4 layers40 × 110 mm
MMM main
niektb/sluisbrinkie-eurorack-published
Published Modules of the Sluisbrinkie project
145 parts34
2 layers
Micro meter
kalkyl/micro-meter- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 144
- Nets
- 110
- Pads
- 431
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 5 (file 20171130)
- Created
- 4 Nov 2020
- Updated
- 18 Nov 2020
Overview
Micro meter is an open-source printed circuit board by kalkyl, from the kalkyl/micro-meter repository on GitHub. It is a 2-layer board with 144 parts on 110 nets.
It is built around the STM32F411CEU6, MCP6002-I/SNVAO and XC6206P332MR, with the WS2812C, SM4007 and B5819W among its other parts. Its parts include 48 capacitors, 30 resistors, 30 diodes, 12 connectors and 4 ICs. It belongs with the STM32 boards of this library.
Main components
6
STM32F411CEU6
UFQFPN-48(7x7)-40℃~+85℃ 1.7V~3.6V 100MHz 128KB 12bit 32 Bit 36 512KB ARM Cortex-M4 Built-in FLASH UFQFPN-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)
MCP6002-I/SNVAO
SOIC-8-150mil-40℃~+125℃ 1.8V~6V 100uA 1MHz 1pA 1pA 2 23mA 28nV/√Hz@1kHz 2uV/℃ 4.5mV 600V/ms 76dB Rail-to-Rail Input, Rail-to-Rail Output SOIC-8-150mil Operational Amplifier ROHSMicrochip TechnologyOperational Amplifier
XC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
WS2812C
SMD5050-4P-25℃~+65℃ 0.6mA 1.57mm 3.7V~5.3V 5.4mm 5mm 800Kbit/s B:465nm~475nm、R:620nm~630nm、G:515nm~525nm Built-in power-on reset circuit、Built-in power-on reset circuit、Built-in one-way transmission function G:400mcd~600mcd、R:150mcd~200mcd、B:100mcd~150mcd SMD5050-4P RGB LEDs(Built-in IC) ROHSWorldsemiRGB LEDs(Built-In IC)
SM4007
MELFMELF Diodes - General Purpose ROHSYONGYUTAIDiodes - General Purpose
B5819W
SOD-123-55℃~+125℃ 1.5A 1mA@40V 25A 40V 600mV@1A Standalone SOD-123 Schottky Diodes ROHSMDDSchottky Diodes
Parts
144| Qty | Value | Footprint | References |
|---|---|---|---|
| 25 | 0.1u | Capacitor_SMD:C_0402_1005Metric | C10, C11, C14, C15, C17, C18, C24, C25, C30, C31, C32, C33, C35, C36, C38, C39 +9 |
| 24 | WS2812C | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D2, D10, D11, D12, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23, D24, D25 +8 |
| 8 | 15k | Resistor_SMD:R_0603_1608Metric | R17, R18, R19, R20, R25, R26, R28, R29 |
| 7 | 3k9 | Resistor_SMD:R_0603_1608Metric | R14, R21, R22, R24, R27, R30, R31 |
| 6 | 10u | Capacitor_SMD:C_0603_1608Metric | C8, C9, C12, C13, C16, C19 |
| 5 | 100 | Resistor_SMD:R_0402_1005Metric | R6, R7, R8, R12, R13 |
| 4 | 1n | Capacitor_SMD:C_0603_1608Metric | C20, C21, C22, C23 |
| 4 | 220p | Capacitor_SMD:C_0603_1608Metric | C26, C27, C28, C29 |
| 4 | 22u | Capacitor_SMD:C_0603_1608Metric | C6, C7, C34, C37 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 2k2 | Resistor_SMD:R_0603_1608Metric | R15, R16, R23 |
| 3 | 600@100MHz | Inductor_SMD:L_0805_2012Metric | FB1, FB2, FB3 |
| 3 | SM4007 | Diode_SMD:D_SOD-123F | D4, D5, D30 |
| 3 | TP_GND | TestPoint:TestPoint_Loop_D2.50mm_Drill1.0mm | TP2, TP5, TP9 |
| 2 | 12p | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | GRN | LED_SMD:LED_0805_2012Metric | D6, D13 |
| 1 | 100k | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 10n | Capacitor_SMD:C_0402_1005Metric | C5 |
| 1 | 10u | Inductor_SMD:L_TDK_NLV25_2.5x2.0mm | L1 |
