
Mnet uart
gajdi88/M-NET-Thermostat
Smart thermostat for Mitsubishi's M-NET communication protocol

KiCad source files for AC Clutch Booster
AcClutchBoost is an open-source printed circuit board by bhavsarp23, from the bhavsarp23/acClutchBoost repository on GitHub. It is a 2-layer board of 127 × 62.5 mm with 34 parts on 17 nets, routed with 129 tracks and 0 vias.
It is built around the I7C2W020A120V-001-R, NA555P and TLE4274V50AKSA2, with the A21ASP12VDC1.6, A21CSP12VDC1.6 and VS-ETH3007-M3 among its other parts. Its parts include 11 capacitors, 4 resistors, 4 diodes, 3 ICs and 2 transistors.
acClutchBoost is a KiCad hardware project designed to improve AC clutch engagement on the 8th Generation Honda Civic Si. The project addresses a common issue where the AC clutch fails to engage reliably due to increased air gap from clutch wear, particularly at high ambient temperatures.
The repository includes the schematic, PCB layout, and BOM required to build the circuit.
Over time, wear in the AC clutch friction material increases the air gap between the clutch plate and pulley. As the gap grows, the clutch solenoid may no longer generate sufficient magnetic force to pull in the clutch, especially under adverse conditions such as high temperatures.
At elevated temperatures, clutch engagement can degrade further, potentially due to reduced magnetic permeability of the ferrous components or increased coil resistance. The result is intermittent or complete AC failure despite correct ECU commands.
When the vehicle ECU commands AC clutch engagement, acClutchBoost briefly increases the voltage supplied to the clutch coil above the nominal automotive range (approximately 12–14 V). This higher voltage is applied for a short, configurable duration to ensure reliable pull-in of the clutch. After this initial boost period, the circuit returns the clutch supply to normal voltage to avoid overheating or long-term stress.
This approach improves engagement reliability without permanent mechanical modification of the clutch assembly.
The circuit consists of:
Schematic
Complete circuit design showing power, control, and timing sections.
PCB Layout
Board layout suitable for automotive installation considerations.
BOM (Bill of Materials)
Component list with values and part references.
Boost Voltage
Set via trim potentiometer on the DC-DC converter.
Boost Duration
Controlled by the adjustable timing circuit to apply voltage only during initial engagement. Set via trim potentiometer.
Both parameters can be tuned to balance reliable clutch pull-in with long-term component safety.
This project is intended for:
It is not a replacement for proper mechanical repair, but a practical electrical mitigation for a known failure mode.
This project interfaces with automotive electrical systems. Improper installation or tuning may result in damage to vehicle components or injury. Use at your own risk.
This project is licensed under the CERN Open Hardware Licence v2 – Weakly Reciprocal (CERN-OHL-W v2).
You are free to use, modify, manufacture, and distribute this hardware design, provided that any modifications to the licensed material are released under the same license.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 0.1uF | Capacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C4, C6, C10, C11 |
| 2 | 100k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R6, R7 |
| 2 | 10uF | Capacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C3, C5 |
| 2 | 1N4002 | Diode_THT:D_DO-41_SOD81_P7.62mm_Horizontal | D1, D2 |
| 2 | 220uF | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C2, C8 |
| 2 | 2N7000 | Package_TO_SOT_THT:TO-92_Inline | Q1, Q2 |
| 2 | 33uF | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C7, C9 |
| 1 | 100 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R4 |
| 1 | 1000uF | Capacitor_THT:CP_Radial_D12.5mm_P5.00mm | C1 |
| 1 | 100k | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV1 |
| 1 | 10k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R5 |
| 1 | 1N5256B-TR | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D4 |
| 1 | 500k | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV2 |
| 1 | A21ASP12VDC1.6 | footprints:AutomotiveA2Relay_Form1A | K1 |
| 1 | A21CSP12VDC1.6 | footprints:AutomotiveA2Relay_Form1C | K2 |
| 1 | Conn_01x04 | Connector_Wire:SolderWire-2.5sqmm_1x04_P7.2mm_D2.4mm_OD3.6mm | J1 |
| 1 | I7C2W020A120V-001-R | footprints:CONV_I7C2W020A120V-001-R | U3 |
| 1 | NA555P | Package_DIP:DIP-8_W7.62mm | U2 |
| 1 | TLE4274V50AKSA2 | Package_TO_SOT_THT:TO-220-3_Vertical | U1 |
| 1 | VS-ETH3007-M3 | Package_TO_SOT_THT:TO-220-2_Vertical | D3 |
The 29 most common of 34 parts.

gajdi88/M-NET-Thermostat
Smart thermostat for Mitsubishi's M-NET communication protocol

KhushiShah63/DC-Motor-Speed-Controller-
A 555 timer–based DC motor speed controller designed to control the speed of a DC motor using PWM (Pulse Width Modulation).

Nik-Sch/EDiC
Developement, Simulation and Emulation of an 8 bit CPU including a Software Framework for my Masters Thesis



GokulS20G/queaky-stem-toy-pcb
PCB design of a Queaky Stem Toy using KiCad with schematic, layout, and Gerber files.


It measures 127 × 62.5 mm and has 2 copper layers, 1.6 mm thick.
34 parts, built around the I7C2W020A120V-001-R, NA555P, TLE4274V50AKSA2 and A21ASP12VDC1.6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the bhavsarp23/acClutchBoost repository on GitHub, at the commit this page was made from: the board is acClutchBoost.kicad_pcb and its schematic acClutchBoost.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask bhavsarp23 before reusing the design.