Skip to the content
4 layers95 × 62 mmDevice, the printed circuit board in 3D

Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack

Size
95 × 62 mm
Copper layers
4
Thickness
1.6 mm
Parts
21
Nets
30
Pads
85
Tracks, vias
0, 7
Pours
2
Routed
Not yet
KiCad
KiCad 8 (file 20240108)
Created
12 Jun 2026
Updated
6 Nov 2026

Overview

Device is an open-source printed circuit board by jayis1, from the jayis1/hardware-design-lab repository on GitHub. It is a 4-layer board of 95 × 62 mm with 21 parts on 30 nets.

It is built around the CC2642R1FRGZ, STM32U575ZIT6 and BMP390, with the DS18B20, TPS62740DSS and NE555 among its other parts. Its parts include 14 ICs, 2 capacitors and 2 connectors. It belongs with the STM32 boards of this library.

Main components

10

README

README.md

Hardware Design Lab

Author: jayis1

Full-cycle, open-source hardware device designs — from concept to KiCad schematics to production firmware to companion mobile apps. Every device is fully open: schematics, board layouts, C/Python firmware, and React Native apps. Each device lives in its own subfolder with complete deliverables.

What's Inside Every Device

Every device folder contains the full stack — not just docs, but real buildable artifacts:

CategoryFilesDescription
Engineering Docsphase1_conceptual_architecture.md → phase4_software_stack.md4-phase design process: requirements, BOM & netlists, PCB layout rules, software stack
KiCad Schematicskicad/*.kicad_pro, *.kicad_sch, *.kicad_pcbFull schematic with real component symbols, net labels, power flags, and board outline with placed footprints
C/Python Firmwarefirmware/main.c, registers.h, board.h, drivers/, MakefileProduction-quality MCU firmware — init code, drivers with DMA, USB descriptors, wire protocol
React Native Appapp/App.js, screens/, components/, utils/protocol.js, package.jsonCompanion mobile app for device control, configuration, and status display

Design Methodology

Every device follows the same rigorous 4-phase process:

PhaseDocumentContents
Phase 1phase1_conceptual_architecture.mdPurpose, performance targets, constraints, block diagram, bus topology, power domains
Phase 2phase2_component_selection_schematics.mdBOM with real part numbers, pinouts/MUX tables, decoupling networks, netlists, impedance matching
Phase 3phase3_pcb_blueprints_layout.mdPCB stackup, routing rules, length matching, via strategy, thermal management, DFM notes
Phase 4phase4_software_stack.mdMMIO/register defs, clock & GPIO init (production C), critical device driver, device tree, bootloader

