
UDEC.CX
dermatoid-collab/EVC_FW
Progetto hardware e firmware del sistema di controllo di un ascensore domestico a trazione (TTF) di LiftingItalia s.r.l. Quattro schede basate su STM32F446, collegate in CAN; il motore è comandato da un VFD.

Autko is an open-source printed circuit board by KamilRosinski, from the KamilRosinski/autko repository on GitHub. It is a 4-layer board of 140 × 155 mm with 131 parts on 108 nets, routed with 616 tracks and 397 vias.
It is built around the ATXMEGA16A4U-AU, CNY70 and SL1A, with the SL52-3G among its other parts. Its parts include 45 resistors, 24 capacitors, 12 diodes, 10 switches and 5 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 20 | TestPoint | TestPoint:TestPoint_Pad_D1.5mm | TP1, TP2, TP10, TP11, TP12, TP13, TP14, TP15, TP16, TP17, TP18, TP19, TP20, TP21, TP22, TP23 +4 |
| 12 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C5, C11, C12, C13, C14, C16, C17, C19, C21, C22, C23 |
| 7 | 20kR | Resistor_SMD:R_0603_1608Metric | R23, R25, R27, R29, R31, R33, R35 |
| 7 | 640R | Resistor_SMD:R_0603_1608Metric | R22, R24, R26, R28, R30, R32, R34 |
| 7 | 680R | Resistor_SMD:R_0603_1608Metric | R15, R16, R17, R18, R19, R20, R21 |
| 7 | CNY70 | Autko:Vishay_CNY70 | S1, S2, S3, S4, S5, S6, S7 |
| 7 | ORANGE | LED_SMD:LED_0603_1608Metric | D5, D6, D7, D8, D9, D10, D11 |
| 6 | 10kR | Resistor_SMD:R_0603_1608Metric | R8, R9, R12, R13, R14, R37 |
| 6 | 1kR | Resistor_SMD:R_0603_1608Metric | R10, R11, R42, R43, R44, R45 |
| 5 | 100R | Resistor_SMD:R_0603_1608Metric | R36, R38, R39, R40, R41 |
| 4 | 10uF | Capacitor_SMD:C_1206_3216Metric | C9, C15, C20, C24 |
| 3 | TestPoint | TestPoint:TestPoint_Keystone_5019_Minature | TP3, TP4, TP5 |
| 2 | 30pF | Capacitor_SMD:C_0603_1608Metric | C10, C18 |
| 2 | 33uF | Capacitor_Tantalum_SMD:CP_EIA-7343-20_Kemet-V | C3, C4 |
| 2 | GREEN | LED_SMD:LED_0603_1608Metric | D3, D4 |
| 2 | Jumper_x4_Bridged | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | JP1, JP2 |
| 1 | 10.2kR | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 100pF | Capacitor_SMD:C_0603_1608Metric | C7 |
| 1 | 18kR | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 1MR | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 1uF | Capacitor_SMD:C_1206_3216Metric | C8 |
| 1 | 2.2nF | Capacitor_SMD:C_0603_1608Metric | C6 |
| 1 | 20mR | Resistor_SMD:R_1206_3216Metric | R4 |
| 1 | 220R | Capacitor_SMD:C_0603_1608Metric | FB1 |
| 1 | 2A | Fuse:Fuse_1812_4532Metric | F1 |
| 1 | 3.3uH | Inductor_SMD:L_12x12mm_H6mm | L1 |
| 1 | 47uF | Capacitor_Tantalum_SMD:CP_EIA-7343-20_Kemet-V | C2 |
| 1 | 4xAA | Autko:Keystone_2481RB | BT1 |
| 1 | 5.1kR | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 53.6kR | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 820R | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 8MHz | Crystal:Crystal_HC49-4H_Vertical | X1 |
| 1 | ATxmega16A4U-A | Package_QFP:TQFP-44_10x10mm_P0.8mm | U3 |
| 1 | BLUE | LED_SMD:LED_0603_1608Metric | D12 |
| 1 | LEFT | Autko:Pololu_DC_micro | M1 |
| 1 | LTC3872 | Package_TO_SOT_SMD:SOT-23-8 | U1 |
| 1 | PDI | Connector_IDC:IDC-Header_2x03_P2.54mm_Vertical | J1 |
| 1 | POWER | Autko:Knitter-Switch_MSS_3112_D | SW1 |
| 1 | RIGHT | Autko:Pololu_DC_micro | M2 |
| 1 | RN4678 | Autko:RN4678 | U5 |
| 1 | SL1A | Diode_SMD:D_SOD-123F | D2 |
| 1 | SL52-3G | Diode_SMD:D_SMB | D1 |
| 1 | START | Autko:12mm_tact_switch | SW2 |
| 1 | STOP | Autko:12mm_tact_switch | SW3 |
| 1 | TB6612FNG | Package_SO:SSOP-24_5.3x8.2mm_P0.65mm | U4 |
| 1 | TLV761 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | ~ | Package_SO:SO-8_3.9x4.9mm_P1.27mm | Q1 |
The 130 most common of 131 parts.

dermatoid-collab/EVC_FW
Progetto hardware e firmware del sistema di controllo di un ascensore domestico a trazione (TTF) di LiftingItalia s.r.l. Quattro schede basate su STM32F446, collegate in CAN; il motore è comandato da un VFD.

GLGPrograms/tinyDiskII
Homemade floppy disk emulator for Apple II series computers


WojciechNowakowski/PCB-designs
Container for PCB designs created by me (in KiCad software mostly)


aguuzzo/GZX
Este proyecto implementa un robot seguidor de líneas basado en un Arduino Nano, 6 sensores CNY70, motores Pololu y un driver de motores.

Pierini-Franco/Repositor_Automatico
The React app provides a way to order multiple products in a single order. At the same time, employees can order a single product

Carlos-Santos-prog/rc-car-esp32
Vehículo RC de combate con seguidor de línea basado en ESP32. Diseño electrónico completo en KiCad 10.
It measures 140 × 155 mm and has 4 copper layers, 1.6 mm thick.
131 parts, built around the ATXMEGA16A4U-AU, CNY70, SL1A and SL52-3G. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the KamilRosinski/autko repository on GitHub, at the commit this page was made from: the board is pcb/Autko.kicad_pcb and its schematic pcb/Autko.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask KamilRosinski before reusing the design.