| 1 | 10uF/25V | Capacitor_SMD:C_0805_2012Metric | C3 |
| 1 | 16MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 27k | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 390 | Resistor_SMD:R_0402_1005Metric | R5 |
| 1 | 47 | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 47k | Resistor_SMD:R_0402_1005Metric | R9 |
| 1 | 4u7 | Capacitor_SMD:C_0603_1608Metric | C4 |
| 1 | 5V_OUT | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J10 |
| 1 | 9k1 | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | B5819W | Diode_SMD:D_SOD-123 | D1 |
| 1 | DC_IN | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J1 |
| 1 | I2C / UART | Connector_PinSocket_2.54mm:PinSocket_2x04_P2.54mm_Vertical | J3 |
| 1 | IN1 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J4 |
| 1 | IN2 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J5 |
| 1 | IN3 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J6 |
| 1 | IN4 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J7 |
| 1 | LEDS_DATA | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J11 |
| 1 | LEDS_EXT | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J12 |
| 1 | MCP6002-ISN | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | MP2359 | Package_TO_SOT_SMD:TSOT-23-6 | U1 |
| 1 | SCL_PU | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | SDA_PU | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP2 |
| 1 | SPI | Connector_PinSocket_2.54mm:PinSocket_2x04_P2.54mm_Vertical | J2 |
| 1 | STM32F411CEU6 | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U2 |
| 1 | SWD | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical | J8 |
| 1 | TP_3V3 | TestPoint:TestPoint_Pad_2.0x2.0mm | TP4 |
| 1 | TP_4V3 | TestPoint:TestPoint_Pad_2.0x2.0mm | TP10 |
| 1 | TP_AIN0 | TestPoint:TestPoint_Pad_2.0x2.0mm | TP6 |
| 1 | TP_AIN1 | TestPoint:TestPoint_Pad_2.0x2.0mm | TP7 |
| 1 | TP_DIN | TestPoint:TestPoint_Pad_2.0x2.0mm | TP1 |
| 1 | TP_VAA | TestPoint:TestPoint_Pad_2.0x2.0mm | TP8 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Wuerth_629105150521 | J9 |
| 1 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23 | U3 |
Questions
What parts does the Micro meter use?
144 parts, built around the STM32F411CEU6, MCP6002-I/SNVAO, XC6206P332MR and WS2812C. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Micro meter KiCad files?
From the kalkyl/micro-meter repository on GitHub, at the commit this page was made from: the board is micro-meter.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Micro meter design in my own project?
Its repository states no licence, so its author keeps all rights: ask kalkyl before reusing the design.
Similar boards
- 2 layers55.9 × 121.3 mm
Tregatti stable
tregatti-tech/ESP32ECG
Open design/code version of ECG device based on esp32
147 parts9 - 2 layers103 × 65 mm
- 2 layers48.7 × 24.8 mm
0-10V to-4-20mA Converter
tonycung/0-10V-to-4-20mA-Converter
A simple 0–10 V to 4–20 mA analog signal converter designed with KiCad.
15 parts - 2 layers62.2 × 30.5 mm
- 2 layers385 × 127.3 mm
- 2 layers33.3 × 33.3 mm
ELRSFC
YeetTheAnson/Merlyn411-FlightController
STM32F411 Based AIO Flight Controller. Superseded by [Merlyn435](https://github.com/YeetTheAnson/Merlyn435-Flight-Stack/)
98 parts3 - 4 layers46.6 × 40.6 mm
