

Power backplane
KiCad 10 is installed locally on this machine.
- Size
- 120 × 80 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 33
- Nets
- 10
- Pads
- 76
- Tracks, vias
- 115, 15
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 10 Jun 2026
- Updated
- 30 Sep 2026
Overview
Power backplane is an open-source printed circuit board by jdg511, from the jdg511/GAS repository on GitHub. It is a 2-layer board of 120 × 80 mm with 33 parts on 10 nets, routed with 115 tracks and 15 vias.
It is built around the R-78E5.0-0.5, URA2415YMD-10WR3 and BLM18PG471SN1, with the SMAJ33A and SS34 among its other parts. Its parts include 13 capacitors, 8 connectors, 1 resistor, 1 diode and 1 fuse.
Main components
5R-78E5.0-0.5
SIP,11.5x7.6mm-300mA、500mA -5V、5V 1 330uF、680uF 6.5V~36V、7V~31V 81%、90% Buck Short Circuit Protection SIP,11.5x7.6mm DC-DC Power Modules ROHSYLPTECDC-DC Power ModulesURA2415YMD-10WR3
DIP,25.4x25.4mmIsolated Power ModulesYLPTECBLM18PG471SN1
06031 1A 200mΩ 470Ω@100MHz ±25% 0603 Ferrite Beads ROHSMurataFerrite BeadsSMAJ33A
SMA-65℃~+150℃ 1uA 33V 40.6V 400W@10/1000us 53.3V 7.5A@10/1000us TVS SMA ESD and Surge Protection (TVS/ESD) ROHSShandong Jingdao MicroelectronicsESD And Surge Protection (TVS/ESD)SS34
SMA(DO-214AC)-55℃~+125℃ 3A 40V 500uA@40V 550mV@3A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
README
hardware/kicad/README.mdKiCad Workspace
KiCad 10 is installed locally on this machine.
This folder is the intended home for the hardware project once schematic capture starts.
Planned Contents
GAS-Hardware.kicad_proGAS-Hardware.kicad_sch- one schematic file scaffold per board
- board layouts for:
- input-output
- tank-driver-recovery
- ext-tank-routing
- crossfade-feedback-wet-summing
- filter-clipper
Current Status
The KiCad project now has a real top-level hierarchical shell, first-pass real symbol capture across every rev-A child sheet, and a first-pass electrically assigned power/backplane page.
What currently exists:
- file naming
- top-level sheet ownership and page ordering
- title blocks
- top-level system notes
- child-sheet interface labels for global rails, I/O boundary nets, inter-board audio nets, and frozen control nets
- first-pass symbol population on every rev-A board sheet
- first-pass DC-entry, rail-generation, and harness-fanout net assignment on
power-backplane.kicad_sch - PCB placement scaffold files for all six rev-A boards, generated from the documented board envelope assumptions
- DRC-clean placement scaffolds with four M3 mounting holes plus all currently assigned schematic footprints per board
- capture sequencing
- validated CLI export workflow
- a manifest-driven audit script for measuring schematic population progress
What does not yet exist:
- real inter-sheet and intra-sheet pin-level wiring on the five audio/control sheets
- clean ERC after the new symbol-only capture phase
- finished footprint assignment inside every schematic page
- routed copper, zones, final component placement, or Gerber/drill fabrication exports for the PCB files
Capture should now key off:
- rev-a-schematic-packets.md [blocked]
- rev-a-electrical-capture-worksheet.md [blocked]
- rev-a-io-schematic-ready-definition.md [blocked]
- rev-a-ext-routing-schematic-ready-definition.md [blocked]
- rev-a-tank-driver-recovery-schematic-ready-definition.md [blocked]
- rev-a-crossfade-feedback-wet-schematic-ready-definition.md [blocked]
- rev-a-filter-clipper-schematic-ready-definition.md [blocked]
- rev-a-control-backplane-schematic-ready-definition.md [blocked]
- rev-a-interconnect-pin-map.md [blocked]
- rev-a-bringup-sequence.md [blocked]
- rev-a-sheet-population-plan.md [blocked]
- rev-a-symbol-manifest.csv [blocked]
- rev-a-net-label-manifest.csv [blocked]
Verification
During this session, the hierarchical top-level shell and all child sheets were accepted by kicad-cli, and the release-export script still produced schematic PDFs successfully after the interface-label pass.
Important current nuance:
- symbol population is intentionally ahead of real wire placement
kicad-cli sch export pdfstill succeeds- top-level ERC is no longer clean at this intermediate stage because the hierarchical labels are not yet attached to real wires or symbols
- the current ERC result is therefore a known intermediate failure, not a claim that the capture is electrically complete
Current exported folder:
- the historical placeholder export artifact still exists as a file named
hardware/kicad/exports
Repeatable release/export helper:
- export-rev-a-release.ps1 [blocked]
