Skip to the content
2 layers119.4 × 55.9 mmPumpMonitor, the printed circuit board in 3D

Code relating to a small LoRa network for remote monitoring and control

Size
119.4 × 55.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
30
Nets
31
Pads
95
Tracks, vias
188, 76
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
27 Jan 2021
Updated
4 Jan 2025

Overview

PumpMonitor is an open-source printed circuit board by jgOhYeah, from the jgOhYeah/Farm-PJON-LoRa-network repository on GitHub, published under the MIT licence. It is a 2-layer board of 119.4 × 55.9 mm with 30 parts on 31 nets, routed with 188 tracks and 76 vias.

It is built around the 24LC16B/P and BC548. Its parts include 12 resistors, 5 capacitors, 4 connectors, 3 ICs and 3 diodes. It belongs with the radio and wireless boards of this library.

Main components

2

README

README.md

Farm-PJON-LoRa-network

Code relating to a small LoRa network for remote monitoring and control. This is a work in progress.

Table of contents

Base stations

Arduino Nano base station

Currently an Arduino Nano and 40x2 Alphanumeric LCD, thinking of swapping the nano with a raspberry pi to allow better data logging and display over an ip network. This is still a work in progress. Needs the lcd graph library I have written to draw graphs on alpha numeric lcds. It is also a work in progress. This can be found here.

Raspberry Pi base station

Currently a work in progress and have not uploaded the files to Github yet, but uses a python script to interface with an SX1278 LoRa module and translate this into MQTT to pass to a Thingsboard server running on the pi.

This branch of the PyLora library is required to talk to the radio module as it has been adapted for python 3.

Battery voltage monitor and electric fence control

This is code currently in use in a device that is monitoring battery charge in a remote solar powered electric fence. It sends a packet with the battery voltage once every few minutes and listens for an incoming packet for a set time after each tansmission. The incoming packet can tell the device to turn the fence on or off or control other aspects of the radio link such as disabling transmissions until another incoming packet enables them or requesting the current status be resent.

Stripboard plans and schematic

I used KiCad to plan a layout on veroboard so that I knew there was room for everything and I didn't end up cutting the wrong tracks. The yellow circles and lines in layer Eco2.User are where tracks should be cut. The KiCad files can be found here. Battery Voltage Monitor Schematic Planned layout on stripboard

Photos

This is a work in progess and as such it is only temperarily mounted in the shed, although you know what they say about temporary things :). Circuit on stripboard in a plastic box

Battery voltage monitor before the mosfet was added for controlling the fence and an external antenna to improve range.

Inside of a shed with fence energiser, battery and monitor

The shed and setup of the battery monitor.

Pressure Pump Monitor

This is a monitor for the main pressure pump of the farm that allows the on time of the pump to be measured to hopefully detect leaks sooner rather than later.

The monitor currently operates by timing how many half seconds the pump is on in a half hour block. At the end of each block, the monitor saves the time to a circular buffer stored in an EEPROM chip, calculates the average on time for all values in the chip and transmits the time on in the last half hour as well as the average on time as a LoRa radio packet using the PJON protocol for addressing.

To detect when the pump is running, a simple current transformer was made by winding the neutral wire in a mains extension lead around a filtering choke from an old power supply. Some electrical spaghetti insulation was placed over the neutral wire to ensure that there are multiple layers of insulation between the primary coil formed by the neutral wire and the secondary coil formed by the ~100 turns of enamal copper wire originally on the choke. This is amplified and rectified by a pair of transistors on the pump monitor circuit board. The current transformer is not particulary linear and the amplifier was designed to output a digital signal, meaning that precise current measurement is not currently an option :). Having said that, the system does seem to be quite reliable in detecting when the pump is on and off.

Using an XL2416CP 16kb EEPROM chip, approximately 20 days worth, or 1023 values can be stored at a time.

Compiling and software upload

The software to handle the circular buffer and talk to the radio module take up most of the program space. Strings to print using sertxd are stored in table memory. To avoid having to calculate string lengths and memory locations, I have been working on an extension to this python preprocessor, currently in this branch that will automatically add and call the correct subroutines whenever a ;#sertxd directive is encountered. If you don't want to use this, you can use the compiled.bas file that will have and the ;#sertxd directives correctly substituted, or use the standard PICAXE Programming Editor 6 that will ignore them as a comment, leaving code that will work, but with cryptic numbers being all that is printed to the serial console.

Stripboard plans and schematics

As with the Battery monitor above, I planned out a layout using Kicad before printing a template and using this to cut tracks and place jumper wires and components in the required places. The Kicad files can be found here. Pump monitor schematic Pump monitor off board wiring Pump monitor veroboard layout

Photos

Circuit on stripboard

Bird's eye view of the circuit.

Circuit showing placement of LEDs

View of the monitor circuit board showing the placement of the indicator LEDs.

Testing, showing the pump and current transformer

Testing and software development showing the pump and current transformer (inside the green and black poly pipe extension of a mains socket).

The pump monitor in its black plastic box with hand drawn labels

The pump monitor in its box.

