

OpenPNP
- Size
- 180 × 140 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 393
- Nets
- 385
- Pads
- 1,381
- Tracks, vias
- 2,851, 466
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 5 Jun 2025
- Updated
- 5 Jun 2025
Overview
OpenPNP is an open-source printed circuit board by jaytektas, from the jaytektas/openPNP_mobo repository on GitHub. It is a 4-layer board of 180 × 140 mm with 393 parts on 385 nets, routed with 2,851 tracks and 466 vias.
It is built around the STM32F407VET6, 74HC2G34GW and TMC2209SILENTSTEPSTICK, with the MAX3078EIN, MCP6004-E/P and LM358 among its other parts. Its parts include 123 resistors, 108 capacitors, 80 connectors, 30 ICs and 4 diodes. It belongs with the STM32 boards of this library.
Main components
10STM32F407VET6
LQFP-100(14x14)-40℃~+85℃ 1.8V~3.6V 12bit 12bit 168MHz 192KB 32 Bit 512KB 82 ARM Cortex-M4 Built-in FLASH LQFP-100(14x14) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)74HC2G34GW
TSSOP-6-1.3mm-40℃~+125℃ 1 2 20uA 2V~6V 5.2mA 5.2mA 74HC 9ns@4.5V,50pF Unidirectional TSSOP-6-1.3mm Buffers, Drivers, Receivers, Transceivers ROHSNexperiaBuffers, Drivers, Receivers, TransceiversTMC2209SILENTSTEPSTICK
-Power Management - Modules ROHSTRINAMIC Motion Control GmbHModulesMAX3078EIN
DIP-8-40℃~+85℃ 1 1 16Mbps 256 3.15V~3.45V 400uA Enable shutdown、Thermal shutdown protection、Hot-swap protection Half-Duplex Transceiver ±16kV DIP-8 RS-485 / RS-422 ICs ROHSHGSEMIRS-485 / RS-422 ICsMCP6004-E/P
PDIP-14-40℃~+125℃ 1.8V~6V 100uA 1MHz 1pA 1pA 23mA 28nV/√Hz@1kHz 2uV/℃ 4 4.5mV 600V/ms 76dB ESD protection Rail-to-Rail Input, Rail-to-Rail Output PDIP-14 Operational Amplifier ROHSMicrochip TechnologyOperational AmplifierLM358
SOP-8-18V~18V 0℃~+70℃ 1.2MHz 10nA 2 24mA 3V~36V 500uA 50nA 5mV 80dB Built-in compensation SOP-8 Operational Amplifier ROHSMSKSEMIOperational AmplifierPCA9545AD
SO-20-300mil2.3V~3.6V、4.5V~5.5V I2C SO-20-300mil Interface - Specialized ROHSNXP SemiconductorsInterface - SpecializedELQ3H4(TA)-G
SSOP-16-175mil-1.27mm-55℃~+110℃ 1.2V 100mV@1mA,20mA 20% 200mW 3.75kV 300% 4 50mA 60mA 80V AC,DC Phototransistor SSOP-16-175mil-1.27mm Transistor, Photovoltaic Output Optoisolators ROHSEverlight ElectronicsTransistor, Photovoltaic Output OptoisolatorsAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSBLC6-2P6
SOT-666-6-40℃~+125℃ 150nA 17V 2 3.5pF 5.25V 5A@8/20us 6V ESD IEC 61000-4-2 Unidirectional SOT-666-6 ESD and Surge Protection (TVS/ESD) ROHSSTMicroelectronicsESD And Surge Protection (TVS/ESD)
Parts
393| Qty | Value | Footprint | References |
|---|---|---|---|
| 59 | 100nF | Capacitor_SMD:C_0603_1608Metric | C36, C37, C38, C39, C40, C41, C42, C43, C100, C101, C103, C105, C106, C107, C108, C109 +43 |
| 54 | 10K | Resistor_SMD:R_0603_1608Metric | R10, R11, R100, R101, R102, R103, R113, R114, R115, R116, R117, R118, R119, R120, R121, R122 +38 |
| 42 | 1K | Resistor_SMD:R_0603_1608Metric | R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23, R24, R25, R26, R27 +26 |
| 33 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J1, J2, J10, J11, J21, J27, J33, J39, J45, J51, J54, J55, J56, J57, J58, J59 +17 |
| 24 | 470pF | Capacitor_SMD:C_0603_1608Metric | C10, C12, C13, C14, C15, C17, C18, C19, C20, C22, C23, C24, C25, C27, C28, C29 +8 |
| 24 | FerriteBead_Small | Inductor_SMD:L_0805_2012Metric | FB1, FB2, FB10, FB11, FB12, FB13, FB14, FB15, FB16, FB17, FB18, FB19, FB20, FB21, FB22, FB23 +8 |
| 19 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J18, J19, J20, J24, J25, J26, J30, J31, J32, J36, J37, J38, J42, J43, J44, J48 +3 |
| 8 | 22uF | Capacitor_SMD:C_1206_3216Metric | C75, C77, C87, C89, C90, C93, C94, C95 |
| 8 | 470K | Resistor_SMD:R_0603_1608Metric | R52, R53, R54, R55, R68, R69, R70, R71 |
| 8 | 5.6K | Resistor_SMD:R_0603_1608Metric | R60, R62, R64, R66, R76, R78, R80, R82 |
| 7 | 74HC2G34 | Package_TO_SOT_SMD:SOT-363_SC-70-6 | U8, U17, U24, U25, U26, U27, U28 |
| 6 | 100uF | Capacitor_SMD:CP_Elec_6.3x7.7 | C6, C11, C16, C21, C26, C31 |
| 6 | 100x4 | Resistor_SMD:R_Array_Convex_4x0603 | RN1, RN2, RN3, RN4, RN5, RN6 |
| 6 | Conn_01x06_Pin | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J23, J29, J35, J41, J47, J53 |
| 6 | Fiducial | Fiducial:Fiducial_1mm_Mask2mm | FID1, FID2, FID3, FID4, FID5, FID6 |
| 6 | Screw_Terminal_01x04 | openPNP:CONN-TH_4P-P5.08_WJ2EDGRC-5.08-4P | J22, J28, J34, J40, J46, J52 |
| 6 | TMC2209_SILENTSTEPSTICK | TMC:MODULE_TMC2209_SILENTSTEPSTICK | U2, U3, U4, U5, U6, U7 |
| 5 | ELQ3H4(TA)-G | Package_SO:SOP-16_4.4x10.4mm_P1.27mm | U9, U10, U11, U12, U13 |
| 5 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2, H3, H4, H5 |
| 4 | 4.7uF | Capacitor_SMD:C_0805_2012Metric | C76, C78, C91, C92 |
| 4 | LED | LED_SMD:LED_0805_2012Metric | D2, D3, D4, D5 |
| 4 | Screw_Terminal_01x02 | openPNP:CONN-TH_2P-P3.81_WJ15EDGRC-3.81-2P | J12, J15, J16, J78 |
| 4 | Screw_Terminal_01x08 | openPNP:CONN-TH_8P-P3.81_WJ15EDGRC-3.81-8P | J3, J4, J7, J13 |
| 3 | 100 | Resistor_SMD:R_0603_1608Metric | R108, R109, R110 |
| 3 | 1uF | Capacitor_SMD:C_0603_1608Metric | C68, C102, C104 |
| 2 | 100K | Resistor_SMD:R_0603_1608Metric | R104, R106 |
| 2 | 10pF | Capacitor_SMD:C_0603_1608Metric | C1, C2 |
| 2 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C3, C4 |
| 2 | LMR51430 | Package_TO_SOT_SMD:SOT-23-6 | U22, U29 |
| 2 | MCP6004 | Package_SO:TSSOP-14_4.4x5mm_P0.65mm | U14, U15 |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_XKB_TS-1187A | SW1, SW2 |
| 2 | Screw_Terminal_01x04x3 | openPNP:CONN-TH_WJ15EDGRC-3.81-4P | J14, J79 |
| 2 | Screw_Terminal_01x06 | openPNP:CONN-TH_WJ15EDGRC-3.81-6P | J5, J6 |
| 2 | XGZP6857D | Package_DIP:DIP-6_W10.16mm | U23, U31 |
| 1 | 120 | Resistor_SMD:R_0603_1608Metric | R92 |
| 1 | 12uH | Inductor_SMD:L_12x12mm_H8mm | L3 |
| 1 | 13.7K | Resistor_SMD:R_0603_1608Metric | R107 |
| 1 | 2K | openPNP:RES-ADJ-SMD_G43AT | RV1 |
| 1 | 2K4 | Resistor_SMD:R_0603_1608Metric | R90 |
| 1 | 380mΩ ±25% 600Ω@100MHz 0603 Ferrite Beads ROHS | Inductor_SMD:L_0603_1608Metric | FB25 |
| 1 | 47 | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 5.23K | Resistor_SMD:R_0603_1608Metric | R105 |
| 1 | 6.8uH | Inductor_SMD:L_12x12mm_H8mm | L1 |
| 1 | 680 | Resistor_SMD:R_0603_1608Metric | R111 |
| 1 | 8Mhz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U21 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J80 |
| 1 | Conn_ARM_JTAG_SWD_10 | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J17 |
| 1 | LM358 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U16 |
| 1 | MAX3078E | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U19 |
| 1 | PCA9545 | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U30 |
| 1 | STM32F407VET6 | Package_QFP:LQFP-100_14x14mm_P0.5mm | U1 |
| 1 | Screw_Terminal_01x02x5 | openPNP:CONN-TH_2P-P5.08_WJ2EDGRC-5.08-2P | J75 |
| 1 | USBLC6-2P6 | Package_TO_SOT_SMD:SOT-666 | U20 |
| 1 | USB_B | openPNP:USB-B_TH_BF90 | J74 |
Similar boards
- 4 layers150 × 105 mm