- rev-a-release-manifest.csv [blocked]
Repeatable capture-progress audit:
- audit-rev-a-capture.py [blocked]
- rev-a-capture-audit.md [blocked]
Run:
python hardware/kicad/audit-rev-a-capture.pyCurrent baseline from the latest 2026-06-29 audit:
- top-level hierarchy:
6 / 6child sheets present - populated schematic refs:
88 / 88 - explicit manifest net labels:
82 / 82
Current release-export / ERC baseline from the same session:
- capture audit:
88 / 88planned refs present and82 / 82manifest labels present - top-level ERC:
650known intermediate violations after the I/O-board center-short cleanup pass on2026-06-29 - the I/O child sheet dropped from
404to376local violations in the same pass, and its multiple-net-name collisions dropped from8to2 - the remaining I/O multiple-net-name warnings are the intentional
WD_L_LO <-> WET_SUM_LandWD_R_LO <-> WET_SUM_Rwet-return aliases - the remaining ERC debt is still dominated by top-level unconnected sheet pins, placeholder wire endpoints, off-grid legacy symbol endpoints, and still-unwired child-sheet labels on the non-power sheets
- the power/backplane page itself still stands as the most electrically assigned sheet, but it is not yet the final ripple-decoupling or chassis-bond implementation
Current PCB scaffold baseline:
crossfade-feedback-wet.kicad_pcb:100 mm x 70 mm, 8 electrical footprints, 4x M3 mounting holes, DRC cleanext-tank-routing.kicad_pcb:120 mm x 80 mm, 12 electrical footprints, 4x M3 mounting holes, DRC cleanfilter-clipper.kicad_pcb:140 mm x 90 mm, 19 electrical footprints, 4x M3 mounting holes, DRC cleanio-board.kicad_pcb:160 mm x 75 mm, 50 electrical footprints, 4x M3 mounting holes, DRC cleanpower-backplane.kicad_pcb:150 mm x 95 mm, 14 electrical footprints, 4x M3 mounting holes, DRC cleantank-driver-recovery.kicad_pcb:170 mm x 110 mm, 11 electrical footprints, 4x M3 mounting holes, DRC clean- these are placement scaffolds only and are not routed fabrication outputs
Repeatable PCB footprint placement helper:
- place-rev-a-board-footprints.py [blocked]
Current scripted output root:
hardware/kicad/release-exports/rev-a-release
Order Readiness Gate
Before ordering boards, run:
.\hardware\kicad\test-rev-a-order-readiness.ps1The gate writes:
- rev-a-order-readiness.md [blocked]
- GAS-Hardware-erc-current.json [blocked]
It intentionally fails while any of these are true:
- no
*.kicad_pcbboard layout files exist - top-level ERC has violations
- non-virtual schematic symbols have empty footprint fields
- KiCad/SPICE simulation model properties are absent
The current project is therefore not order-ready. It remains in schematic-capture cleanup before PCB layout, DRC, Gerber/drill export, and simulation setup.
Planned Export Set
- fabrication Gerbers
- drill files
- schematic PDFs
BOM.csv- centroid / position files
- assembly drawings
- bring-up and calibration notes
Parts
33| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | M3 | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 10u | Capacitor_SMD:C_1206_3216Metric | C502, C505, C512 |
| 2 | 100n | Capacitor_SMD:C_1206_3216Metric | C503, C506 |
| 2 | 100u | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C501, C504 |
| 2 | 10u | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C510, C511 |
| 2 | BLM18PG471SN1 | Inductor_SMD:L_0603_1608Metric | FB500, FB501 |
| 1 | 0 | Resistor_SMD:R_1206_3216Metric | R500 |
| 1 | 1.1A PTC MF-MSMF110 | Fuse:Fuse_1812_4532Metric | F500 |
| 1 | 100n | Capacitor_SMD:C_0805_2012Metric | C508 |
| 1 | 100u | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C509 |
| 1 | 220u | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C500 |
| 1 | 47u | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C507 |
| 1 | P500 | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | P500 |
| 1 | P501 | Connector_JST:JST_VH_B3P-VH_1x03_P3.96mm_Vertical | P501 |
| 1 | P502 | Connector_JST:JST_VH_B3P-VH_1x03_P3.96mm_Vertical | P502 |
| 1 | P503 | Connector_JST:JST_VH_B3P-VH_1x03_P3.96mm_Vertical | P503 |
| 1 | P504 | Connector_JST:JST_VH_B3P-VH_1x03_P3.96mm_Vertical | P504 |
| 1 | P505 | Connector_JST:JST_VH_B3P-VH_1x03_P3.96mm_Vertical | P505 |
| 1 | P506 | Connector_JST:JST_VH_B4P-VH_1x04_P3.96mm_Vertical | P506 |
| 1 | P601 | Connector_JST:JST_VH_B4P-VH_1x04_P3.96mm_Vertical | P601 |
| 1 | R-78E5.0-0.5 | Converter_DCDC:Converter_DCDC_RECOM_R-78E-0.5_THT | PS501 |
| 1 | SMAJ33A | Diode_SMD:D_SMA | TVS500 |
| 1 | SS34 | Diode_SMD:D_SMA | D500 |
| 1 | URA2415YMD-10WR3 | GAS:URA_YMD-10WR3 | PS500 |
More from jdg511/GAS
5- 2 layers170 × 110 mm