Future Changes

  • At the moment, there is no alarm detection, but when I get around to it, I will probably implement it as part of this device to avoid issues caused by the radio link not being completely reliable. It would probably establish a baseline on time where all the pump is doing is running for a few seconds every hour to keep pressure up and raise an alarm if the pump is over this for X consecutive blocks of time (i.e. water is being used for an unexpectedly long time or there is a leak). In this way, it would hopefully be fairly sensitive to moderate and high leaks over a few hours, but not raise too many false alarms from watering the gardens and fruit trees.
  • Another thing to do is to rewrite the timing code to use interrupts to detect when the pump has started and stopped to avoid the current situation where the pump is not counted as running even if it is during long operations such as calculating the average times.
  • I recently found out that the 18m2+ chips have support for multiple slots, so it might be useful to put an eeprom debugging program in slot1 that can be called under a specific set of conditions to save having to reflash the chip and alternate between software whenever debugging needs to be done.

Parts

30
QtyValueFootprintReferences
310kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR4, R7, R9
2100uCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC1, C3
2150Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR6, R12
22.2kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR5, R8
2BC548Package_TO_SOT_THT:TO-92_Inline_WideQ1, Q2
1100nCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mmC5
110uCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC2
1180Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR11
1220kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR3
122kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR10
124LC16Package_DIP:DIP-8_W7.62mm_SocketU2
1270Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1
133uCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC4
1470Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2
1AHT20 Temperature SensorConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ4
1AlarmLED_THT:LED_D5.0mm_ClearD2
1LM317_TO-220Package_TO_SOT_THT:TO-220-3_VerticalU1
1PICAXE-18M2Package_DIP:DIP-18_W7.62mm_SocketU3
1PowerLED_THT:LED_D5.0mm_ClearD1
1Power & Current SenseTerminalBlock:TerminalBlock_bornier-3_P5.08mmJ1
1ProgrammingConnector_Molex:Molex_KK-254_AE-6410-03A_1x03_P2.54mm_VerticalJ2
1Pump OnLED_THT:LED_D5.0mm_ClearD3
1Ra01_Breakout_ModulePackage_DIP:DIP-8_W7.62mm_SocketJ3
1SW_PushConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalSW1

More from jgOhYeah/Farm-PJON-LoRa-network

4
  • 2 layers83.8 × 33.7 mmElectricFenceMonitor, the printed circuit board in 3D

    ElectricFenceMonitor

    jgOhYeah/Farm-PJON-LoRa-network

    Code relating to a small LoRa network for remote monitoring and control

    30 parts1MIT
  • 2 layers113 × 44.5 mmGateMonitorLayout, the printed circuit board in 3D

    GateMonitorLayout

    jgOhYeah/Farm-PJON-LoRa-network

    Code relating to a small LoRa network for remote monitoring and control

    27 parts1MIT
  • 2 layers100 × 50 mmBatteryMonitorVeroboardLayout, the printed circuit board in 3D

    BatteryMonitorVeroboardLayout

    jgOhYeah/Farm-PJON-LoRa-network

    Code relating to a small LoRa network for remote monitoring and control

    23 parts1MIT
  • 2 layers61 × 33 mmWaterbabyLayout, the printed circuit board in 3D

    WaterbabyLayout

    jgOhYeah/Farm-PJON-LoRa-network

    Code relating to a small LoRa network for remote monitoring and control

    13 parts1MIT

Similar boards

  • 2 layers77.7 × 166.3 mmDelta pico, the printed circuit board in 3D

    Delta pico

    AaronC81/delta-pico

    Powerful scientific calculator based on the Raspberry Pi Pico

    84 parts57MIT
  • 4 layers76 × 82.5 mmNucleo64 CNC, the printed circuit board in 3D

    Nucleo64 CNC

    terjeio/CNC_Breakout_Nucleo64

    CNC breakout for STM324F411 and ST32F446 development boards

    120 parts22
  • 4 layers58.4 × 62.5 mmCNC Boosterpack, the printed circuit board in 3D

    CNC Boosterpack

    terjeio/CNC_Boosterpack

    A BoosterPack that provides 3-axis motor support for some TI LaunchPads

    74 parts13
  • 4 layers47 × 47 mmMotor Gen2, the printed circuit board in 3D

    Motor Gen2

    RoMeLaUCLA/romela-motor-driver

    Motor driver PCB and firmware designed for RoMeLa actuators.

    151 parts6MIT
  • 2 layers100 × 67 mmLed controller, the printed circuit board in 3D

    Led controller

    markus-k/led-controller-hardware

    KiCAD schematics and design files for my LED controller.

    91 parts5
  • 2 layers65 × 56 mmPiADC2, the printed circuit board in 3D

    PiADC2

    capconix/PiADC2

    PiADC open source project successor, the PiADC2 - A simple data acquisition board for use with the model B Raspberry Pis

    72 parts1
  • 2 layers81.3 × 85.7 mmCNCFia, the printed circuit board in 3D

    CNCFia

    coredump/CNCFia

    CNC Daughte Card for MCU based CNC controllers

    57 parts1

Questions

How big is the PumpMonitor PCB?

It measures 119.4 × 55.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the PumpMonitor use?

30 parts, built around the 24LC16B/P and BC548. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the PumpMonitor KiCad files?

From the jgOhYeah/Farm-PJON-LoRa-network repository on GitHub, at the commit this page was made from: the board is PumpMonitor/PumpMonitorVeroboardLayout/PumpMonitor.kicad_pcb and its schematic BatteryVoltageMonitor/BatteryMonitorVeroboardLayout/BatteryMonitorVeroboardLayout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the PumpMonitor design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).