Skip to the content
2 layers66.5 × 37.5 mmDC Motor Speed Controller-, the printed circuit board in 3D

A 555 timer–based DC motor speed controller designed to control the speed of a DC motor using PWM (Pulse Width Modulation).

Size
66.5 × 37.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
19
Nets
11
Pads
42
Tracks, vias
76, 0
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
13 Aug 2026
Updated
19 Aug 2026

Overview

DC Motor Speed Controller- is an open-source printed circuit board by KhushiShah63, from the KhushiShah63/DC-Motor-Speed-Controller- repository on GitHub. It is a 2-layer board of 66.5 × 37.5 mm with 19 parts on 11 nets, routed with 76 tracks and 0 vias.

It is built around the NA555P and TIP122. Its parts include 4 diodes, 3 capacitors, 3 resistors, 2 connectors and 1 IC. It belongs with the robots and motor control boards of this library.

Main components

2

README

README.md

DC Motor Speed Controller

A 555 timer–based DC motor speed controller designed to control the speed of a DC motor using PWM (Pulse Width Modulation).

The circuit uses an NE555 timer to generate the PWM signal, a potentiometer to adjust the duty cycle, and a TIP122 Darlington transistor to drive the DC motor. A 1N4007 diode is used for protection against the motor's back EMF.


📌 Project Overview

This project demonstrates the design of a simple and adjustable DC motor speed controller using analog electronic components.

The NE555 timer is configured to generate a PWM signal. By adjusting the potentiometer, the PWM duty cycle changes, which controls the amount of power delivered to the motor and therefore changes its speed.

The TIP122 transistor acts as the switching device between the control circuit and the DC motor.


⚙️ Key Features

  • Adjustable DC motor speed control
  • NE555-based PWM generation
  • Potentiometer-based speed adjustment
  • TIP122 transistor for motor switching
  • 1N4007 diode for motor protection
  • LED power/status indication
  • Compact circuit suitable for PCB implementation
  • Designed using KiCad

🧩 Components Used

ComponentValue / Part
Timer ICNE555 / NA555P
Power TransistorTIP122
PotentiometerRV1
ResistorR1 – 2.2kΩ
ResistorR2 – Value as shown in schematic
ResistorR3 – 1kΩ
CapacitorC1 – 1000µF
CapacitorC2 – 100nF
CapacitorC3 – 100nF
DiodeD2 – 1N4007
DiodeD3 – 1N4007
DiodeD4 – 1N4007
LEDD1
MotorDC Motor
Connectors2-pin Screw Terminals

🔌 Circuit / Schematic

image

🖥️ PCB Design

The schematic was used as the basis for PCB design, including component placement and PCB routing.

image

3-D View

image

🔌 Circuit Connections

The major sections of the circuit are:

1. PWM Generation

The NE555 timer is configured as the PWM generation stage.

The potentiometer (RV1) is used to adjust the timing characteristics of the 555 timer, changing the PWM duty cycle.

2. Motor Driver

The PWM output from the NE555 is connected through R3 (1kΩ) to the base of the TIP122 transistor.

The TIP122 acts as the switching element that controls the current supplied to the DC motor.

3. Motor Protection

A 1N4007 diode (D4) is connected across the motor terminals.

It provides protection against voltage spikes generated by the motor when the switching transistor turns OFF.

4. Filtering and Timing

The capacitors are used for timing and supply filtering:

  • C1 – 1000µF supply filtering
  • C2 – 100nF timing/filtering capacitor
  • C3 – 100nF timing/filtering capacitor

5. LED Indication

D1 is used as an LED indicator in the circuit to provide visual indication of the powered/control section.


🎛️ Speed Control Principle

The motor speed is controlled by changing the PWM duty cycle.

text
Potentiometer
      ↓
NE555 Timer
      ↓
PWM Signal
      ↓
TIP122 Transistor
      ↓
DC Motor
      ↓
Motor Speed

---

🏗️ System Block Diagram
                 ┌───────────────────┐
                 │   DC Power Input  │
                 └─────────┬─────────┘
                           │
                           ▼
                 ┌───────────────────┐
                 │     NE555 Timer   │
                 │   PWM Generation  │
                 └─────────┬─────────┘

Parts

19
QtyValueFootprintReferences
31N4007Diode_THT:D_DO-41_SOD81_P10.16mm_HorizontalD2, D3, D4
21KResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_HorizontalR2, R3
2Screw_Terminal_01x02Terminal_bornier:TerminalBlock_bornier-2_P5.08mmJ1, J2
11000uFCapacitor_THT:C_Disc_D4.7mm_W2.5mm_P5.00mmC1
1100nFCapacitor_THT:C_Disc_D4.7mm_W2.5mm_P5.00mmC2
1100nFCapacitor_THT:C_Radial_D6.3mm_H7.0mm_P2.50mmC3
12.2KResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_HorizontalR1
1LEDLED_THT:LED_D5.0mmD1
1NA555PPackage_DIP:DIP-8_W7.62mmU1
1R_PotentiometerPotentiometer_THT:Potentiometer_Alps_RK163_Single_HorizontalRV1
1TIP122Package_TO_SOT_THT:TO-220-3_VerticalQ1

The 15 most common of 19 parts.

Similar boards

  • 2 layers55.9 × 64.8 mmMnet uart, the printed circuit board in 3D

    Mnet uart

    gajdi88/M-NET-Thermostat

    Smart thermostat for Mitsubishi's M-NET communication protocol

    33 parts2GPL-3.0
  • 2 layersEDiCPoster, the printed circuit board in 3D

    EDiCPoster

    Nik-Sch/EDiC

    Developement, Simulation and Emulation of an 8 bit CPU including a Software Framework for my Masters Thesis

    176 parts1
  • 2 layers110.7 × 74.7 mmTgn, the printed circuit board in 3D

    Tgn

    0x007E/tgn

    Tone generator

    92 parts
  • 2 layers127 × 62.5 mmAcClutchBoost, the printed circuit board in 3D

    AcClutchBoost

    bhavsarp23/acClutchBoost

    KiCad source files for AC Clutch Booster

    34 parts
  • 2 layers29 × 27.5 mmQueaky Stem Toy, the printed circuit board in 3D

    Queaky Stem Toy

    GokulS20G/queaky-stem-toy-pcb

    PCB design of a Queaky Stem Toy using KiCad with schematic, layout, and Gerber files.

    8 partsMIT
  • 2 layers120 × 80 mmPuente H, the printed circuit board in 3D

    Puente H

    jeremiasadrian/jeremiasadrian

    Config files for my GitHub profile.

    89 parts
  • 4 layers161.1 × 82.9 mmAll in one smc, the printed circuit board in 3D

    All in one smc

    nojan1/project-wrass

    The purpose of Project Wrass is to develop the Wrass 1.

    150 parts

Questions

How big is the DC Motor Speed Controller- PCB?

It measures 66.5 × 37.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the DC Motor Speed Controller- use?

19 parts, built around the NA555P and TIP122. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the DC Motor Speed Controller- KiCad files?

From the KhushiShah63/DC-Motor-Speed-Controller- repository on GitHub, at the commit this page was made from: the board is DC Motor speed controller.kicad_pcb and its schematic DC Motor speed controller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the DC Motor Speed Controller- design in my own project?

Its repository states no licence, so its author keeps all rights: ask KhushiShah63 before reusing the design.