Devices

#DeviceStatusDescription
1eag-7000/ — Edge AI Gateway✅ Docs complete, KiCad/firmware/app pendingi.MX8MP + Hailo-8 NPU, 30 TOPS, fanless industrial, 2×2.5GbE, CAN-FD
2chronos-rtk/ — Dual-Frequency RTK GNSS Receiver✅ CompleteZED-F9P + STM32L4 + LoRa mesh, cm-level positioning, 868/915 MHz ISM
3vortex-sdr/ — Portable SDR Spectrum Analyzer✅ CompleteSTM32H743 + iCE40UP5K FPGA + ADF4351 PLL, 100kHz–6GHz, dual-FFT waterfall
4web-slack-ledger/ — WebSlack LedgerBuild-tested prototype; physical validation pendingTwo-encoder differential travel and reversal ledger for slow hand-fed strip fixtures
5slip-window/ — Slip WindowBuild-tested prototype; physical validation pendingSlip-casting cradle residence, interrupted draining, longest drain segment, and mold-opening notebook
6stencil-orbit/ — Stencil OrbitBuild-tested prototype; physical validation pendingManual screen-printing carousel station index, registration continuity and per-station tool-use notebook
7crossover-track/ — Crossover TrackBuild-tested prototype; physical validation pendingFour-contact cart trial recorder and guided ABBA lane-swap comparison separating cart and lane time contrasts
8takeup-atlas/ — Takeup AtlasBuild-tested prototype; physical validation pendingTwo-shaft reversal trials recording first output response, three-edge confirmation and rejected attempts in hand-operated mechanisms
9chord-window/ — Chord WindowBuild-tested prototype; physical validation pendingFour-switch chord press spread, shared hold and release timing before keyboard filtering, with local policy comparison
10detent-loop/ — Detent LoopBuild-tested prototype; physical calibration pendingHand-operated sliding-catch force–travel loops with explicit zero, turnaround, signed work and local evidence export
11tilt-break/ — Tilt BreakBuild-tested prototype; physical calibration pendingManual incline home-departure resistance brackets and independently qualified downstream puck arrival
12pipette-path/ — Pipette PathBuild-tested prototype; physical training validation pendingTwo-stop manual pipette plunger sequence recorder with operator-declared source immersion; not a volume calibrator
13flow-pause/ — Flow PauseBuild-tested prototype; physical validation pendingDeclared-supply hopper discharge silence, intervention precedence and recovery notebook; not a blockage detector
14sieve-shuttle/ — Sieve ShuttleBuild-tested prototype; physical validation pendingFour-zone manual sieving motion matrix, opposite-axis traversals, same-zone returns and longest directional runs; not separation efficiency
15bellows-phase/ — Bellows PhaseBuild-tested prototype; physical validation pendingDirection-conditioned inlet/outlet flap-position intervals across manual bellows strokes; not airflow or efficiency
16shutter-quartet/ — Shutter QuartetBuild-tested prototype; optical validation pendingFour-point fragmented exposure, missing-point and reopening notebook for slow hand-operated teaching shutters; not camera calibration
17coupon-transit/ — Coupon TransitBuild-tested prototype; physical validation pendingTwo-holder rack-to-rack transfer durations, same-rack returns and interrupted-observation notebook; not specimen identity or treatment verification
18pattern-sled/ — Pattern SledBuild-tested prototype; physical validation pendingThree-track mechanical program-strip repeat comparator with a learned sixteen-word reference, per-position mismatches and terminal alignment-loss diagnostics
19kit-multiset/ — Kit MultisetBuild-tested prototype; physical validation pendingTray-delimited unordered 2:1:1 bin-paddle recipe declarations, conservative abandonment and local evidence export; not inspected part quantities
20shim-bracket/ — Shim BracketBuild-tested prototype; physical validation pendingIndexed feeler-gauge fit/refusal declarations with persistent monotonicity contradictions; not calibrated gap measurement
21catch-witness/ — Catch WitnessBuild-tested prototype; physical validation pendingSettled-latch reopening notebook with expiring handle/tug associations and separate unseated, unexplained and aborted outcomes; not a retention-force gauge
22beat-aperture/ — Beat ApertureBuild-tested prototype; physical validation pendingTwo-pendulum return apertures retaining zero, single and multiple comparison returns within each reference cycle; not continuous phase measurement
23grip-lattice/ — Grip LatticeBuild-tested prototype; physical validation pendingFootswitch-delimited three-zone dummy-handle contact combinations, segment lengths and explicit unknown intervals; not a force or ergonomic assessment instrument

EAG-7000 — Edge AI Gateway

A high-performance, fanless industrial Edge AI Gateway for real-time ML inference at the network edge.

System Specifications

ParameterValue
AI Throughput≥30 TOPS INT8 (2.3 TOPS SoC + 26 TOPS Hailo-8)
CPUNXP i.MX8M Plus — 2× Cortex-A72 @ 2.0 GHz + 1× Cortex-M4F @ 800 MHz
Memory2× Micron MT53D512M32D4DS — 8GB LPDDR4X @ 4267 MT/s
Storage32GB eMMC 5.1 (boot) + 128GB NVMe M.2 2242 (data)
Networking2× 2.5GbE (AQR111C) + 1× 5GbE USB-C
Industrial IO2× CAN-FD, 3× SPI, 4× I2C, 5× UART, 1× MIPI-CSI2
Power12V DC / PoE+ (802.3at), ≤15W typical, 25W peak
Form Factor100mm × 72mm × 25mm, DIN-rail mountable
Operating Temp-40°C to +85°C (industrial)

