

- Size
- 90 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 144
- Nets
- 92
- Pads
- 367
- Tracks, vias
- 1,085, 93
- Pours
- 207
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 4 Jul 2025
- Updated
- 15 Jun 2026
Overview
Bd2wl is an open-source printed circuit board by kanengomibako, from the kanengomibako/EffectsPedals repository on GitHub, published under the Unlicense licence. It is a 2-layer board of 90 × 100 mm with 144 parts on 92 nets, routed with 1,085 tracks and 93 vias.
It is built around the STM32L010F4P6, TC7W66FK,LF and NCP718BSN330, with the 1SS387, 2SC4116-GR,LF and DTC143ZMFHAT2L among its other parts. Its parts include 50 resistors, 40 capacitors, 15 transistors, 12 diodes and 7 ICs. It belongs with the STM32 boards of this library.
Main components
8STM32L010F4P6
TSSOP-20-169mil-40℃~+85℃ 1.8V~3.6V 128Byte 12bit 16 16KB 2KB 32 Bit 32MHz ARM Cortex-M0+ Built-in FLASH TSSOP-20 Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)TC7W66FK,LF
VSSOP-8-0.5mm-40℃~+85℃ 1uA 2/2 2V~12V 7ns@5V,50pF Single Supply VSSOP-8-0.5mm Signal Switches, Multiplexers, Decoders ROHSToshibaSignal Switches, Multiplexers, DecodersNCP718BSN330
TSOT-23-5-40℃~+125℃@(Tj) 1 24V 295mV@(300mA) 3.3V 300mA 36uVrms 4uA 60dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive TSOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSonsemiVoltage Regulators - Linear, Low Drop Out (LDO) Regulators1SS387
SOD-5231.2V@100mA 100mA 150mW 2A 4ns 500nA@80V 80V Independent SOD-523 Switching Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Switching Diodes2SC4116-GR,LF
SOT-323(SC-70)-55℃~+125℃ 1 NPN 100mW 100nA 150mA 250mV 50V 5V 70 80MHz NPN SOT-323(SC-70) Bipolar (BJT) ROHSToshibaBipolar (BJT)DTC143ZMFHAT2L
SOT-723Digital TransistorsROHM Semiconductor2SA1586-GR,LF
SC-70Bipolar (BJT)ToshibaMM3Z11VT1GX
SOD-323Zener DiodesNexperia
README
PedalMeetingHeadphoneAmp/README.mdPedal Meeting Headphone Amp

