Skip to the content
2 layers100 × 42 mmC100 rev e, the printed circuit board in 3D

Hardware of stm32f10x based nixieclock project

Size
100 × 42 mm
Copper layers
2
Thickness
1.6 mm
Parts
51
Nets
45
Pads
204
Tracks, vias
433, 245
Pours
6
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
3 Jan 2016
Updated
5 Feb 2020

Overview

C100 rev e is an open-source printed circuit board by jan1s, from the jan1s/hw-stm32-nixieclock repository on GitHub. It is a 2-layer board of 100 × 42 mm with 51 parts on 45 nets, routed with 433 tracks and 245 vias.

It is built around the MIC5219-3.3YM5 and USBLC6-2SC6. Its parts include 16 capacitors, 13 resistors, 6 ICs, 5 connectors and 2 diodes. It belongs with the STM32 boards of this library.

Main components

2

README

README.md

hw-nixieclock

The firmware running on the clock: Firmware

A small Gist to configure a STM32 toolchain on Mac: Toolchain

To flash the controller a STM32 Programmer is needed, just get the cheapest one from China.

Initial Configuration

Before the clock will actually start working, it is necessary to set the type:

bash
nixie_settype <type>
nixie_settype <type(0-4)>

Where <type> is a number defining the nixie clock type.

  1. ZM1000
  2. Z570M, IN-8
  3. ZM1325
  4. IN-14, ZM1020

It is also required to set the mode of operation:

bash
nixie_setmode <mode>
nixie_setmode <mode(0=NONE|1=HHMMSS|2=HHMM|3=MMSS|4=YYYY)>

Where <mode> is a number defining the nixie operation mode.

  1. HH:MM:SS
  2. HH:MM
  3. MM:SS
  4. YYYY

PCBs

The clock has seperate control and display pcbs. Those pcbs do not only form a basic case for the electronics, but also allow for flexible use with different tubes.

Control PCBs

Display PCBs

Source PCBs

Parts

51
QtyValueFootprintReferences
5100nFCapacitor_SMD:C_0402_1005MetricC11, C14, C15, C16, C18
510uFCapacitor_SMD:C_0402_1005MetricC2, C4, C5, C12, C13
522RResistor_SMD:R_0402_1005MetricR7, R8, R9, R10, R13
410kResistor_SMD:R_0402_1005MetricR1, R2, R5, R12
31k5Resistor_SMD:R_0402_1005MetricR3, R4, R6
210pCapacitor_SMD:C_0402_1005MetricC8, C9
21uFCapacitor_SMD:C_0402_1005MetricC1, C17
2470pFCapacitor_SMD:C_0402_1005MetricC3, C10
2LED WhiteLED_SMD:LED_0603_1608MetricD1, D2
2LOGOLogos_jan1s:jan1s_16mmG***, G***
2MIC5219-3.3YM5Package_TO_SOT_SMD:SOT-23-5U1, U2
2USBLC6-2SC6Package_TO_SOT_SMD:SOT-23-6U4, U5
132.768kHzCrystal:Crystal_SMD_3215-2Pin_3.2x1.5mmY2
15k1Resistor_SMD:R_0402_1005MetricR11
1AudioJack4_SwitchTR1Connector_Audio:Jack_3.5mm_PJ320D_HorizontalJ4
1Battery_CellBattery:BatteryHolder_Keystone_1060_1x2032BT1
1Conn_01x05Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_VerticalJ1
1Conn_02x05_Odd_EvenConnector_PinSocket_2.54mm:PinSocket_2x05_P2.54mm_Vertical_SMDJ3
1HV5WPower_Modules:HV5W_SMDU6
1LOGOLogos_jan1s:janis.xyz_16mmG***
1STDC14Connector_PinHeader_1.27mm:PinHeader_2x07_P1.27mm_Vertical_SMDJ2
1STM32F072C8TxPackage_QFP:LQFP-48_7x7mm_P0.5mmU3
1SW_PushButton_Switch_SMD:1TS003BSW1
1USB_C_Receptacle_USB2.0Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12J5

The 48 most common of 51 parts.

Similar boards

  • 4 layers43.2 × 43.2 mmROCK Pi S CLAS HAT, the printed circuit board in 3D

    ROCK Pi S CLAS HAT

    takuhoTech/CelestNavi-HAT-for-ROCK-Pi-S

    ROCK Pi S CLAS HAT

    66 parts6MIT
  • 2 layers30 × 68.5 mmDf pill, the printed circuit board in 3D

    Df pill

    epchain/df-pill

    Kicad EDA project of a general purpose STM32F103Cx board

    63 parts2Unlicense
  • 4 layers65 × 45 mmSTM32F446VE Module v1, the printed circuit board in 3D

    STM32F446VE Module v1

    pipipipi2002/stm32f446vetx-dev-module

    Dev Module for STM32F446VETx

    88 parts2GPL-3.0
  • 6 layers100 × 67.8 mm12v-2x6, the printed circuit board in 3D

    12v-2x6

    eggsampler/12v-2x6-Current-Monitor

    For more information, see the schematic or the PCB layout (KiCanvas)

    152 parts1
  • 2 layers54 × 40 mmESP32-S3-Remote, the printed circuit board in 3D

    ESP32-S3-Remote

    dylancollaud/ESP32-S3-Remote

    ESP32-S3-Remote for trigger physical remote

    60 parts
  • 6 layers42.3 × 42.3 mmStepper Motor Controller, the printed circuit board in 3D

    Stepper Motor Controller

    Ricsi1231/Stepper-Motor-Controller

    EmbedCore Stepper Controller is a compact, high-performance stepper motor driver designed to mount directly onto the back of a NEMA 17 motor with the appropriate enclosure.

    91 partsMIT
  • 2 layers20.8 × 52.7 mmNRFpill, the printed circuit board in 3D

    NRFpill

    kien242/Kimiro-nRF52840

    39 partsMIT
  • 2 layers80 × 50 mmThermal Camera, the printed circuit board in 3D

    Thermal Camera

    Circuit-Digest/MLX90640-Thermal-Camera

    An Open Source Thermal Imaging IR camera that you can build yourserlf

    66 parts94

Questions

How big is the C100 rev e PCB?

It measures 100 × 42 mm and has 2 copper layers, 1.6 mm thick.

What parts does the C100 rev e use?

51 parts, built around the MIC5219-3.3YM5 and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the C100 rev e KiCad files?

From the jan1s/hw-stm32-nixieclock repository on GitHub, at the commit this page was made from: the board is layout/control/c100_rev_e/c100_rev_e.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the C100 rev e design in my own project?

Its repository states no licence, so its author keeps all rights: ask jan1s before reusing the design.