Key Design Decisions

  1. i.MX8M Plus over Rockchip RK3588 — 15-year industrial availability, verified -40°C to 85°C
  2. LPDDR4X over DDR4 — 1.1V IO for passive cooling at 15W TDP
  3. eMMC boot over SD card — vibration reliability in industrial environments
  4. Hailo-8 M.2 accelerator — 26 TOPS at 2.5W, best TOPS/W in form factor
  5. Dual CAN-FD via SPI (MCP2518FD) — M4F handles real-time fieldbus with <1ms response

Vortex-SDR — Portable SDR Spectrum Analyzer

A portable, handheld spectrum analyzer covering 100 kHz to 6 GHz with dual-channel FFT, real-time waterfall display, capacitive touchscreen, and BLE companion app. Designed for RF engineers, ham radio operators, and EMC compliance testing.

System Specifications

ParameterValue
Frequency Range100 kHz – 6 GHz (dual-conversion superheterodyne)
MCUSTM32H743ZIT6 — Cortex-M7 @ 480 MHz, 1MB Flash, 1MB RAM
FPGALattice iCE40UP5K — FFT/waterfall acceleration
PLL SynthesizerADF4351 — 35 MHz to 4.4 GHz (6 GHz with ADF5002 prescaler)
ADCAD9645 — 14-bit, 61.44 MSPS dual-channel
DisplayILI9341 — 2.8" 320×240 TFT with capacitive touch
BLEnRF52840 — 2 Mbps BLE 5.0 companion link
Power3.7V LiPo (TPS62A02 buck + AMS1117 LDO), USB-C charging
Form Factor120mm × 75mm × 18mm, handheld
Operating Temp-20°C to +55°C (commercial)

Key Design Decisions

  1. STM32H743 over STM32F4 — Cortex-M7 @ 480 MHz for real-time FFT processing, dual-issue FPU
  2. iCE40UP5K FPGA for FFT offload — 5280 LUTs, on-chip RAM for windowing and averaging
  3. Dual-conversion architecture — 1st LO (ADF4351) + 10.7 MHz IF for image rejection
  4. AD9645 dual ADC — simultaneous I/Q sampling, 14-bit resolution for dynamic range
  5. Battery-powered with USB-C — TPS62A02 2A buck for efficiency, MCP73871 charger

License

ComponentLicense
Hardware design (KiCad)CERN-OHL-S v2
C firmware & driversGPL-2.0
Python tools & scriptsMIT
React Native companion appsMIT

Parts

21
QtyValueFootprintReferences
1100nFCapacitor_SMD:C_0402_1005MetricC2
110µFCapacitor_SMD:C_0805_2012MetricC3
1BMP390Sensor_Bosch:BMP390U11
1CC2642R1FPackage_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mmU14
1DS18B20Package_TO_SOT_THT:TO-92_InlineU12
1LC709203FPackage_SON:WSON-8-1EP_2x3mm_P0.5mm_EP0.6x2.3mmU19
1LiFePO4_18650Battery:BatteryHolder_Keystone_1042_18650BT1
1MLX90632Sensor_Melexis:MLX90632U2
1NE555Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU7
1OPA2376Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU9
1PCB_Loop_915MHzRF_Antenna:PCB_Loop_915MHzAE1
1PCB_Meander_2.4GHzRF_Antenna:PCB_Meander_2.4GHzAE2
1RV-3028-C7Package_CSTCR:RV-3028-C7U16
1SHT45Sensor_Sensirium:SHT4xU10
1SPV1050Package_DFN_QFN:QFN-16-1EP_4x4mm_P0.65mm_EP2.5x2.5mmU17
1STM32U575ZIT6Package_QFP:LQFP-64_10x10mm_P0.5mmU1
1SX1262RF_Module:Semtech_SX1262U13
1Solar_1.5WConnector_JST:JST_PH_S2B-PH-K_1x02_P2.00mmJ2
1TPS62740Package_SON:WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mmU18
1USB-C_2.0Connector_USB:USB_C_Receptacle_GCT_USB4105J1
1W25Q80DVPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmU15