エフェクター展示会の試奏ブースでのコミュニケーションを円滑にするために設計されたヘッドフォンアンプです。ギター/ベースの音と会話用のマイク音声をミックスし、ヘッドフォンで聴くことができます。試奏者と出展者が音を共有できると共に、ヘッドフォンを外さずに会話することが可能となります。
※ 電源は、DC9V(センターマイナス)出力のACアダプターで、0.3A以上の電流出力が可能なものを使用してください。
■ 入力
それぞれ独立したゲイン調整を備えています。ゲインを上げ過ぎるとハウリングが起こることがありますのでご注意ください。
-
INST
楽器側の音声出力を接続します。アンプ・キャビネットシミュレータからの接続を想定しています。ゲインは基本的に中央で固定し、微調整として使用してください。
-
MIC1/MIC2
外部マイクを接続します。48Vファンタム電源が必要なマイクには対応していません。
-
MIC3
本体トップ面にあるマイクです。外部マイクがない場合でも、会話を拾うことが可能です。
■ 出力
楽器の音とマイクの音をそれぞれ出力ボリュームで調整できます。
-
PHONES A/B
試奏者用、出展者用のヘッドフォンを接続します。
-
LINE A/B
外部録音機器を接続できます。
■ スイッチ
-
MIC ON/OFF
すべてのマイク入力を一括でミュートします。マイクが楽器の生音を拾うため、会話時以外はマイクをOFF(LED消灯)にすることをお勧めします。
-
MIC 5V
プラグインパワー方式のコンデンサーマイク(BEHRINGER BC LAV 等)を使用する際にONにします。ダイナミックマイク接続時はOFFにします。48Vファンタム電源が必要なマイクには対応していません。
■ 資料
| ■ 主な仕様 | |
|---|---|
| 入力インピーダンス | 47kΩ(INST) 10kΩ(MIC) |
| 出力インピーダンス | 1 kΩ(LINE) 10Ω(PHONES) |
| 最大出力レベル | 2.5 Vrms(LINE) 50 mW + 50 mW, 32Ω(PHONES) |
| コントロール | MIC ON/OFFスイッチ MIC 5Vスイッチ GAINつまみ × 4 VOLつまみ × 4 |
| インジケーター | 赤色LED(電源ON) 青色LED(マイクON) |
| 接続端子 | INST MIC1/2 PHONES A/B LINE A/B 電源入力端子 |
| 消費電流 | 40 mA(無信号時) 300 mA(最大出力時) |
| 外形寸法 | 幅 100 mm × 奥行 130 mm × 高さ 57 mm |
| 質量 | 550 g |
Parts
144| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 1SS387 | myFoot:D_SOD-523_HandSoldering | D3, D4, D5, D6, D7, D9, D10, D11, D12 |
| 8 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R3, R4, R5, R7, R36, R42, R59 |
| 7 | 100k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11, R18, R38, R39, R45, R65, R71 |
| 6 | 1M | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8, R20, R22, R43, R48, R55 |
| 6 | 2.2k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R13, R17, R23, R25, R27 |
| 5 | a | myFoot:my_Hole_1.0mm | *, *, *, *, * |
| 4 | 100n | Capacitor_SMD:C_1206_3216Metric | C2, C10, C14, C41 |
| 4 | 22k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R10, R16, R30 |
| 4 | 2SK880GR | Package_TO_SOT_SMD:SOT-323_SC-70_Handsoldering | Q7, Q8, Q10, Q11 |
| 4 | TC7W66FK | myFoot:SSOP8-P-0.50A | IC2, IC3, IC4, IC5 |
| 3 | 0.1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C25, C30, C31 |
| 3 | 1u | Capacitor_SMD:CP_Elec_4x5.3 | C7, C29, C42 |
| 3 | 2SC4116GR | Package_TO_SOT_SMD:SOT-323_SC-70_Handsoldering | Q1, Q16, Q24 |
| 3 | 2SK879Y | Package_TO_SOT_SMD:SOT-323_SC-70_Handsoldering | Q6, Q17, Q19 |
| 3 | 470k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R29, R37, R58 |
| 3 | 47n | Capacitor_SMD:C_1206_3216Metric | C6, C15, C23 |
| 3 | 47p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C11, C12, C18 |
| 3 | 56n | Capacitor_SMD:C_1206_3216Metric | C26, C27, C45 |
| 3 | DTC143ZMFHA | myFoot:SOT-723_HandSoldering | Q2, Q3, Q4 |
| 2 | (10k) | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R31, R32 |
| 2 | 0.047u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C33, C38 |
| 2 | 10u | Capacitor_SMD:C_1206_3216Metric | C5, C9 |
| 2 | 10u | Capacitor_SMD:CP_Elec_4x5.3 | C28, C32 |
| 2 | 18n | Capacitor_SMD:C_0805_2012Metric | C21, C22 |
| 2 | 1k | Resistor_SMD:R_0805_2012Metric | R9, R46 |
| 2 | 2.2n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C16, C24 |
| 2 | 2SA1586GR | Package_TO_SOT_SMD:SOT-323_SC-70_Handsoldering | Q9, Q12 |
| 2 | 4.7k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R14, R24 |
| 2 | 47u | Capacitor_SMD:CP_Elec_5x5.3 | C1, C4 |
| 1 | 1.2k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R35 |
| 1 | 1.5k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R15 |
| 1 | 100kA | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | VR2 |
| 1 | 100p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C17 |
| 1 | 100u | Capacitor_SMD:CP_Elec_6.3x5.2 | C3 |
| 1 | 10kB | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | VR3 |
| 1 | 15k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R21 |
| 1 | 1u | Capacitor_SMD:C_1206_3216Metric | C8 |
| 1 | 220k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R12 |
| 1 | 220p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C13 |
| 1 | 22n | Capacitor_SMD:C_0805_2012Metric | C44 |
| 1 | 250kA | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | VR1 |
| 1 | 3.3k | Resistor_SMD:R_0805_2012Metric | R47 |
| 1 | 330k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R19 |
| 1 | 33k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R26 |
| 1 | 4.7n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C43 |
| 1 | 5.6k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R28 |
| 1 | 5.6n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C20 |
| 1 | 6.8k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R33 |
| 1 | 6.8n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C19 |
| 1 | 68n | Capacitor_SMD:C_1206_3216Metric | C46 |
| 1 | 820R | Resistor_SMD:R_0805_2012Metric | R34 |
| 1 | 9V Battery | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | BT1 |
| 1 | DC JACK | myFoot:my_DC_Jack | JK1 |
| 1 | DC JACK2 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JK4 |
| 1 | GND | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J4 |
| 1 | INPUT | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JK2 |
| 1 | LED_RB | LED_THT:LED_D3.0mm-3 | D8 |
| 1 | MM3Z11VT1G | Diode_SMD:D_SOD-323_HandSoldering | D2 |
| 1 | MODE | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | SW2 |
| 1 | NCP718BSN330 | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U6 |
| 1 | ON/OFF | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | SW1 |
| 1 | OUTPUT | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JK3 |
| 1 | RB160L-40 | Diode_SMD:D_SMA | D1 |
| 1 | START CUSTOM MODE | myFoot:my_SolderJumper-THpad-DIPsw | JP2 |
| 1 | START EFFECT OFF | myFoot:my_SolderJumper-THpad-DIPsw | JP1 |
| 1 | STM32L010F4P6 | myFoot:TSSOP-20_4.4x6.5mm_P0.65mm_HS | IC7 |
| 1 | SWC | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J3 |
| 1 | SWD | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J2 |
| 1 | TL074 | myFoot:my_TSSOP-14 | IC1 |
More from kanengomibako/EffectsPedals
12- 2 layers55.4 × 66 mm

