
MCU
Jonathan-E-Luna/CustomChargerSchematicPCB
During my groups capstone, I was in charge of the PCB design for all custom hardware components utilized

During my groups capstone, I was in charge of the PCB design for all custom hardware components utilized
Current Switch is an open-source printed circuit board by Jonathan-E-Luna, from the Jonathan-E-Luna/CustomChargerSchematicPCB repository on GitHub. It is a 2-layer board of 73.1 × 48.5 mm with 22 parts on 17 nets, routed with 213 tracks and 207 vias.
It is built around the INA260AIPW, TPS22918TDBVRQ1 and RR1220P-102-D, with the 87520-1010BLF among its other parts. Its parts include 5 resistors, 5 connectors, 4 capacitors, 2 ICs and 2 diodes.
During my groups capstone, I was in charge of the PCB design for all custom hardware components utilized. The boards are subdivided into three main catagories
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 0 ohm | MCU:RESC2012X60N | A0-3.3, A0-GND1, A1-3.3, A1-GND1 |
| 2 | 0.1uF | MCU:CAPC2012X88N | C3, C4 |
| 2 | 4.7k | SwitchCurrent:RES_ERA6AEB472V | R2, R3 |
| 2 | RR1220P-102-D | Library:RESC2012X50N | R4, R5 |
| 2 | WL-SMCW_0805 | Library:WL-SMCW_0805 | D1, D2 |
| 1 | 1725698 | Library:PHOENIX_1725698 | J4 |
| 1 | 220uF | SwitchCurrent:CAPC3216X190N | C1 |
| 1 | 22uF | MCU:CAPC2012X140N | C2 |
| 1 | 59 | SwitchCurrent:RESC2012X50N | R1 |
| 1 | 87520-1010BLF | MCU:AMPHENOL_87520-1010BLF | J3 |
| 1 | Conn_01x01_Pin | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J1 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | INA260AIPW | SwitchCurrent:SOP65P640X120-16N | U1 |
| 1 | TPS22918TDBVRQ1 | SwitchCurrent:SOT95P280X145-6N | U2 |
| 1 | VOUT | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J5 |

Jonathan-E-Luna/CustomChargerSchematicPCB
During my groups capstone, I was in charge of the PCB design for all custom hardware components utilized

Jonathan-E-Luna/CustomChargerSchematicPCB
During my groups capstone, I was in charge of the PCB design for all custom hardware components utilized

Jonathan-E-Luna/CustomChargerSchematicPCB
During my groups capstone, I was in charge of the PCB design for all custom hardware components utilized




purduerov/X17-Pi-Shield
Custom PCB for Purdue IEEE ROV X17. Board powers the and connects sensors to the Pi


stellarcorp/tvsc
Core software repository for the Tennessee Valley Stellar Corporation


ajefferies2/t1conv
100BASE-T1 ↔ 100BASE-TX media converter + dual CAN FD/USB adapter on one board.
It measures 73.1 × 48.5 mm and has 2 copper layers, 1.6 mm thick.
22 parts, built around the INA260AIPW, TPS22918TDBVRQ1, RR1220P-102-D and 87520-1010BLF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Jonathan-E-Luna/CustomChargerSchematicPCB repository on GitHub, at the commit this page was made from: the board is Current Switch.kicad_pcb and its schematic Current Switch.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Jonathan-E-Luna before reusing the design.