
Smart Energy meter
kaviyarasu-s-ece/Voltage-and-Current-Sensor
This circuit will detect the change in current voltage variation. It will send the analog signal to esp32 circuit which used for live monitoring

Smart Energy Meter
Smart Energy meter is an open-source printed circuit board by Karthickraja1807, from the Karthickraja1807/GRID-PULSE repository on GitHub. It is a 2-layer board of 115.9 × 45.4 mm with 55 parts on 68 nets, routed with 294 tracks and 40 vias.
It is built around the ESP32-WROOM-32E, LM358 and AMS1117-3.3, with the TYPE-C-31-M-12 and ZMPT101B among its other parts. Its parts include 18 resistors, 13 capacitors, 6 connectors, 4 ICs and 2 diodes. It belongs with the ESP32 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10k | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R3, R4, R5, R7, R9, R10 |
| 5 | TestPoint | Connector_PinHeader_2.00mm:PinHeader_1x01_P2.00mm_Vertical | 3V3_OP1, 5v_op1, c_op1, gnd_op1, v_op1 |
| 2 | 100nF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C9, C10 |
| 2 | 100ohm | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R17, R18 |
| 2 | 10K | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R13, R14 |
| 2 | 10uF | Diode_SMD:D_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C11, C12 |
| 2 | 1nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C6 |
| 2 | 1uf | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C2 |
| 2 | Conn_01x04 | Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | J3, J6 |
| 2 | LED | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1, D2 |
| 2 | SW_Push | Button_Switch_SMD:SW_SPST_B3U-1000P | SW1, SW2 |
| 1 | .1uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C5 |
| 1 | 100 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1 |
| 1 | 100k | Diode_SMD:D_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R8 |
| 1 | 100k | Fuse:Fuse_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R6 |
| 1 | 100nf | Capacitor_SMD:C_1206_3216Metric | C13 |
| 1 | 100pF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C7 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8 |
| 1 | 1K | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R12 |
| 1 | 1nf | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 1 | 2K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11 |
| 1 | 5.1K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15 |
| 1 | 5.1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R16 |
| 1 | 820k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2 |
| 1 | ACS712xLCTR-30A | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | AMS1117-3.3 | MyFootprints:SOT229P700X180-4N | U4 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_2.00mm:PinHeader_1x04_P2.00mm_Vertical | J1 |
| 1 | ESP32-WROOM-32E | MyFootprints:ESP32-WROOM-32E | U3 |
| 1 | Fuse | Fuse:Fuseholder_Clip-5x20mm_Littelfuse_111_Inline_P20.00x5.00mm_D1.05mm_Horizontal | F1 |
| 1 | LM358 | MyFootprints:SOIC127P599X175-8N | U1 |
| 1 | R_Potentiometer_Trim | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV1 |
| 1 | TYPE-C-31-M-12 | MyFootprints:HRO_TYPE-C-31-M-12 | J2 |
| 1 | ZMPT101B | MyFootprints:XFMR_ZMPT101B | T1 |
| 1 | ac input | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J4 |
| 1 | current_i/p | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J5 |
The 53 most common of 55 parts.

kaviyarasu-s-ece/Voltage-and-Current-Sensor
This circuit will detect the change in current voltage variation. It will send the analog signal to esp32 circuit which used for live monitoring

Arhamee/hardware-portfolio
Multi-layer PCB designs in KiCad 10 schematic capture to fabrication-ready Gerbers. High-speed routing, BGA escape, power electronics.




Samuelmathe/TFC-Multicanal-Goma
TFC ULPGL Goma - Systeme IoT multicanal de sous-comptage energetique (ESP32, KiCad, Flutter)


It measures 115.9 × 45.4 mm and has 2 copper layers, 1.6 mm thick.
55 parts, built around the ESP32-WROOM-32E, LM358, AMS1117-3.3 and TYPE-C-31-M-12. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Karthickraja1807/GRID-PULSE repository on GitHub, at the commit this page was made from: the board is circuit_of_smart_energy_meter/Smart_Energy_meter.kicad_pcb and its schematic circuit_of_smart_energy_meter/Smart_Energy_meter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Karthickraja1807 before reusing the design.