- 2 layers112 × 80 mm

- 2 layers100 × 80 mm

- 2 layers54 × 83 mm

- 4 layers49.5 × 49.5 mm

- 2 layers99.1 × 80 mm

- 2 layers61 × 100 mm

- 2 layers100 × 100 mm

- 2 layers100 × 100 mm

- 2 layers73 × 100 mm

- 2 layers49.5 × 54.6 mm

- 2 layers54.6 × 48.3 mm

Similar boards
- 2 layers176 × 105 mm

Reference Keyboard
famichu/MagLevSwitch_ReferenceKeyboard
The reference keyboard for the MagLev Switch MX
91 parts2MIT - 2 layers37.2 × 31.2 mm

DeathClock
EmileBV/DeathClock
This project's goal to make a pocket "watch" that will last and run as long as possible and count down to a set date/time.
32 parts - 6 layers100 × 100 mm

- 6 layers45 × 75 mm

- 2 layers24.1 × 56.9 mm

- 2 layers30 × 59 mm

- 2 layers100 × 100 mm

- 2 layers335.9 × 145.9 mm

Split70kb
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
144 parts915
Questions
How big is the Bd2wl PCB?
It measures 90 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Bd2wl use?
144 parts, built around the STM32L010F4P6, TC7W66FK,LF, NCP718BSN330 and 1SS387. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Bd2wl KiCad files?
From the kanengomibako/EffectsPedals repository on GitHub, at the commit this page was made from: the board is BD2wazaLite/KiCad6/bd2wl.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Bd2wl design in my own project?
Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
