
Sangaboard v0.3
kitspace-test-repos/Sangaboard
The Sangaboard is a motor controller for unipolar stepper motors such as the cheap 28BYJ-48 motors. The custom board (v0.3) can be programmed as an Arduino Leonardo in the Arduino IDE.

The Sangaboard is a motor controller for unipolar stepper motors such as the cheap 28BYJ-48 motors. The custom board (v0.3) can be programmed as an Arduino Leonardo in the Arduino IDE.
Sangaboard v0.4 is an open-source printed circuit board by kitspace-test-repos, from the kitspace-test-repos/Sangaboard repository on GitHub. It is a 2-layer board of 65 × 56.5 mm with 96 parts on 96 nets, routed with 1,321 tracks and 95 vias.
It is built around the ATMEGA32U4-MU, ULN2003A and CAT24C32LI-, with the DMG2305UX and DMMT5401 among its other parts. Its parts include 22 resistors, 15 capacitors, 15 connectors, 8 transistors and 5 ICs. It belongs with the robots and motor control boards and the AVR (ATmega, ATtiny) boards of this library.
The Sangaboard is a motor controller for unipolar stepper motors such as the cheap 28BYJ-48 motors. The custom board (v0.3) can be programmed as an Arduino Leonardo in the Arduino IDE. Versions 0.1 and 0.2 were based on an Arduino Nano and a couple of Darlington pair ICs. It owes quite a bit to Fergus Riche's motor board, the hardware developed by OpenScope and the Arduino-based motor controller used by a number of summer students working with Richard Bowman in Cambridge, particularly James Sharkey. It is currently the motor board used by the OpenFlexure Microscope. It was formerly known as the OpenFlexure Nano Motor Controller, with a repository on github.
The first step is to make and populate the PCB. You can get in touch with STICLab to order a v0.3 one if they have stock, eventually this should be possible through Seeed Studio. Alternatively have version 0.2 or version 0.3 made via Kitspace.
You only need to isntall a bootloader if you solder your own v0.3 or v0.4 Sangaboard! Otherwise you can skip this step.
The Sangaboard firmware is an Arduino sketch, we use the same sketch for all versions of the Sangaboard.
The stage can be controlled by serial commands, which can be listed by sending the query help? to the board over the serial port.
Or by the pySangaboard python library.
Development of this board and software was funded by the EPSRC (EP/P029426/1), the Royal Commission for the Exhibition of 1851, and the University of Bath.
(c) The authors, 2017,2018,2019. Released under CERN Open Hardware License (hardware designs) and GNU GPL v3.0 (firmware). The bootloader is only very slightly modified from the Arduino Leonardo bootloader, licences are listed in the source.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 22 | Resistor_SMD:R_0805_2012Metric | R3, R4, R6, R7, R9, R10, R11, R12, R13, R16 |
| 4 | 10uF | Capacitor_SMD:C_0805_2012Metric | C4, C5, C11, C12 |
| 4 | 1K | Resistor_SMD:R_0805_2012Metric | R14, R15, R17, R18 |
| 4 | 1uF | Capacitor_SMD:C_0805_2012Metric | C8, C9, C14, C15 |
| 4 | 3mm_Mounting_Hole | project_footprints:NPTH_3mm_ID | H1, H2, H3, H4 |
| 4 | DMG2305UX | Package_TO_SOT_SMD:SOT-23 | Q3, Q4, Q6, Q8 |
| 4 | DMMT5401 | Package_TO_SOT_SMD:SOT-23-6 | Q1, Q2, Q5, Q7 |
| 4 | Jumper_NC | Jumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mm | JP1, JP2, JP3, JP4 |
| 3 | 0A35_0A7_Polyfuse | Resistor_SMD:R_1206_3216Metric | F3, F4, F5 |
| 3 | 100n | Capacitor_SMD:C_0805_2012Metric | C6, C7, C10 |
| 3 | 10K | Resistor_SMD:R_0805_2012Metric | R5, R8, R20 |
| 3 | TestPoint | TestPoint:TestPoint_Pad_2.0x2.0mm | TP1, TP2, TP3 |
| 2 | 1.5K | Resistor_SMD:R_0805_2012Metric | R1, R2 |
