

Slarm zero awa20.1
custom-made boards of ARM processors
- Size
- 49.9 × 40.7 mm
- Copper layers
- 4
- Thickness
- 1.2 mm
- Parts
- 133
- Nets
- 388
- Pads
- 883
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 7 (file 20221018)
- Created
- 9 Apr 2023
- Updated
- 1 Aug 2023
Overview
Slarm zero awa20.1 is an open-source printed circuit board by jlywxy, from the jlywxy/slimarm repository on GitHub, published under the GPL-2.0 licence. It is a 4-layer board of 49.9 × 40.7 mm with 133 parts on 388 nets.
It is built around the SY8089AAAC, W25Q128JVSIQ and AXP209. Its parts include 79 capacitors, 24 resistors, 10 ICs, 4 inductors and 3 diodes.
Main components
3SY8089AAAC
SOT-23-5-40℃~+85℃@(TA) 1 1MHz 2.7V~5.5V 2A 55uA Adjustable Buck Buck Built-in Yes SOT-23-5 DC-DC Converters ROHS矽力杰silergyDC-DC ConvertersW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHAXP209
QFN-48-EP(6x6)Overcurrent Protection、Operating status indication、Adjustable current limiting、Power-on timing control QFN-48-EP(6x6) Power Management - Specialized ROHSX-Powers TechBattery Management
README
readme.mdSlimARM Boards
The project is aiming to manufacture custom-made PCB of Embedded MPUs(most having ARM cores; specially-designed for specified usage, slim in dimension).
Author: jlywxy(jlywxy@outlook.com)
License: GPLv2
Board List
Important:
Check board/readme.PCB_DESIGN_STATUS.md before actual PCB manufacture process.
Use verified boards only.
Status of Working Boards:
| Code | Chipset | Core DRAM Clock | PCB Stack EDA | Status |
|---|---|---|---|---|
| Hypericum | Allwinner A20 | 1.2GHz 2x Cortex-A7 400MHz(800Mbps) DDR3 | 4-layer KiCad | ✅final-pcb |
| Carambola | Atmel AT91SAM9G25 | 400MHz ARM926EJ-S 133MHz(266Mbps) DDR2 | 4-layer KiCad | ✅final-pcb |
| Apricot B | Samsung S3C2416X | 400MHz ARM926EJ-S 133MHz(266Mbps) DDR2 | 4-layer LCEDA | pcb-revision |
| Almond B | Samsung S3C2410 | 200MHz ARM920T 133MHz SDR | 4-layer KiCAD | pcb-revision |
| Azalea | Rockchip RK3128 | 1.1GHz 4x Cortex-A7 533MHz(1066Mbps)DDR3 | 4-layer Cadence | pre-sch |
| Clematis | Rockchip RK3188 | 1.1GHz 4x Cortex-A9 533MHz(1066Mbps)DDR3 | 4-layer KiCad | pre-sch |
| Cumquat (*SlimMIPS) | MediaTek MT7620A | 580MHz MIPS24KEc 192MHz(384Mbps) DDR2 | 4-layer KiCAD & Cadence(two versions) | pre-sch |
Project Pipeline: planning -> avail-analyse -> pre-sch -> pcb-fab-test(1-stage pcb) -> software-test -> post-sch -> pcb-revision -> post-pcb-fab-test -> final-pcb -> post-software-test -> done
Lastest Information
(this column started tracking from 2023.5.14)
Carambola(AT91SAM9G25) the second version of hardware released and under test. Note: The first version failed for the wrong tuning of DDR lines. @ 2023.5.14Apricot(S3C2416) hardware final design finished with version/revisionv1r0x205, the software for this board is under development @ 2023.5.17Almond Mini(S3C2410) hardware final design finished with version/revisionv1r1x208@ 2023.5.20Carambolaturning into a stall state for the unclear DDR2 initialization procedures of atmel mpus. @ 2023.5.26Apricotpushed new hardware version v1r1, which fixed UDEV clock input line and added pad teardrops. @ 2023.5.27- added new plan for
Oxalis Mini@ 2023.5.27 - cut down project plan with existing working plan. @ 2023.5.28
Apricot(S3C2416) hardware debug is done, DDR2 initialization is ok. Starting USB 2.0 HS and Linux software debug. @ 2023.6.2- corrected
Apricotddr clock information in project progress chart to 133 MHz. @ 2023.6.2 - dropped
Carambola; startingOxalis Minischematic design. @ 2023.6.4 - revisioning
Carambola; startingHypericum. @ 2023.6.24 Hypericum(a alias ofOxalis Mini)(Allwinner-A20) first board test done, revisioning;Apricot(S3C2416) third board(v1r3) test done, revisioning;Carambolaboard under test. @ 2023.7.2- Fixed SDIO pull-up problem for
Hypericum,Carambola,Apricotboards. @ 2023.7.11 Carambolanewest board tested done; needed to roll back to version that did not pulled up at SDIO, SAM9G25 have internal pull-up for SDIO. @ 2023.7.15Carambola,Hypericumfixed with reset chip, SDIO pull-ups, ExtIO layout. These versions are verified and committed. @2023.7.22
Misc
- the version identifier on silkscreen of boards:
(1)v1r2e3means version 1, revision 2, edition 3.
typically written inversion 1.1.1.
(2)v1r2x202means version 1, revision 2, date May 14th.
typically written inversion 1.1, 5.14.
these types of version identifiers are all used among boards.
Parts
133| Qty | Value | Footprint | References |
|---|---|---|---|
| 62 | 100nF | Capacitor_SMD:C_0402_1005Metric | C1, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C29, C30, C31 +46 |
| 9 | TestPoint | TestPoint:TestPoint_Pad_D1.5mm | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9 |
| 8 | 2.2k | Resistor_SMD:R_0603_1608Metric | R13, R14, R15, R16, R17, R18, R23, R24 |
| 6 | 22uF | Capacitor_SMD:C_0402_1005Metric | C70, C71, C76, C77, C79, C80 |
| 5 | 5.1k | Resistor_SMD:R_0603_1608Metric | R3, R4, R6, R7, R8 |
| 4 | 1uF | Capacitor_SMD:C_0402_1005Metric | C84, C85, C86, C87 |
| 3 | 2.2uH | Inductor_SMD:L_Vishay_IHLP-2525 | L2, L3, L4 |
| 3 | 330R | Resistor_SMD:R_0603_1608Metric | R1, R2, R5 |
| 3 | LED | LED_SMD:LED_0603_1608Metric | D1, D2, D3 |
| 3 | SW_SMD_SPST_4x3x2 | jlywxy:SW_SPST_SWD_4x3x2 | U3, U8, U10 |
| 2 | 200k | Resistor_SMD:R_0603_1608Metric | R20, R21 |
| 2 | 22pF | Capacitor_SMD:C_0603_1608Metric | C4, C5 |
| 2 | 33pF | Capacitor_SMD:C_0402_1005Metric | C72, C73 |
| 2 | 33pF | Capacitor_SMD:C_0603_1608Metric | C2, C3 |
| 2 | SY8089AAAC | jlywxy:SY8089AAAC | U5, U6 |
| 1 | 1.1k | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R19 |
| 1 | 13k | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 16.2k | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 22uH | Inductor_SMD:L_Vishay_IHLP-2525 | L1 |
| 1 | 24MHz | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y2 |
| 1 | 32.768kHz | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1 |
| 1 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C83 |
| 1 | 4.99k | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | 49.9 | Resistor_SMD:R_0603_1608Metric | R22 |
| 1 | AXP209 | jlywxy:AXP209 | U9 |
| 1 | AllWinner-A20 | jlywxy:awa20 | U1 |
| 1 | DF13A-7P-1.25H21 | jlywxy:DF13A-7P-1.25H21 | J2 |
| 1 | K4B8G1646B-MCK0 | jlywxy:K4B8G1646B-MCK0 | U2 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U7 |
| 1 | XC6206PxxxMR | Package_TO_SOT_SMD:SOT-23-3 | U4 |
More from jlywxy/slimarm
12- 4 layers50 × 33.5 mm

