

Roborock CPAP
This repository contains a custom PCB for use with the awesome work at Roborock CPAP. The PCB shields the controller board from any back flow that might occur from the brushless controller.
- Size
- 49.1 × 49.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 31
- Nets
- 6
- Pads
- 26
- Tracks, vias
- 18, 0
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 16 Apr 2023
- Updated
- 28 Oct 2024
Overview
Roborock CPAP is an open-source printed circuit board by jniebuhr, from the jniebuhr/roborock-pcb repository on GitHub. It is a 2-layer board of 49.1 × 49.1 mm with 31 parts on 6 nets, routed with 18 tracks and 0 vias.
It is built around the BZT52C5V1S, SS34 and SS54. Its parts include 3 connectors and 2 resistors.
Main components
3BZT52C5V1S
SOD-323-65℃~+150℃ 1 Independent 1uA 200mW 4.8V~5.4V 480Ω 5.1V 60Ω SOD-323 Zener Diodes ROHSDiodes IncorporatedZener DiodesSS34
SMA(DO-214AC)-55℃~+125℃ 3A 40V 500uA@40V 550mV@3A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky DiodesSS54
SMA(DO-214AC)-55℃~+125℃ 1mA@40V 40V 550mV@5A 5A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
README
README.mdRoborock CPAP PCB
This repository contains a custom PCB for use with the awesome work at Roborock CPAP. The PCB shields the controller board from any back flow that might occur from the brushless controller.
The logic is the same as in the work of stas2z but reshaped to better fit on the back of the blower while also allowing for a cooling fan to be added.

Assembly

BOM
| Quantity | Designation | Description |
|---|---|---|
| 1 | SHOTTKY2 | SS34 Diode |
| 2 | SHOTTKY1 | SS54 Diode |
| 1 | ZENER1, ZENER2 | BZT52C5V1S Diode |
| 1 | R2 | 1206 10kΩ resistor |
| 1 | R1 | 1206 1kΩ resistor |
| 2 | J1, J2 | JST XH 3P 2.54mm |
| 1 | J3 | JST XH 2P 2.54mm |
| 1 | - | 4010 cooling fan 24V |
| 2 | - | M3x6 |
| 4 | - | M3x12 |
| 4 | - | M3 hex nut |
| 4 | - | M3 heat set insert |
Pinout

The pinout can also be found on the back side of your board and may be different from the most recent version (see note below).
Attention:
This motor pinout changed in version 0.2.0 due to a rotation of a connector. The same cables will work though since the connector has only been rotated. Refer to the writing on the back of your board.
In version 0.2.0, the 2 pin fan connector was labeled with switched GND and VCC.
Ordering
In order to support this project, please consider ordering it through my affiliate link.
The gerber and BOM/CPL files can be found under kicad/.
Mounting options
I have also developed some additional mounting options for the Roborock Fan:
- VzBot 235
- more coming soon...
Sponsors
The development of this board was kindly supported by PCBWay who sent me some prototypes of these boards free of charge.
License
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
Parts
31| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | BZT52C5V1S | Diode_SMD:D_SOD-323 | ZD1, ZD2 |
| 2 | BoardMount_Pad | MountingHole:MountingHole_3.2mm_M3_DIN965_Pad_TopOnly | H1, H2 |
| 1 | 10K | Resistor_SMD:R_1206_3216Metric | R2 |
| 1 | 1K | Resistor_SMD:R_1206_3216Metric | R1 |
| 1 | Axial fan 40mm | Roborock-CPAP:Axial fan 40mm | FAN1 |
| 1 | FAN | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J3 |
| 1 | G*** | kibuzzard-658C23F8 | kibuzzard-658C23F8 |
| 1 | G*** | kibuzzard-658C2360 | kibuzzard-658C2360 |
| 1 | G*** | kibuzzard-658C2324 | kibuzzard-658C2324 |
| 1 | G*** | kibuzzard-65D0EC22 | kibuzzard-65D0EC22 |
| 1 | G*** | kibuzzard-658C21F4 | kibuzzard-658C21F4 |
| 1 | G*** | kibuzzard-658C236E | kibuzzard-658C236E |
| 1 | G*** | kibuzzard-658C2303 | kibuzzard-658C2303 |
| 1 | G*** | kibuzzard-659E705B | kibuzzard-659E705B |
| 1 | G*** | kibuzzard-658C23C6 | kibuzzard-658C23C6 |
| 1 | G*** | kibuzzard-659E706B | kibuzzard-659E706B |
| 1 | G*** | kibuzzard-659FE543 | kibuzzard-659FE543 |
| 1 | G*** | kibuzzard-659FE8A4 | kibuzzard-659FE8A4 |
| 1 | G*** | kibuzzard-658C22D5 | kibuzzard-658C22D5 |
| 1 | G*** | kibuzzard-658C2284 | kibuzzard-658C2284 |
| 1 | G*** | kibuzzard-658C47D4 | kibuzzard-658C47D4 |
| 1 | G*** | kibuzzard-658C2410 | kibuzzard-658C2410 |
| 1 | G*** | kibuzzard-658C2312 | kibuzzard-658C2312 |
| 1 | G*** | kibuzzard-658C2196 | kibuzzard-658C2196 |
| 1 | INPUT | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J1 |
| 1 | LOGO | LOGO | G*** |
| 1 | MOTOR | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J2 |
| 1 | SS34 | Diode_SMD:D_SMA | SBD2 |
| 1 | SS54 | Diode_SMD:D_SMA | SBD1 |
Similar boards
- 2 layers86 × 78.3 mm

- 2 layers56 × 96 mm

- 4 layers105 × 30 mm

Better Klipper Expander
Fisheiyy/Better-Klipper-Expander
A RP2040 based 3D Printer Port Expander
95 parts14 - 4 layers144 × 127 mm

Frothfet
hoeken/frothfet
Yarrboard load controller board with current sense, volt sense, fuses, and sender support.
394 parts14GPL-3.0 - 2 layers80.9 × 92.7 mm

Evo Borne
SRA-VJTI/Evo-Borne
This repository focuses on building an open-source morphobot.
126 parts12MIT - 2 layers100 × 60.5 mm

WizServoTester
Abean2k/WizServoTester
A servo controller PCB that can control up to 4 servos using onboard controls and a simple web app.
40 parts5MIT - 2 layers121 × 75.5 mm

Jlctest
cjheath/jlcbasic
JLC Basic parts library for Kicad fetched and converted from EasyEDA
46 parts5 - 4 layers100 × 30 mm

Revo main
ratmuds/revo
a "cheap" 6 DoF robot arm intentionally pushing the limits of low quality hobby servos
58 parts2MIT
Questions
How big is the Roborock CPAP PCB?
It measures 49.1 × 49.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Roborock CPAP use?
31 parts, built around the BZT52C5V1S, SS34 and SS54. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Roborock CPAP KiCad files?
From the jniebuhr/roborock-pcb repository on GitHub, at the commit this page was made from: the board is kicad/Roborock-CPAP.kicad_pcb and its schematic kicad/Roborock-CPAP.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Roborock CPAP design in my own project?
Its repository states no licence, so its author keeps all rights: ask jniebuhr before reusing the design.

