1 | ~ | Package_SO:HTSSOP-56-1EP_6.1x14mm_P0.5mm_EP3.61x6.35mm | U8 |
More from kscalelabs/motor-controller
7- 4 layers127 × 67.3 mm

- 6 layers

- 6 layers

- 6 layers

- 4 layers

- 4 layers

- 2 layers47.7 × 38 mm

Similar boards
- 4 layers100 × 80 mm

Mouse joystick pcb
peterpolidoro/mouse-joystick-pcb
KiCad design, fabrication package and documentation for a single-axis mouse joystick controller board: RP2040, TMC5130A stepper driver, brake and torque front ends, a pyControl UART peripheral for the Janelia Dudman lab…
364 parts1 - 2 layers78.1 × 61 mm

- 4 layers236.1 × 156.9 mm

- 2 layers138.8 × 55 mm

MuxPi
SamsungSLAV/muxpi
MuxPi is an open hardware and open software board which was designed to aid in automating tasks on physical devices.
354 parts22Apache-2.0 - 4 layers394 × 110 mm

Gpu cluster backplane
antmicro/gpu-cluster-backplane
This project contains open hardware design files for a PCB supporting power distribution in a cluster composed of GPUs. This board has been derived from an open source d1600e-psu-breakout created by Antmicro.
616 parts4Apache-2.0 - 4 layers90 × 90 mm

FlightComputer
jbrown3859/EE175-SeniorDesign
CubeSat Flight Computer and Radio - EE175 Senior Design F22
83 parts3 - 4 layers70 × 35 mm

- 2 layers104 × 129 mm

Questions
What parts does the ControllerV4 use?
161 parts, built around the ISO1050DUB, TPSM365R6FRDNR, B0505XT-1WR3-TR and AS5047P-ATSM. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ControllerV4 KiCad files?
From the kscalelabs/motor-controller repository on GitHub, at the commit this page was made from: the board is archive/ControllerV4/ControllerV4.kicad_pcb and its schematic archive/ControllerV1/ControllerTop.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ControllerV4 design in my own project?
Its repository states no licence, so its author keeps all rights: ask kscalelabs before reusing the design.