Skip to the content
2 layers96.7 × 57.6 mmMCU, the printed circuit board in 3D

During my groups capstone, I was in charge of the PCB design for all custom hardware components utilized

Size
96.7 × 57.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
31
Nets
48
Pads
149
Tracks, vias
427, 497
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
20 Mar 2026
Updated
21 Mar 2026

Overview

MCU is an open-source printed circuit board by Jonathan-E-Luna, from the Jonathan-E-Luna/CustomChargerSchematicPCB repository on GitHub. It is a 2-layer board of 96.7 × 57.6 mm with 31 parts on 48 nets, routed with 427 tracks and 497 vias.

It is built around the CP2102-GM, 87520-1010BLF and SP0503BAHTG. Its parts include 12 connectors, 7 capacitors, 6 resistors, 2 ICs and 2 diodes. It belongs with the ESP32 boards of this library.

Main components

3

README

README.md

CustomChargerSchematicPCB

During my groups capstone, I was in charge of the PCB design for all custom hardware components utilized. The boards are subdivided into three main catagories

  1. Power boards- These boards are Switching Regulators designed to power the microcontronller, Current Switch Board (Will be mentioned later) and a raspberry pi module. Since all power boards use the same switch regulator IC, only one is shown
  2. MCU Board - This board houses an ESP-32 Microcontroller that will controll the Current/Voltage measurement IC (INA260) and the Load Switch TPS22918
  3. Current Switch Board - Houses the INA260 and TPS22918 that will take current from the 5V regulator and deliver power to a load.

Parts

31
QtyValueFootprintReferences
3.1uFMCU:CAPC2012X88NC2, C6, C7
31kohmsMCU:RESC2012X50NR1, R2, R6
31uFMCU:CAPC2012X135NC3, C4, C5
3Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ10, J11, J12
20 ohmsMCU:RESC1005X40R3, R4
2Conn_01x04_PinConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ1, J3
110k ohmsMCU:RESC2012X60NR5
11725656MCU:PHOENIX_1725656J4
122uFMCU:CAPC2012X140NC1
187520-1010BLFMCU:AMPHENOL_87520-1010BLFJ2
1BOOTMCU:SW_1825910-6-4SW2
1CP2102-GMMCU:QFN50P500X500X100-29NU2
1ENMCU:SW_1825910-6-4SW1
1ESP32-WROOM-EPCM_Espressif:ESP32-WROOM-32EU3
1ON1Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalJ5
1ON1Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ9
1ON2Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalJ6
1ON3Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalJ7
1ON4Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalJ8
1SP0503BAHTGMCU:SOT143D1
1WL-SMCW_0805Library:WL-SMCW_0805D2

More from Jonathan-E-Luna/CustomChargerSchematicPCB

3
  • 2 layers73.1 × 48.5 mmCurrent Switch, the printed circuit board in 3D

    Current Switch

    Jonathan-E-Luna/CustomChargerSchematicPCB

    During my groups capstone, I was in charge of the PCB design for all custom hardware components utilized

    22 parts
  • 2 layers41.3 × 79.8 mmRasp Reg, the printed circuit board in 3D

    Rasp Reg

    Jonathan-E-Luna/CustomChargerSchematicPCB

    During my groups capstone, I was in charge of the PCB design for all custom hardware components utilized

    13 parts
  • 2 layers47.2 × 47.2 mmDC JACK, the printed circuit board in 3D

    DC JACK

    Jonathan-E-Luna/CustomChargerSchematicPCB

    During my groups capstone, I was in charge of the PCB design for all custom hardware components utilized

    8 parts

Similar boards

  • 2 layers58.8 × 55.7 mmAiO i2s DAC, the printed circuit board in 3D

    AiO i2s DAC

    martinroger/ipodesp32

    An iPod emulator for 2006-2013 BMW Mini Coopers that need Bluetooth

    102 parts24MIT
  • 2 layers99.8 × 60.2 mmIrrigation IoT, the printed circuit board in 3D

    Irrigation IoT

    VictorRavani/Irrigation_IoT

    This project covers the complete development of Hardware and Firmware for IoT-based supervisory control. It offers all the necessary information and resources so that anyone can set up the system independently.

    79 parts4MIT
  • 2 layers62 × 26 mmIf chg board, the printed circuit board in 3D

    If chg board

    elkel53930/extraice4

    ExtraICE4 is a competition robot called Micromouse.

    47 parts4MIT
  • 2 layers191.3 × 169.2 mmMainboard layout, the printed circuit board in 3D

    Mainboard layout

    ReadHeadRedemption/SeniorDesignSp26Su26

    88 parts
  • 2 layers58.3 × 36.3 mmE LCD2, the printed circuit board in 3D

    E LCD2

    Forairaaaaa/E-LCD2

    板载2.0寸LCD屏幕的 ESP32 核心板

    40 parts3MIT
  • 4 layers91 × 52 mmFilament dryer monitor, the printed circuit board in 3D

    Filament dryer monitor

    alessandrocardelli/filament-dryer-monitor

    ESP32 controller for eSUN eBOX Lite. main is the non-heating SAFE BRING-UP reference; its heater output remains locked OFF.

    110 parts
  • 2 layers45 × 172 mmPh portable refrigerator v2 hw, the printed circuit board in 3D

    Ph portable refrigerator v2 hw

    Blackcastus/ESP32_A7670

    To make it easy for you to get started with GitLab, here's a list of recommended next steps.

    188 parts

Questions

How big is the MCU PCB?

It measures 96.7 × 57.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the MCU use?

31 parts, built around the CP2102-GM, 87520-1010BLF and SP0503BAHTG. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the MCU KiCad files?

From the Jonathan-E-Luna/CustomChargerSchematicPCB repository on GitHub, at the commit this page was made from: the board is MCU.kicad_pcb and its schematic Current Switch.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the MCU design in my own project?

Its repository states no licence, so its author keeps all rights: ask Jonathan-E-Luna before reusing the design.