Skip to the content
2 layers21 × 115 mmBuzzer, the printed circuit board in 3D

The buzzers communicate over a local WIFI which can be configured in the firmware.

Size
21 × 115 mm
Copper layers
2
Thickness
1.6 mm
Parts
24
Nets
42
Pads
91
Tracks, vias
204, 23
Pours
1
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
4 Nov 2024
Updated
4 Nov 2024

Overview

Buzzer is an open-source printed circuit board by jmazur, from the jmazur/jeopardy-buzzer repository on GitHub. It is a 2-layer board of 21 × 115 mm with 24 parts on 42 nets, routed with 204 tracks and 23 vias.

It is built around the ESP32-S2-SOLO-N8, PAM8301AAF and BAT60A. Its parts include 5 diodes, 4 capacitors, 3 resistors, 2 ICs and 1 connector. It belongs with the ESP32 boards of this library.

Main components

3

README

README.md

Jeopardy Buzzer

This project is a Jeopardy! inspired buzzer for home use. You can connect up to 10 contestants and 1 host to play trivia game. The first contestant to buzz in locks all the other contestants out.

The buzzers communicate over a local WIFI which can be configured in the firmware.

Hardware

This project uses an ESP 32 S2 SOLO. All schematics and PCB design was completed using KiCAD. The full project can be found in the pcb folder.

There is a known issue with the spacing of the button contacts at the bottom of the pcb, they need a little more space between them. They can still be used as-is (which is why it didn't fixed earlier) but any new boards can use this design change.

This project also uses a non-standard battery. I ran out of time to work on a battery circuit to use a standard AA battery so I opted for a 3.2 Volt 600 mAh LiFePO4 14500 Battery instead. It would be really nice to change this to a single or a pair of AA or AAA batteries in a future version.

Software

All firmware is compiled and sent to the ESP using the Arduino IDE. All files are located in the firmware folder.

There is a flag called IS_HOST which differentiates buzzers between hosts and contestants. There can only ever be 1 host per WIFI network. There can be up to 10 contestants before the network stops allowing new connections.

Parts

24
QtyValueFootprintReferences
422UFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC1, C2, C5, C6
4LEDLED_THT:LED_D5.0mm_ClearD1, D2, D5, D6
210KResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR2, R3
2~Library:Z00C-4G7L1-11000Conn_Button_1, Conn_Button_2
110kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR1
1BAT60ADiode_SMD:D_SOD-323D3
1BATTTestPoint:TestPoint_Pad_D1.0mm3.3V
1BOOTTestPoint:TestPoint_Pad_D1.0mmBOOT
1Conn_02x01Jmazur:JM BATT 14500J1
1ENTestPoint:TestPoint_Pad_D1.0mmEN
1ESP32-S2-SOLOPCM_Espressif:ESP32-S2-SOLOU1
1GNDTestPoint:TestPoint_Pad_D1.0mmGND
1PAM8301AAFresources:SOT95P280X145-6NU2
1SpeakerConnector_Wire:SolderWire-1sqmm_1x02_P7.8mm_D1.4mm_OD3.9mmSPEAKER
1USB_D +TestPoint:TestPoint_Pad_D1.0mm+
1USB_D -TestPoint:TestPoint_Pad_D1.0mm-

More from jmazur/jeopardy-buzzer

1
  • 2 layers25.9 × 135.3 mmBuzzer v1, the printed circuit board in 3D

    Buzzer v1

    jmazur/jeopardy-buzzer

    The buzzers communicate over a local WIFI which can be configured in the firmware.

    29 parts

Similar boards

  • 2 layers124 × 112 mmOpenDropV3, the printed circuit board in 3D

    OpenDropV3

    GaudiLabs/OpenDrop

    Open Source Digital Microfluidics Bio Lab

    318 parts492GPL-3.0
  • 2 layers45 × 40 mmCircuitPythonBadge v1 2, the printed circuit board in 3D

    CircuitPythonBadge v1 2

    neubauek/CircuitPythonBadge

    Open Source Hardware Circuit Python Badge

    91 parts4
  • 2 layers37.8 × 50 mmXilwatch2, the printed circuit board in 3D

    Xilwatch2

    xil-se/xilwatch_hw

    68 parts2
  • 2 layers100 × 117 mmBHV Badge, the printed circuit board in 3D

    BHV Badge

    biomurph/BioVill_Badge

    DEFCON Micro Fluidics Badge Design For Biohacking Village

    270 parts1MIT
  • 2 layers46.7 × 20.3 mmSoundkey, the printed circuit board in 3D

    Soundkey

    daimapi/soundkey

    38 parts1
  • 2 layers134.6 × 70.1 mmPcb lab, the printed circuit board in 3D

    Pcb lab

    wyu31/TECHIN-514-FinalProject

    This GitHub repository is for my TECHIN-514 final project and all my related files will be uploaded and updated to it.

    22 parts1
  • 4 layers150 × 65 mm32blit, the printed circuit board in 3D

    32blit

    Daft-Freak/32blit-hardware-kicad

    Imported and cleaned up 32blit board files

    121 parts
  • 2 layers50 × 50 mmTalkclock, the printed circuit board in 3D

    Talkclock

    dholth/mesh

    53 parts

Questions

How big is the Buzzer PCB?

It measures 21 × 115 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Buzzer use?

24 parts, built around the ESP32-S2-SOLO-N8, PAM8301AAF and BAT60A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Buzzer KiCad files?

From the jmazur/jeopardy-buzzer repository on GitHub, at the commit this page was made from: the board is pcb/buzzer/buzzer.kicad_pcb and its schematic pcb/buzzer/buzzer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Buzzer design in my own project?

Its repository states no licence, so its author keeps all rights: ask jmazur before reusing the design.