

Balancing robot
- Size
- 100 × 50 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 68
- Nets
- 123
- Pads
- 294
- Tracks, vias
- 526, 83
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 25 Dec 2024
- Updated
- 29 May 2025
Overview
Balancing robot is an open-source printed circuit board by JwAhn0830, from the JwAhn0830/stm32_balancingRobot repository on GitHub. It is a 4-layer board of 100 × 50 mm with 68 parts on 123 nets, routed with 526 tracks and 83 vias.
It is built around the STM32F103RBT6, L293DD and L7805CDT-TR, with the LD39050PU33R and 10118194-0001LF among its other parts. Its parts include 20 capacitors, 17 resistors, 9 connectors, 6 ICs and 5 diodes. It belongs with the robots and motor control boards and the ESP32 and STM32 boards of this library.
Main components
5STM32F103RBT6
LQFP-64(10x10)-40℃~+85℃ 128KB 12bit 20KB 2V~3.6V 32 Bit 51 72MHz ARM Cortex-M3 Built-in FLASH LQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)L293DD
SOP-200℃~+70℃ 2 2 4.5V~36V 4.5V~7V 600mA Bipolar Driver Yes SOP-20 Stepper Motor Driver ROHSGcoreMotor Driver ICsL7805CDT-TR
DPAK0℃~+125℃@(Tj) 1 1.5A 2V@(1A) 35V 5V 68dB@(120Hz) 6mA Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive DPAK Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLD39050PU33R
DFN-6(3x3)-40℃~+125℃@(Tj) 1 200mV@(500mA) 20uA 3.3V 30uVrms 5.5V 500mA 65dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive DFN-6(3x3) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators10118194-0001LF
SMD-30℃~+80℃ 1 100V 5P Black Female Micro-B USB 2.0 SMD USB Connectors ROHSAmphenolUSB Connectors
README
schematic/README.mdSchematic
1. main
2. Power
3. CPU_Block
Prototype PCB
Parts
68| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100nF | Capacitor_SMD:C_0603_1608Metric | C6, C7, C8, C9, C10, C14 |
| 4 | 100nF 50V | Capacitor_SMD:C_0603_1608Metric | C2, C18, C20, C21 |
| 4 | 4.7K | Resistor_SMD:R_0603_1608Metric | R4, R6, R7, R18 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 10K | Resistor_SMD:R_0603_1608Metric | R13, R15, R16 |
| 3 | 1uF | Capacitor_SMD:C_0603_1608Metric | C11, C13, C15 |
| 2 | 180 | Resistor_SMD:R_0603_1608Metric | R5, R14 |
| 2 | 22 | Resistor_SMD:R_0603_1608Metric | R10, R11 |
| 2 | 30pF | Capacitor_SMD:C_0603_1608Metric | C16, C17 |
| 1 | 0.33uF | Capacitor_SMD:C_0603_1608Metric | C19 |
| 1 | 1.5K | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 1.5k | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 100 | Resistor_SMD:R_0603_1608Metric | R17 |
| 1 | 100nF/2V | Capacitor_SMD:C_0603_1608Metric | C3 |
| 1 | 100nF/4V | Capacitor_SMD:C_0603_1608Metric | C5 |
| 1 | 10118194-0001LF | 10118194-0001LF:AMPHENOL_10118194-0001LF | J4 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C12 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 2.2nF/50V | Capacitor_SMD:C_0603_1608Metric | C4 |
| 1 | 240 | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 33 | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | Boot0_Conn | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J9 |
| 1 | Boot1_Conn | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J8 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_D14mm_H7mm_P10mm | BZ2 |
| 1 | Conn_01x03_Pin | SS-12D00-G3:SS-12D00 | J1 |
| 1 | Crystal 8Mh/18pF | Crystal:Crystal_HC49-U_Vertical | Y1 |
| 1 | DEBUG[BLUE] | Button_Switch_THT:SW_PUSH_6mm_H9.5mm | SW2 |
| 1 | DEBUG[GREEN] | LED_SMD:LED_0805_2012Metric | D8 |
| 1 | ESP32 | LolinD32:Lolin D32 | U3 |
| 1 | FerriteBead | Inductor_SMD:L_0603_1608Metric | FB1 |
| 1 | GyroPw[RED] | LED_SMD:LED_0805_2012Metric | D2 |
| 1 | L293DD | l293d:SOIC127P1032X265-20N | U8 |
| 1 | L7805CDT-TR | L7805CDT-TR:VREG_L7805CDT-TR | U5 |
| 1 | LD39050PU33R | LD39050PU33R:SON95P300X300X100-7N | U4 |
| 1 | MCUPw[RED] | LED_SMD:LED_0805_2012Metric | D6 |
| 1 | MPU6050 | mpu6050:QFN50P400X400X95-24N | U2 |
| 1 | Motor1 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | M1 |
| 1 | Motor2 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | M2 |
| 1 | MotorPw[RED] | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | PW_Conn | Connector_Molex:Molex_SPOX_5267-02A_1x02_P2.50mm_Vertical | J5 |
| 1 | Power_conn | SS-12D00-G3:SS-12D00 | J7 |
| 1 | PwSelectPin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | RESET | Button_Switch_THT:SW_PUSH_6mm_H9.5mm | SW3 |
| 1 | STM32F103RBT6 | STM32F103RBT6:STM32F103RBT6 | U1 |
| 1 | SWD | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Horizontal | J10 |
| 1 | UART2 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Horizontal | J14 |
| 1 | WiFiPw[BLUE] | LED_SMD:LED_0805_2012Metric | D3 |
Similar boards
- 2 layers99.5 × 36.5 mm

- 2 layers140 × 90 mm

- 2 layers140 × 90 mm

- 4 layers157.5 × 130 mm

Jv thesis
JhonVelasquez/Embedded_system_Synchronize_Plant
Project of a embedded system that synchronizes signals in a plant. There is electronic (PCB) and software design (FreeRTOS for STM32F7).
233 parts2 - 2 layers40 × 50 mm

ProgArm
ProgArm/ProgArm-Hardware
This repository contains only schematic and PCB files. Schematic PDF and Gerber files are attached to every release.
131 parts3GPL-3.0 - 2 layers80 × 74 mm

Hubble metal detector
zartarn15/hubble-metal-detector
STM32-based digital metal detector with custom hardware and embedded DSP firmware.
156 parts2 - 2 layers79.7 × 80 mm

Mainboardv1.2
doobedoobedo/Huebner_Inverter
KiCAD port of https://github.com/jsphuebner/inverter-hardware mainboard V1.2
133 parts1 - 4 layers86 × 59 mm

Questions
How big is the Balancing robot PCB?
It measures 100 × 50 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Balancing robot use?
68 parts, built around the STM32F103RBT6, L293DD, L7805CDT-TR and LD39050PU33R. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Balancing robot KiCad files?
From the JwAhn0830/stm32_balancingRobot repository on GitHub, at the commit this page was made from: the board is schematic/Balancing_robot.kicad_pcb and its schematic schematic/Balancing_robot.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Balancing robot design in my own project?
Its repository states no licence, so its author keeps all rights: ask JwAhn0830 before reusing the design.