| 2 | 22pF | Capacitor_SMD:C_0805_2012Metric | C2, C3 |
| 2 | 3.9K | Resistor_SMD:R_0805_2012Metric | R21, R22 |
| 2 | Ferrite_Bead | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | L1, L2 |
| 2 | ULN2003A | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U3, U4 |
| 2 | Varistor | Resistor_SMD:R_0603_1608Metric | RV1, RV2 |
| 1 | sangaboard_Logo:sangaboard_L5_FS | ||
| 1 | Symbols:OSHW-Logo_5.7x6mm_SilkScreen | ||
| 1 | sangaboard_Logo:sangaboard_L3_FS | ||
| 1 | Symbols:OSHW-Logo_19x20mm_SilkScreen | ||
| 1 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 0A5_1A_Polyfuse | Resistor_SMD:R_1206_3216Metric | F1 |
| 1 | 100nf | Capacitor_SMD:C_0805_2012Metric | C13 |
| 1 | 1A25_3A_Polyfuse | Resistor_SMD:R_1210_3225Metric | F2 |
| 1 | 8MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | ATmega32U4-MU | Package_QFP:TQFP-44-1EP_10x10mm_P0.8mm_EP4.5x4.5mm | U1 |
| 1 | BLUE_MTR | LED_SMD:LED_0805_2012Metric | D3 |
| 1 | CAT24C32 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | CD1206-SO1575 | Diode_SMD:D_SOD-123F | D1 |
| 1 | CONN_01X02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J13 |
| 1 | DNP | Resistor_SMD:R_0805_2012Metric | R19 |
| 1 | EEPROM-raspberrypi_hat | project_footprints:EEPROM-raspberrypi_hat | J15 |
| 1 | END_STOPS | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J3 |
| 1 | GREEN | LED_SMD:LED_0805_2012Metric | D4 |
| 1 | I/O | Connector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_Vertical | J9 |
| 1 | I2C Header | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J4 |
| 1 | ISP | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J6 |
| 1 | J_AUX | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J7 |
| 1 | MCP1700-3302E_SOT23 | Package_TO_SOT_SMD:SOT-23 | U2 |
| 1 | Power&Serial-raspberrypi_hat | Connector_PinSocket_2.54mm:PinSocket_2x05_P2.54mm_Vertical | J14 |
| 1 | RED_3V3 | LED_SMD:LED_0805_2012Metric | D2 |
| 1 | Reset | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | RST1 |
| 1 | Serial Header | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J5 |
| 1 | ULN_AUX | Connector_PinSocket_2.54mm:PinSocket_2x04_P2.54mm_Vertical | J8 |
| 1 | USB_Data | Connector_USB:USB_Micro-B_Molex-105017-0001 | J1 |
| 1 | USB_Supply | Connector_USB:USB_Micro-B_Molex-105017-0001 | J2 |
| 1 | X_AXIS | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J10 |
| 1 | YELLOW | LED_SMD:LED_0805_2012Metric | D5 |
| 1 | Y_AXIS | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J11 |
| 1 | Z_AXIS | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J12 |

kitspace-test-repos/Sangaboard
The Sangaboard is a motor controller for unipolar stepper motors such as the cheap 28BYJ-48 motors. The custom board (v0.3) can be programmed as an Arduino Leonardo in the Arduino IDE.

SkullKill/ACYONP-PCB
PCB for Access Control Yubikey OTP NFC Pi (ACYONP). For Raspberry Pi. This is a Door Access Control using Electronic Door Strike, with Yubikey OTP via NFC / KeyPad / WebInterface for Authentication.

hasenbanck/heteromycin
A 3D printer board using a powerfull STM32 MCU, TMC5160/TMC2160 driver and a Raspberry Pi or compatible SBC




pilotniq/MJoulnir
Hardware and software for the control system of a full size electric boat.


It measures 65 × 56.5 mm and has 2 copper layers, 1.6 mm thick.
96 parts, built around the ATMEGA32U4-MU, ULN2003A, CAT24C32LI- and DMG2305UX. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the kitspace-test-repos/Sangaboard repository on GitHub, at the commit this page was made from: the board is pcb_design/v0.4/sangaboard_v0.4.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask kitspace-test-repos before reusing the design.