More from jayis1/hardware-design-lab

12
  • 6 layers120 × 80 mmDevice, the printed circuit board in 3D

    Device

    jayis1/hardware-design-lab

    Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack

    41 parts
  • 4 layers34 × 28 mmDevice, the printed circuit board in 3D

    Device

    jayis1/hardware-design-lab

    Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack

    30 parts
  • 4 layers42 × 85 mmDevice, the printed circuit board in 3D

    Device

    jayis1/hardware-design-lab

    Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack

    26 parts
  • 2 layers120 × 18 mmDevice, the printed circuit board in 3D

    Device

    jayis1/hardware-design-lab

    Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack

    25 parts
  • 4 layers85 × 52 mmDevice, the printed circuit board in 3D

    Device

    jayis1/hardware-design-lab

    Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack

    24 parts
  • 160 × 120 mmDevice, the printed circuit board in 3D

    Device

    jayis1/hardware-design-lab

    Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack

    24 parts
  • 5 layers62 × 52 mmTideband, the printed circuit board in 3D

    Tideband

    jayis1/hardware-design-lab

    Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack

    24 parts
  • 2 layers95 × 65 mmCryo sentinel, the printed circuit board in 3D

    Cryo sentinel

    jayis1/hardware-design-lab

    Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack

    23 parts
  • 4 layers120 × 80 mmDevice, the printed circuit board in 3D

    Device

    jayis1/hardware-design-lab

    Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack

    23 parts
  • 2 layers80 × 50 mmDevice, the printed circuit board in 3D

    Device

    jayis1/hardware-design-lab

    Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack

    22 parts
  • 4 layers19 × 38 mmGrainguard, the printed circuit board in 3D

    Grainguard

    jayis1/hardware-design-lab

    Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack

    21 parts
  • 4 layers72 × 44 mmDevice, the printed circuit board in 3D

    Device

    jayis1/hardware-design-lab

    Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack

    21 parts

Similar boards

  • 2 layers61.7 × 35.1 mmMS88SF2 eInk display v2, the printed circuit board in 3D

    MS88SF2 eInk display v2

    chacal/pcbs

    Hardware design files for various hobby projects

    61 parts1MIT
  • 4 layers159.6 × 130 mmFE UFPR 4 0, the printed circuit board in 3D

    FE UFPR 4 0

    josearistidesbail/FE_UFPR_4_0

    KiCad 10 project for the board that sits between a TI LAUNCHXL-F28379D (runs the FOC firmware) and an Infineon PrimeSTACK 6PS04512E43W39693 inverter driving an EMRAX 208 motor.

    374 parts
  • 2 layers37.8 × 21.5 mmWiflier EXP, the printed circuit board in 3D

    Wiflier EXP

    cnlohr/wiflier

    ESP8266-based Quadcopter Brain

    61 parts92
  • 2 layers45.1 × 20.1 mmCircuit board design, the printed circuit board in 3D

    Circuit board design

    ImperialSpaceSociety/picotracker-Lora

    This is the code base and hardware design files for the Lora pico tracker to be flown around the world

    55 parts14
  • 2 layers16.5 × 34 mmSurface c, the printed circuit board in 3D

    Surface c

    nununoisy/surface-c

    USB-C PD charger for Surface Pro/Book

    38 parts1
  • 2 layers15 × 30 mmSS@H001, the printed circuit board in 3D

    SS@H001

    SSatH/SSatH

    35 parts
  • 2 layers22 × 28 mmDwatum, the printed circuit board in 3D

    Dwatum

    lab11/polypoint

    Indoor localization based on the DecaWave DW1000.

    14 parts143Apache-2.0

Questions

How big is the Device PCB?

It measures 95 × 62 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Device use?

21 parts, built around the CC2642R1FRGZ, STM32U575ZIT6, BMP390 and DS18B20. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Device KiCad files?

From the jayis1/hardware-design-lab repository on GitHub, at the commit this page was made from: the board is frostsentinel/kicad/device.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Device design in my own project?

Its repository states no licence, so its author keeps all rights: ask jayis1 before reusing the design.