- 4 layers64.6 × 39.1 mm

- 4 layers50 × 29.7 mm

- 4 layers49.3 × 40.8 mm

- 4 layers48.2 × 34.6 mm

- 4 layers48.5 × 39 mm

- 4 layers67.5 × 24.3 mm

- 4 layers54.5 × 25.6 mm

- 4 layers42 × 25.6 mm

- 4 layers50 × 23.9 mm

- 2 layers38.3 × 13.4 mm

- 2 layers

Similar boards
- 4 layers80 × 42 mm

Module
vd-rd/sbc_allwinner_a13
Open hardware compute module with Allwinner A13 (ARM-A8 @1GHz), DDR3 (max 512MB) and expansions (USB, GPIO, WiFi, LCD, Audio)
179 parts38 - 4 layers66 × 42 mm

- 4 layers38 × 74 mm

Stratosdrone
equationstratos/STRATOSDRONES
A 4-layer, 36×70 mm Tello-style portrait controller board for the STRATOSDRONE: chip-down ESP32-P4 (flight + camera + hardware H.264) with an ESP32-C6-MINI-1 Wi-Fi co-processor, IMU / barometer / ToF / optical-flow…
115 parts - 6 layers134 × 84.2 mm

- 4 layers100 × 100 mm

- 4 layers120 × 75 mm

- 2 layers299.3 × 93.1 mm

- 2 layers114 × 62 mm

Questions
How big is the Slarm zero awa20.1 PCB?
It measures 49.9 × 40.7 mm and has 4 copper layers, 1.2 mm thick.
What parts does the Slarm zero awa20.1 use?
133 parts, built around the SY8089AAAC, W25Q128JVSIQ and AXP209. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Slarm zero awa20.1 KiCad files?
From the jlywxy/slimarm repository on GitHub, at the commit this page was made from: the board is board/slimarm_hypericum/misc/pcb_deprecated/z_aub/slarm_zero_awa20.1.kicad_pcb and its schematic board/slimarm_almond/misc/pcb_deprecated/almond_v2_16bit_ram/slimarm_classic_2410.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Slarm zero awa20.1 design in my own project?
Its repository publishes it under the GPL-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).