- 2 layers140 × 90 mm

- 2 layers160 × 75 mm

- 2 layers120 × 80 mm

- 2 layers100 × 70 mm

Similar boards
- 2 layers120.4 × 85.7 mm

ESPrinkler Retic PCB
slippery-carrot/ESPrinkler-Retic-Controller
8-Zone reticulation controller based on ESPHome for Home Assistant
142 parts6GPL-3.0 - 4 layers38 × 38 mm

- 2 layers80 × 46 mm

IMU PLACEMENT STUDY
SpaceCadetJ/LoRa-Autonomous-Boat
An embedded-systems project spanning STM32 firmware, LoRa communication, PCB reconstruction and a documented V2 redesign.
130 parts - 4 layers140 × 70 mm

Rcm
Twistiee/rcm
A CAN-controlled relay driver for a car. 21 universal channels, each of which is simultaneously a low-side output and an input — so the same board builds as a relay controller or as a switch panel, decided in firmware…
159 parts - 2 layers120.5 × 75 mm

Mega r3 sidecar controller rev a
javachaos/arduino_simulator
arduinosimulator is a standalone AVR simulation and board-tooling workspace.
34 partsGPL-3.0 - 2 layers100 × 100 mm

COPIE 0
AssaadMH/shadow-4wd-motor-shield-pcb
The 24-signal interface board that replaces SHADOW's perfboard wiring — and the two pin conflicts that only appeared on re-checking the spec.
154 parts2MIT - 4 layers80 × 60 mm

CAN ECU
dhruxraj/stm32-can-ecu
A compact, "ECU-style" CAN node for learning and prototyping automotive-type embedded software. It has an STM32G4 MCU, a CAN transceiver with protection and switchable termination, a 6-axis IMU, a protected 8-18 V…
77 parts2 - 2 layers160 × 100 mm

Interface board
cepr/daly-to-lithium-balance-adapter
Replacement traction battery for a 2018 Energica Ego. The original Lithium Balance s-BMS master (BMCU) stays in the bike.
112 parts
Questions
How big is the Power backplane PCB?
It measures 120 × 80 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Power backplane use?
33 parts, built around the R-78E5.0-0.5, URA2415YMD-10WR3, BLM18PG471SN1 and SMAJ33A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Power backplane KiCad files?
From the jdg511/GAS repository on GitHub, at the commit this page was made from: the board is hardware/kicad/power-backplane.kicad_pcb and its schematic hardware/kicad/archive/abandoned-top-level/GAS-Hardware.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Power backplane design in my own project?
Its repository states no licence, so its author keeps all rights: ask jdg511 before reusing the design.