Skip to the content
2 layers11 × 65 mmRnadom, the printed circuit board in 3D

A pcb created to send IR signals to tvs. You click a button and it uses Tv-B-Gone fimware and basically cycles through all the IR signals until a Tv goes like, Oh its time for me to turn off.

Size
11 × 65 mm
Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
25
Pads
57
Tracks, vias
107, 10
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
26 May 2026
Updated
17 Jun 2026

Overview

Rnadom is an open-source printed circuit board by jlegman1, from the jlegman1/IR-Pen repository on GitHub. It is a 2-layer board of 11 × 65 mm with 14 parts on 25 nets, routed with 107 tracks and 10 vias.

It is built around the ATTINY85-20SU. Its parts include 4 resistors, 3 connectors, 2 capacitors, 2 ICs and 1 diode. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

Disclaimer

This project is intended for educational and research purposes only. It should be used responsibly and only in environments where you have permission to transmit infrared signals.

I created a PCB created that sends IR signals to TVs. You click a button and it uses TV-B-Gone firmware to cycle through all IR signals until a TV turns off. A custom 3d printed shell goes around it hiding the pcb. All kicad files and 3d print files linked. I had created this project because I was playing around with my flipper zero and thought how funny it was to when I turned the tv off when my dad was watching. It gave me motiavtion to create something of my own, so which i did. Overall I hope you enjoy playing around with my desgin! PCB fits through my 3d printed shell and should fit there tightly but shouldn't fall out. Its diamater is 13mm and its 133mm in height. The PCB is 11mm x 65mm.

Firmware created by Mitch Altman and adafruit TV-B-Gone

Parts List

  • 10440 Lithium Battery 3.7V — power source that slides into pen body — Amazon
  • USBasp Programmer — for flashing firmware via ISP pads — Amazon
  • Tactile Button — trigger to fire IR codes — DigiKey
  • 10µF Capacitor — handles big voltage dips — DigiKey
  • 100nF Capacitor — smooths out voltage spikes — DigiKey
  • 33Ω Resistor — limits current to IR LED — DigiKey
  • 3.3kΩ Resistor — keeps charging at 300mA — DigiKey
  • 10kΩ Resistors x2 — keeps ATtiny RESET and button pin stable — DigiKey
  • USB-C Connector — charges the battery — DigiKey
  • 2N7002 MOSFET — switch that drives the IR LED — DigiKey
  • Keystone 5223 — battery spring contact — DigiKey
  • TSAL6400 — IR LED — DigiKey
  • MCP73831T — battery charger IC — DigiKey
  • ATtiny85-20SU — main microcontroller — DigiKey
  • Downloadable CSV up top

Screenshot 2026-05-26 at 2 52 33 PM Screenshot 2026-05-26 at 11 50 53 AM Screenshot 2026-05-27 at 10 30 16 PM

Parts

14
QtyValueFootprintReferences
210kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR1, R4
1100nCapacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolderC1
110uCapacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolderC2
12N7002Package_TO_SOT_SMD:SOT-23Q1
13.3kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR3
133Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR2
1ATtiny85-20SPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmU1
1Conn_01x02Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ2
1Conn_01x06TestPoint:TestPoint_Pad_1.0x1.0mmJ1
1LEDLED_THT:LED_D5.0mmD2
1MCP73831-2-OTPackage_TO_SOT_SMD:SOT-23-5U2
1SW_PushButton_Switch_SMD:SW_Push_1P1T_NO_Vertical_Wuerth_434133025816SW1
1USB_C_Receptacle_USB2.0_14PConnector_USB:USB_C_Receptacle_GCT_USB4085J3

Similar boards

  • 2 layers65 × 56.5 mmSuperPower RPi KiCAD, the printed circuit board in 3D

    SuperPower RPi KiCAD

    SensorsIot/SuperPower

    Here you should find the best power supplies for your low-power projects

    122 parts600
  • 2 layers18.8 × 8.1 mmDell charger emulator, the printed circuit board in 3D

    Dell charger emulator

    KivApple/dell-charger-emulator

    Emulator of original Dell charger using ATTINY85

    6 parts154
  • 2 layers14 × 17.3 mmSnopf, the printed circuit board in 3D

    Snopf

    snopf/snopf

    snopf USB password token

    18 parts145GPL-2.0
  • 2 layers43.9 × 29 mmC64Saver2-addon, the printed circuit board in 3D

    C64Saver2-addon

    bwack/C64-Saver-bwack

    C64 Saver v1 and v2 - Overvoltage protection for the C64 and its power brick.

    43 parts124
  • 2 layers61 × 36.8 mmKeebcard, the printed circuit board in 3D

    Keebcard

    rsheldiii/Keebcard

    Home of the KeebCard project - Kicad files, code, and more!

    15 parts112
  • 2 layers200 × 100 mmRegalodilara, the printed circuit board in 3D

    Regalodilara

    valerionew/very-good-uc-doggos

    A special graduation present for a special friend. Six microcontrollers in one devboard

    91 parts50
  • 2 layers134.3 × 140 mmAerospace badge, the printed circuit board in 3D

    Aerospace badge

    AerospaceVillage/avBadge_2020

    Aerospace Village Badge 2020

    20 parts28
  • 2 layers50 × 25 mmLoRa Environmental Sensors, the printed circuit board in 3D

    LoRa Environmental Sensors

    spielhuus/LoRa-Environmental-Sensors

    ATtiny85 based LoRa atmospheric sensor board with BME280

    5 parts28

Questions

How big is the Rnadom PCB?

It measures 11 × 65 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Rnadom use?

14 parts, built around the ATTINY85-20SU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Rnadom KiCad files?

From the jlegman1/IR-Pen repository on GitHub, at the commit this page was made from: the board is PCB/Rnadom.kicad_pcb and its schematic PCB/Rnadom.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Rnadom design in my own project?

Its repository states no licence, so its author keeps all rights: ask jlegman1 before reusing the design.