Skip to the content
4 layers50 × 50 mmSoundBoard, the printed circuit board in 3D

Small wav player pcb project

Size
50 × 50 mm
Copper layers
4
Thickness
1.6 mm
Parts
50
Nets
76
Pads
207
Tracks, vias
349, 98
Pours
6
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
20 Jan 2020
Updated
15 Sep 2020

Overview

SoundBoard is an open-source printed circuit board by joeperri95, from the joeperri95/SoundBoard repository on GitHub. It is a 4-layer board of 50 × 50 mm with 50 parts on 76 nets, routed with 349 tracks and 98 vias.

It is built around the LM4562NA, W25Q128JVSIQ and AMS1117-3.3. Its parts include 21 capacitors, 7 resistors, 5 ICs, 4 diodes and 2 connectors. It belongs with the STM32 boards of this library.

Main components

3

README

README.md

Soundboard

wav audio player

Future considerations

  • MP3 decoder chip

  • transistors to enable/disable peripherals

  • display

  • addon (SAO) header

  • battery power

  • uart output header

  • expose some gpio pins to a header

  • smaller mounting holes

  • connect SWO pin for jlink debug messages

  • headphone jack/driver

  • SPI pins on flash are backwards

  • ground and test points

Rev 1.0 changes

  • Went exlusively with JLCPCB parts and paid for assembly service
  • Removed lipo circuitry, sd card and hall effect sensor
  • Added spi flash to store music
  • Removed FTDI went for a direct USB connection to the STM32
  • Changed to a smaller stm32f405
  • Reworked output stage to include a digital potentiometer
  • Significantly reduced size of board
  • Went to a 4 layer pcb

Parts

50
QtyValueFootprintReferences
11100nCapacitor_SMD:C_0402_1005MetricC8, C9, C10, C11, C12, C13, C14, C16, C17, C19, C21
410uCapacitor_SMD:C_0603_1608MetricC1, C4, C7, C20
4MountingHole_PadMountingHole:MountingHole_4.3mm_M4_PadH1, H2, H3, H4
310kResistor_SMD:R_0603_1608MetricR2, R3, R7
3220Resistor_SMD:R_0603_1608MetricR1, R4, R6
3LEDLED_SMD:LED_0603_1608MetricD2, D3, D4
22.2uCapacitor_SMD:C_0603_1608MetricC5, C6
220pCapacitor_SMD:C_0402_1005MetricC2, C3
2SW_PushButton_Switch_SMD:SW_Push_1P1T_NO_6x6mm_H9.5mmSW1, SW2
110nCapacitor_SMD:C_0402_1005MetricC15
110pCapacitor_SMD:C_0805_2012MetricC18
1150Resistor_SMD:R_0402_1005MetricR5
11AFuse:Fuse_0603_1608MetricF1
125MhzCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
1AMS1117-3.3Package_TO_SOT_SMD:SOT-223-3_TabPin2U1
1Conn_ARM_JTAG_SWD_10Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMDJ2
1D_SchottkyDiode_SMD:D_SOD-123D1
1Ferrite_BeadInductor_SMD:L_0805_2012MetricFB1
1Ferrite_Bead_SmallInductor_SMD:L_0805_2012MetricFB2
1LM4562Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU4
1MCP4021-xxxxSNPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmU3
1STM32F405RGTxPackage_QFP:LQFP-64_10x10mm_P0.5mmU2
1SpeakerSoundboard:speaker_padsLS1
1USB_B_MicroConnector_USB:USB_Micro-B_Amphenol_10103594-0001LF_HorizontalJ1
1W25Q128JVSPackage_SO:SOIC-8_5.23x5.23mm_P1.27mmU5

Similar boards

  • 2 layers123 × 113.5 mmMcguitarpedal, the printed circuit board in 3D

    Mcguitarpedal

    frsaba/mcguitarpedal

    Teensy 4.1 custom built guitar effects pedal. Uses the Teensy Audio Library and LVGL. Custom PCB design and 3D printed enclosure

    123 parts
  • 2 layers67.3 × 74.9 mmEasysdr, the printed circuit board in 3D

    Easysdr

    michalin/easysdr

    Super Simple SDR Receiver

    140 parts115GPL-3.0
  • 2 layers101.6 × 137.4 mmOpenxcvr, the printed circuit board in 3D

    Openxcvr

    dawsonjon/OpenXcvr

    Cost Effective HF transceiver based on max1000 FPGA module

    155 parts38MIT
  • 2 layers81.3 × 33.7 mmSDRReciever, the printed circuit board in 3D

    SDRReciever

    Dizzerin/Software-Defined-Radio

    Quadrature sampling down converter software defined radio

    67 parts24
  • 2 layers97 × 97 mmQO100 RX, the printed circuit board in 3D

    QO100 RX

    barisdinc/N3B_SDR_Transceiver_HW

    V/U/SHF and QO-100 SDR Transceiver Project

    167 parts20GPL-3.0
  • 2 layers300 × 90 mmPreamp, the printed circuit board in 3D

    Preamp

    profdc9/PrettyGoodPreamplifier

    A Pretty Good Preamplifier for Stereo and Subwoofer Use

    222 parts10

Questions

How big is the SoundBoard PCB?

It measures 50 × 50 mm and has 4 copper layers, 1.6 mm thick.

What parts does the SoundBoard use?

50 parts, built around the LM4562NA, W25Q128JVSIQ and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the SoundBoard KiCad files?

From the joeperri95/SoundBoard repository on GitHub, at the commit this page was made from: the board is Schematic/SoundBoard.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the SoundBoard design in my own project?

Its repository states no licence, so its author keeps all rights: ask joeperri95 before reusing the design.