- 4 layers189.6 × 85.9 mm

Super3DMakerSTM
ChladpavPy/Super3DMaker
So first I want to explain, why I started this project. I had an old Profi3DMaker 3D printer at home, which was not used for a long time, mainly because of the hardware, which was just outdated.
147 partsMIT - 2 layers58.4 × 50 mm

- 2 layers35.6 × 19.1 mm

- 2 layers90 × 80 mm

Kanalog jp12-breakout
festlv/kanalog-jp12-breakout
Breakout board for KFlop's Kanalog JP12 (adds 8 inputs, 8 outputs to Kanalog)
103 parts - 2 layers100 × 100 mm

- 4 layers33.5 × 66.8 mm

Net bmp
elagil/net-bmp
An Ethernet-connected SWD/JTAG debug adapter (blackmagic probe)
97 parts3GPL-3.0 - 4 layers96 × 50 mm

Questions
How big is the OpenPNP PCB?
It measures 180 × 140 mm and has 4 copper layers, 1.6 mm thick.
What parts does the OpenPNP use?
393 parts, built around the STM32F407VET6, 74HC2G34GW, TMC2209SILENTSTEPSTICK and MAX3078EIN. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the OpenPNP KiCad files?
From the jaytektas/openPNP_mobo repository on GitHub, at the commit this page was made from: the board is openPNP.kicad_pcb and its schematic analog.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the OpenPNP design in my own project?
Its repository states no licence, so its author keeps all rights: ask jaytektas before reusing the design.